1
0

ups.conf 3.6 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104
  1. # Network UPS Tools: example ups.conf
  2. #
  3. # --- SECURITY NOTE ---
  4. #
  5. # If you use snmp-ups and set a community string in here, you
  6. # will have to secure this file to keep other users from obtaining
  7. # that string. It needs to be readable by upsdrvctl and any drivers,
  8. # and by upsd.
  9. #
  10. # ---
  11. #
  12. # This is where you configure all the UPSes that this system will be
  13. # monitoring directly. These are usually attached to serial ports, but
  14. # USB devices and SNMP devices are also supported.
  15. #
  16. # This file is used by upsdrvctl to start and stop your driver(s), and
  17. # is also used by upsd to determine which drivers to monitor. The
  18. # drivers themselves also read this file for configuration directives.
  19. #
  20. # The general form is:
  21. #
  22. # [upsname]
  23. # driver = <drivername>
  24. # port = <portname>
  25. # < any other directives here >
  26. #
  27. # The section header ([upsname]) can be just about anything as long as
  28. # it is a single word inside brackets. upsd uses this to uniquely
  29. # identify a UPS on this system.
  30. #
  31. # If you have a UPS called snoopy, your section header would be "[snoopy]".
  32. # On a system called "doghouse", the line in your upsmon.conf to monitor
  33. # it would look something like this:
  34. #
  35. # MONITOR snoopy@doghouse 1 upsmonuser mypassword master
  36. #
  37. # It might look like this if monitoring in slave mode:
  38. #
  39. # MONITOR snoopy@doghouse 1 upsmonuser mypassword slave
  40. #
  41. # Configuration directives
  42. # ------------------------
  43. #
  44. # These directives are common to all drivers that support ups.conf:
  45. #
  46. # driver: REQUIRED. Specify the program to run to talk to this UPS.
  47. # apcsmart, fentonups, bestups, and sec are some examples.
  48. #
  49. # port: REQUIRED. The serial port where your UPS is connected.
  50. # /dev/ttyS0 is usually the first port on Linux boxes, for example.
  51. #
  52. # sdorder: optional. When you have multiple UPSes on your system, you
  53. # usually need to turn them off in a certain order. upsdrvctl
  54. # shuts down all the 0s, then the 1s, 2s, and so on. To exclude
  55. # a UPS from the shutdown sequence, set this to -1.
  56. #
  57. # The default value for this parameter is 0.
  58. #
  59. # nolock: optional, and not recommended for use in this file.
  60. #
  61. # If you put nolock in here, the driver will not lock the
  62. # serial port every time it starts. This may allow other
  63. # processes to seize the port if you start more than one by
  64. # mistake.
  65. #
  66. # This is only intended to be used on systems where locking
  67. # absolutely must be disabled for the software to work.
  68. #
  69. # maxstartdelay: optional. This can be set as a global variable
  70. # above your first UPS definition and it can also be
  71. # set in a UPS section. This value controls how long
  72. # upsdrvctl will wait for the driver to finish starting.
  73. # This keeps your system from getting stuck due to a
  74. # broken driver or UPS.
  75. #
  76. # The default is 45 seconds.
  77. #
  78. #
  79. # Anything else is passed through to the hardware-specific part of
  80. # the driver.
  81. #
  82. # Examples
  83. # --------
  84. #
  85. # A simple example for a UPS called "powerpal" that uses the fentonups
  86. # driver on /dev/ttyS0 is:
  87. #
  88. # [powerpal]
  89. # driver = fentonups
  90. # port = /dev/ttyS0
  91. # desc = "Web server"
  92. #
  93. # If your UPS driver requires additional settings, you can specify them
  94. # here. For example, if it supports a setting of "1234" for the
  95. # variable "cable", it would look like this:
  96. #
  97. # [myups]
  98. # driver = mydriver
  99. # port = /dev/ttyS1
  100. # cable = 1234
  101. # desc = "Something descriptive"
  102. #
  103. # To find out if your driver supports any extra settings, start it with
  104. # the -h option and/or read the driver's documentation.