openadk/package/kismet/files/kismet.conf

# Kismet config file
# Most of the "static" configs have been moved to here -- the command line
# config was getting way too crowded and cryptic.  We want functionality,
# not continually reading --help!

# Version of Kismet config
version=2005.01.R1

# Name of server (Purely for organiational purposes)
servername=Kismet

# User to setid to (should be your normal user)
suiduser=nobody

# Sources are defined as:
# source=cardtype,interface,name[,initialchannel]
# Card types and required drivers are listed in the README.
# The initial channel is optional, if hopping is not enabled it can be used
# to set the channel the interface listens on.
# YOU MUST CHANGE THIS TO BE THE SOURCE YOU WANT TO USE
source=wrt54g,eth1,wireless
# For v1 hardware uncomment this:
# source=wrt54g,eth2,wireless

# Comma-separated list of sources to enable.  This is only needed if you defined
# multiple sources and only want to enable some of them.  By default, all defined
# sources are enabled.
# For example:
# enablesources=prismsource,ciscosource

# Do we channelhop?
channelhop=true

# How many channels per second do we hop?  (1-10)
channelvelocity=5

# By setting the dwell time for channel hopping we override the channelvelocity
# setting above and dwell on each channel for the given number of seconds.
#channeldwell=10

# Do we split channels between cards on the same spectrum?  This means if 
# multiple 802.11b capture sources are defined, they will be offset to cover
# the most possible spectrum at a given time.  This also controls splitting
# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
channelsplit=true

# Basic channel hopping control:
# These define the channels the cards hop through for various frequency ranges
# supported by Kismet.   More finegrain control is available via the 
# "sourcechannels" configuration option.
# 
# Don't change the IEEE80211<x> identifiers or channel hopping won't work.

# Users outside the US might want to use this list:
# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10

# 802.11g uses the same channels as 802.11b...
defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10

# 802.11a channels are non-overlapping so sequential is fine.  You may want to
# adjust the list depending on the channels your card actually supports.
# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 
defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64

# Combo cards like Atheros use both 'a' and 'b/g' channels.  Of course, you
# can also explicitly override a given source.  You can use the script 
# extras/listchan.pl to extract all the channels your card supports.
defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64

# Fine-tuning channel hopping control:
# The sourcechannels option can be used to set the channel hopping for 
# specific interfaces, and to control what interfaces share a list of 
# channels for split hopping.  This can also be used to easily lock
# one card on a single channel while hopping with other cards.
# Any card without a sourcechannel definition will use the standard hopping
# list.
# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN

# ie, for us channels on the source 'prism2source' (same as normal channel
# hopping behavior):
# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10

# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
# on channel 6 and prism2b to hop normally.  By not setting a sourcechannels 
# line for prism2b, it will use the standard hopping.
# sourcechannels=prism2a:6

# To assign the same custom hop channel to multiple sources, or to split the 
# same custom hop channel over two sources (if splitchannels is true), list
# them all on the same sourcechannels line:
# sourcechannels=prism2a,prism2b,prism2c:1,6,11

# Port to serve GUI data
tcpport=2501
# People allowed to connect, comma seperated IP addresses or network/mask
# blocks.  Netmasks can be expressed as dotted quad (/255.255.255.0) or as
# numbers (/24)
allowedhosts=127.0.0.1
# Maximum number of concurrent GUI's
maxclients=5

# Do we have a GPS?
gps=false
# Host:port that GPSD is running on.  This can be localhost OR remote!
gpshost=localhost:2947
# Do we lock the mode?  This overrides coordinates of lock "0", which will
# generate some bad information until you get a GPS lock, but it will 
# fix problems with GPS units with broken NMEA that report lock 0
gpsmodelock=false

# Packet filtering options:
# filter_tracker - Packets filtered from the tracker are not processed or
#                  recorded in any way.
# filter_dump    - Packets filtered at the dump level are tracked, displayed,
#                  and written to the csv/xml/network/etc files, but not 
#                  recorded in the packet dump
# filter_export  - Controls what packets influence the exported CSV, network,
#                  xml, gps, etc files.
# All filtering options take arguments containing the type of address and
# addresses to be filtered.  Valid address types are 'ANY', 'BSSID',
# 'SOURCE', and 'DEST'.  Filtering can be inverted by the use of '!' before
# the address.  For example,
# filter_tracker=ANY(!00:00:DE:AD:BE:EF)
# has the same effect as the previous mac_filter config file option.
# filter_tracker=...
# filter_dump=...
# filter_export=...

# Alerts to be reported and the throttling rates.
# alert=name,throttle/unit,burst
# The throttle/unit describes the number of alerts of this type that are
# sent per time unit.  Valid time units are second, minute, hour, and day.
# Burst describes the number of alerts sent before throttling takes place.
# For example:
# alert=FOO,10/min,5
# Would allow 5 alerts through before throttling is enabled, and will then
# limit the number of alerts to 10 per minute.
# A throttle rate of 0 disables throttling of the alert.
# See the README for a list of alert types.
alert=NETSTUMBLER,5/min,2
alert=WELLENREITER,5/min,2
alert=LUCENTTEST,5/min,2
alert=DEAUTHFLOOD,5/min,4
alert=BCASTDISCON,5/min,4
alert=CHANCHANGE,5/min,4
alert=AIRJACKSSID,5/min,2
alert=PROBENOJOIN,5/min,2
alert=DISASSOCTRAFFIC,5/min,2
alert=NULLPROBERESP,5/min,5
alert=BSSTIMESTAMP,5/min,5

# Known WEP keys to decrypt, bssid,hexkey.  This is only for networks where
# the keys are already known, and it may impact throughput on slower hardware.
# Multiple wepkey lines may be used for multiple BSSIDs.
# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900

# Is transmission of the keys to the client allowed?  This may be a security
# risk for some.  If you disable this, you will not be able to query keys from
# a client.
allowkeytransmit=true

# How often (in seconds) do we write all our data files (0 to disable)
writeinterval=300

# Where do we get our manufacturer fingerprints from?  Assumed to be in the
# default config directory if an absolute path is not given.
ap_manuf=ap_manuf
client_manuf=client_manuf

# Use metric measurements in the output?
metric=false

# Do we write waypoints for gpsdrive to load?  Note:  This is NOT related to
# recent versions of GPSDrive's native support of Kismet.
waypoints=false
# GPSMap waypoint file.  This WILL be truncated.
waypointdata=%h/.gpsdrive/way_kismet.txt

# How many alerts do we backlog for new clients?  Only change this if you have
# a -very- low memory system and need those extra bytes, or if you have a high
# memory system and a huge number of alert conditions.
alertbacklog=50

# File types to log, comma seperated
# dump    - raw packet dump
# network - plaintext detected networks
# csv     - plaintext detected networks in CSV format
# xml     - XML formatted network and cisco log
# weak    - weak packets (in airsnort format)
# cisco   - cisco equipment CDP broadcasts
# gps     - gps coordinates
logtypes=dump,network,csv,xml,weak,cisco,gps

# Do we track probe responses and merge probe networks into their owners?
# This isn't always desireable, depending on the type of monitoring you're
# trying to do.
trackprobenets=true

# Do we log "noise" packets that we can't decipher?  I tend to not, since 
# they don't have anything interesting at all in them.
noiselog=false

# Do we log corrupt packets?  Corrupt packets have enough header information
# to see what they are, but someting is wrong with them that prevents us from
# completely dissecting them.  Logging these is usually not a bad idea.
corruptlog=true

# Do we log beacon packets or do we filter them out of the dumpfile
beaconlog=true

# Do we log PHY layer packets or do we filter them out of the dumpfile
phylog=true

# Do we mangle packets if we can decrypt them or if they're fuzzy-detected
mangledatalog=true

# Do we do "fuzzy" crypt detection?  (byte-based detection instead of 802.11
# frame headers)
# valid option: Comma seperated list of card types to perform fuzzy detection 
#  on, or 'all'
fuzzycrypt=wtapfile,wlanng,wlanng_legacy,wlanng_avs,hostap,wlanng_wext

# What type of dump do we generate? 
# valid option: "wiretap" 
dumptype=wiretap
# Do we limit the size of dump logs?  Sometimes ethereal can't handle big ones.
# 0 = No limit
# Anything else = Max number of packets to log to a single file before closing
# and opening a new one.
dumplimit=0

# Do we write data packets to a FIFO for an external data-IDS (such as Snort)?
# See the docs before enabling this.
#fifo=/tmp/kismet_dump

# Default log title
logdefault=Kismet

# logtemplate - Filename logging template.
# This is, at first glance, really nasty and ugly, but you'll hardly ever
# have to touch it so don't complain too much.
#
# %n is replaced by the logging instance name
# %d is replaced by the current date as Mon-DD-YYYY
# %D is replaced by the current date as YYYYMMDD
# %t is replaced by the starting log time
# %i is replaced by the increment log in the case of multiple logs
# %l is replaced by the log type (dump, status, crypt, etc)
# %h is replaced by the home directory
# ie, "netlogs/%n-%d-%i.dump" called with a logging name of "Pok" could expand
# to something like "netlogs/Pok-Dec-20-01-1.dump" for the first instance and 
# "netlogs/Pok-Dec-20-01-2.%l" for the second logfile generated.
# %h/netlots/%n-%d-%i.dump could expand to
# /home/foo/netlogs/Pok-Dec-20-01-2.dump
#
# Other possibilities:  Sorting by directory
# logtemplate=%l/%n-%d-%i
# Would expand to, for example,
# dump/Pok-Dec-20-01-1
# crypt/Pok-Dec-20-01-1
# and so on.  The "dump", "crypt", etc, dirs must exist before kismet is run
# in this case.
logtemplate=%n-%d-%i.%l

# Where do we store the pid file of the server?
piddir=/var/run/

# Where state info, etc, is stored.  You shouldnt ever need to change this.
# This is a directory.
configdir=%h/.kismet/

# cloaked SSID file.  You shouldn't ever need to change this.
ssidmap=ssid_map

# Group map file.  You shouldn't ever need to change this.
groupmap=group_map

# IP range map file.  You shouldn't ever need to change this.
ipmap=ip_map