cris: add required patches

target/cris/qemu-cris/patches/4.6.4/crisv32_ethernet_driver.patch

@@ -0,0 +1,4050 @@
+diff -Nur linux-4.4.6.orig/arch/cris/arch-v32/drivers/Kconfig linux-4.4.6/arch/cris/arch-v32/drivers/Kconfig
+--- linux-4.4.6.orig/arch/cris/arch-v32/drivers/Kconfig	2016-03-16 16:43:17.000000000 +0100
++++ linux-4.4.6/arch/cris/arch-v32/drivers/Kconfig	2016-03-20 11:35:09.089964990 +0100
+@@ -8,9 +8,18 @@
+ 	  This option enables the ETRAX FS built-in 10/100Mbit Ethernet
+ 	  controller.
+ 
++config ETRAX_HAVE_PHY
++        bool "PHY present"
++	default y
++        help
++          Search and use the first PHY available on the MDIO bus. Fail
++          if none is found. Say Y here if you are not in a switched
++          environment (single port device).
++
+ config ETRAX_NO_PHY
+ 	bool "PHY not present"
+ 	depends on ETRAX_ETHERNET
++	default n
+ 	help
+ 	  This option disables all MDIO communication with an ethernet
+ 	  transceiver connected to the MII interface. This option shall
+@@ -18,6 +27,70 @@
+ 	  switch. This option should normally be disabled. If enabled,
+ 	  speed and duplex will be locked to 100 Mbit and full duplex.
+ 
++config ETRAX_PHY_FALLBACK
++        bool "Fixed PHY fallback"
++        depends on ETRAX_ETHERNET
++	default n
++        help
++          If no PHY is found on the MDIO bus, fall back on a fixed
++          100/Full fixed PHY. Say Y here if you need dynamic PHY
++          presence detection (switch connection where some but not
++          all ports have integrated PHYs), otherwise say N.
++
++config ETRAX_ETHERNET_IFACE0
++        depends on ETRAX_ETHERNET
++        bool "Enable network interface 0"
++
++config ETRAX_ETHERNET_IFACE1
++        depends on (ETRAX_ETHERNET && ETRAXFS)
++        bool "Enable network interface 1 (uses DMA6 and DMA7)"
++
++choice
++        prompt "Eth0 led group"
++        depends on ETRAX_ETHERNET_IFACE0
++        default ETRAX_ETH0_USE_LEDGRP0
++
++config ETRAX_ETH0_USE_LEDGRP0
++        bool "Use LED grp 0"
++        depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
++        help
++          Use LED grp 0 for eth0
++
++config ETRAX_ETH0_USE_LEDGRP1
++        bool "Use LED grp 1"
++        depends on ETRAX_NBR_LED_GRP_TWO
++        help
++          Use LED grp 1 for eth0
++
++config ETRAX_ETH0_USE_LEDGRPNULL
++        bool "Use no LEDs for eth0"
++        help
++          Use no LEDs for eth0
++endchoice
++
++choice
++        prompt "Eth1 led group"
++        depends on ETRAX_ETHERNET_IFACE1
++        default ETRAX_ETH1_USE_LEDGRP1
++
++config ETRAX_ETH1_USE_LEDGRP0
++        bool "Use LED grp 0"
++        depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
++        help
++          Use LED grp 0 for eth1
++
++config ETRAX_ETH1_USE_LEDGRP1
++        bool "Use LED grp 1"
++        depends on ETRAX_NBR_LED_GRP_TWO
++        help
++          Use LED grp 1 for eth1
++
++config ETRAX_ETH1_USE_LEDGRPNULL
++        bool "Use no LEDs for eth1"
++        help
++          Use no LEDs for eth1
++endchoice
++
+ config ETRAXFS_SERIAL
+ 	bool "Serial-port support"
+ 	depends on ETRAX_ARCH_V32
+diff -Nur linux-4.4.6.orig/arch/cris/include/arch-v32/arch/hwregs/eth_defs.h linux-4.4.6/arch/cris/include/arch-v32/arch/hwregs/eth_defs.h
+--- linux-4.4.6.orig/arch/cris/include/arch-v32/arch/hwregs/eth_defs.h	2016-03-16 16:43:17.000000000 +0100
++++ linux-4.4.6/arch/cris/include/arch-v32/arch/hwregs/eth_defs.h	2016-03-20 11:35:09.089964990 +0100
+@@ -2,69 +2,64 @@
+ #define __eth_defs_h
+ 
+ /*
+- * This file is autogenerated from
+- *   file:           eth.r
+- *     id:           eth_regs.r,v 1.16 2005/05/20 15:41:22 perz Exp
+- *     last modfied: Mon Jan  9 06:06:41 2006
+- *
+- *   by /n/asic/design/tools/rdesc/rdes2c eth.r
+- *      id: $Id: eth_defs.h,v 1.7 2006/01/26 13:45:30 karljope Exp $
+- * Any changes here will be lost.
+- *
+- * -*- buffer-read-only: t -*-
++ * Note: Previously this was autogenerated code from the hardware
++ * implementation. However, to enable the same file to be used
++ * for both ARTPEC-3 and ETRAX FS this file is now hand-edited.
++ * Be careful.
+  */
++
+ /* Main access macros */
+ #ifndef REG_RD
+ #define REG_RD( scope, inst, reg ) \
+-  REG_READ( reg_##scope##_##reg, \
+-            (inst) + REG_RD_ADDR_##scope##_##reg )
++	REG_READ( reg_##scope##_##reg, \
++			(inst) + REG_RD_ADDR_##scope##_##reg )
+ #endif
+ 
+ #ifndef REG_WR
+ #define REG_WR( scope, inst, reg, val ) \
+-  REG_WRITE( reg_##scope##_##reg, \
+-             (inst) + REG_WR_ADDR_##scope##_##reg, (val) )
++	REG_WRITE( reg_##scope##_##reg, \
++			(inst) + REG_WR_ADDR_##scope##_##reg, (val) )
+ #endif
+ 
+ #ifndef REG_RD_VECT
+ #define REG_RD_VECT( scope, inst, reg, index ) \
+-  REG_READ( reg_##scope##_##reg, \
+-            (inst) + REG_RD_ADDR_##scope##_##reg + \
+-	    (index) * STRIDE_##scope##_##reg )
++	REG_READ( reg_##scope##_##reg, \
++			(inst) + REG_RD_ADDR_##scope##_##reg + \
++			(index) * STRIDE_##scope##_##reg )
+ #endif
+ 
+ #ifndef REG_WR_VECT
+ #define REG_WR_VECT( scope, inst, reg, index, val ) \
+-  REG_WRITE( reg_##scope##_##reg, \
+-             (inst) + REG_WR_ADDR_##scope##_##reg + \
+-	     (index) * STRIDE_##scope##_##reg, (val) )
++	REG_WRITE( reg_##scope##_##reg, \
++			(inst) + REG_WR_ADDR_##scope##_##reg + \
++			(index) * STRIDE_##scope##_##reg, (val) )
+ #endif
+ 
+ #ifndef REG_RD_INT
+ #define REG_RD_INT( scope, inst, reg ) \
+-  REG_READ( int, (inst) + REG_RD_ADDR_##scope##_##reg )
++	REG_READ( int, (inst) + REG_RD_ADDR_##scope##_##reg )
+ #endif
+ 
+ #ifndef REG_WR_INT
+ #define REG_WR_INT( scope, inst, reg, val ) \
+-  REG_WRITE( int, (inst) + REG_WR_ADDR_##scope##_##reg, (val) )
++	REG_WRITE( int, (inst) + REG_WR_ADDR_##scope##_##reg, (val) )
+ #endif
+ 
+ #ifndef REG_RD_INT_VECT
+ #define REG_RD_INT_VECT( scope, inst, reg, index ) \
+-  REG_READ( int, (inst) + REG_RD_ADDR_##scope##_##reg + \
+-	    (index) * STRIDE_##scope##_##reg )
++	REG_READ( int, (inst) + REG_RD_ADDR_##scope##_##reg + \
++			(index) * STRIDE_##scope##_##reg )
+ #endif
+ 
+ #ifndef REG_WR_INT_VECT
+ #define REG_WR_INT_VECT( scope, inst, reg, index, val ) \
+-  REG_WRITE( int, (inst) + REG_WR_ADDR_##scope##_##reg + \
+-	     (index) * STRIDE_##scope##_##reg, (val) )
++	REG_WRITE( int, (inst) + REG_WR_ADDR_##scope##_##reg + \
++			(index) * STRIDE_##scope##_##reg, (val) )
+ #endif
+ 
+ #ifndef REG_TYPE_CONV
+ #define REG_TYPE_CONV( type, orgtype, val ) \
+-  ( { union { orgtype o; type n; } r; r.o = val; r.n; } )
++	( { union { orgtype o; type n; } r; r.o = val; r.n; } )
+ #endif
+ 
+ #ifndef reg_page_size
+@@ -73,306 +68,332 @@
+ 
+ #ifndef REG_ADDR
+ #define REG_ADDR( scope, inst, reg ) \
+-  ( (inst) + REG_RD_ADDR_##scope##_##reg )
++	( (inst) + REG_RD_ADDR_##scope##_##reg )
+ #endif
+ 
+ #ifndef REG_ADDR_VECT
+ #define REG_ADDR_VECT( scope, inst, reg, index ) \
+-  ( (inst) + REG_RD_ADDR_##scope##_##reg + \
+-    (index) * STRIDE_##scope##_##reg )
++	( (inst) + REG_RD_ADDR_##scope##_##reg + \
++	  (index) * STRIDE_##scope##_##reg )
+ #endif
+ 
+ /* C-code for register scope eth */
+ 
+ /* Register rw_ma0_lo, scope eth, type rw */
+ typedef struct {
+-  unsigned int addr : 32;
++	unsigned int addr : 32;
+ } reg_eth_rw_ma0_lo;
+ #define REG_RD_ADDR_eth_rw_ma0_lo 0
+ #define REG_WR_ADDR_eth_rw_ma0_lo 0
+ 
+ /* Register rw_ma0_hi, scope eth, type rw */
+ typedef struct {
+-  unsigned int addr : 16;
+-  unsigned int dummy1 : 16;
++	unsigned int addr : 16;
++	unsigned int dummy1 : 16;
+ } reg_eth_rw_ma0_hi;
+ #define REG_RD_ADDR_eth_rw_ma0_hi 4
+ #define REG_WR_ADDR_eth_rw_ma0_hi 4
+ 
+ /* Register rw_ma1_lo, scope eth, type rw */
+ typedef struct {
+-  unsigned int addr : 32;
++	unsigned int addr : 32;
+ } reg_eth_rw_ma1_lo;
+ #define REG_RD_ADDR_eth_rw_ma1_lo 8
+ #define REG_WR_ADDR_eth_rw_ma1_lo 8
+ 
+ /* Register rw_ma1_hi, scope eth, type rw */
+ typedef struct {
+-  unsigned int addr : 16;
+-  unsigned int dummy1 : 16;
++	unsigned int addr : 16;
++	unsigned int dummy1 : 16;
+ } reg_eth_rw_ma1_hi;
+ #define REG_RD_ADDR_eth_rw_ma1_hi 12
+ #define REG_WR_ADDR_eth_rw_ma1_hi 12
+ 
+ /* Register rw_ga_lo, scope eth, type rw */
+ typedef struct {
+-  unsigned int tbl : 32;
++	unsigned int table : 32;
+ } reg_eth_rw_ga_lo;
+ #define REG_RD_ADDR_eth_rw_ga_lo 16
+ #define REG_WR_ADDR_eth_rw_ga_lo 16
+ 
+ /* Register rw_ga_hi, scope eth, type rw */
+ typedef struct {
+-  unsigned int tbl : 32;
++	unsigned int table : 32;
+ } reg_eth_rw_ga_hi;
+ #define REG_RD_ADDR_eth_rw_ga_hi 20
+ #define REG_WR_ADDR_eth_rw_ga_hi 20
+ 
+ /* Register rw_gen_ctrl, scope eth, type rw */
+ typedef struct {
+-  unsigned int en         : 1;
+-  unsigned int phy        : 2;
+-  unsigned int protocol   : 1;
+-  unsigned int loopback   : 1;
+-  unsigned int flow_ctrl  : 1;
+-  unsigned int gtxclk_out : 1;
+-  unsigned int phyrst_n   : 1;
+-  unsigned int dummy1     : 24;
++	unsigned int en         : 1;
++	unsigned int phy        : 2;
++	unsigned int protocol   : 1;
++	unsigned int loopback   : 1;
++	unsigned int flow_ctrl  : 1;
++	unsigned int gtxclk_out : 1;
++	unsigned int phyrst_n   : 1;
++	unsigned int dummy1     : 24;
+ } reg_eth_rw_gen_ctrl;
+ #define REG_RD_ADDR_eth_rw_gen_ctrl 24
+ #define REG_WR_ADDR_eth_rw_gen_ctrl 24
+ 
+ /* Register rw_rec_ctrl, scope eth, type rw */
+ typedef struct {
+-  unsigned int ma0        : 1;
+-  unsigned int ma1        : 1;
+-  unsigned int individual : 1;
+-  unsigned int broadcast  : 1;
+-  unsigned int undersize  : 1;
+-  unsigned int oversize   : 1;
+-  unsigned int bad_crc    : 1;
+-  unsigned int duplex     : 1;
+-  unsigned int max_size   : 16;
+-  unsigned int dummy1     : 8;
++	unsigned int ma0        : 1;
++	unsigned int ma1        : 1;
++	unsigned int individual : 1;
++	unsigned int broadcast  : 1;
++	unsigned int undersize  : 1;
++	unsigned int oversize   : 1;
++	unsigned int bad_crc    : 1;
++	unsigned int duplex     : 1;
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	unsigned int max_size   : 16;
++	unsigned int dummy1     : 8;
++#else
++	unsigned int max_size   : 1;
++	unsigned int dummy1     : 23;
++#endif
+ } reg_eth_rw_rec_ctrl;
+ #define REG_RD_ADDR_eth_rw_rec_ctrl 28
+ #define REG_WR_ADDR_eth_rw_rec_ctrl 28
+ 
+ /* Register rw_tr_ctrl, scope eth, type rw */
+ typedef struct {
+-  unsigned int crc         : 1;
+-  unsigned int pad         : 1;
+-  unsigned int retry       : 1;
+-  unsigned int ignore_col  : 1;
+-  unsigned int cancel      : 1;
+-  unsigned int hsh_delay   : 1;
+-  unsigned int ignore_crs  : 1;
+-  unsigned int carrier_ext : 1;
+-  unsigned int dummy1      : 24;
++	unsigned int crc         : 1;
++	unsigned int pad         : 1;
++	unsigned int retry       : 1;
++	unsigned int ignore_col  : 1;
++	unsigned int cancel      : 1;
++	unsigned int hsh_delay   : 1;
++	unsigned int ignore_crs  : 1;
++	unsigned int carrier_ext : 1;
++	unsigned int dummy1      : 24;
+ } reg_eth_rw_tr_ctrl;
+ #define REG_RD_ADDR_eth_rw_tr_ctrl 32
+ #define REG_WR_ADDR_eth_rw_tr_ctrl 32
+ 
+ /* Register rw_clr_err, scope eth, type rw */
+ typedef struct {
+-  unsigned int clr : 1;
+-  unsigned int dummy1 : 31;
++	unsigned int clr : 1;
++	unsigned int dummy1 : 31;
+ } reg_eth_rw_clr_err;
+ #define REG_RD_ADDR_eth_rw_clr_err 36
+ #define REG_WR_ADDR_eth_rw_clr_err 36
+ 
+ /* Register rw_mgm_ctrl, scope eth, type rw */
+ typedef struct {
+-  unsigned int mdio : 1;
+-  unsigned int mdoe : 1;
+-  unsigned int mdc  : 1;
+-  unsigned int dummy1 : 29;
++	unsigned int mdio : 1;
++	unsigned int mdoe : 1;
++	unsigned int mdc  : 1;
++	unsigned int phyclk : 1;
++	unsigned int txdata : 4;
++	unsigned int txen   : 1;
++	unsigned int dummy1 : 23;
+ } reg_eth_rw_mgm_ctrl;
+ #define REG_RD_ADDR_eth_rw_mgm_ctrl 40
+ #define REG_WR_ADDR_eth_rw_mgm_ctrl 40
+ 
+ /* Register r_stat, scope eth, type r */
+ typedef struct {
+-  unsigned int mdio    : 1;
+-  unsigned int exc_col : 1;
+-  unsigned int urun    : 1;
+-  unsigned int clk_125 : 1;
+-  unsigned int dummy1  : 28;
++	unsigned int mdio    : 1;
++	unsigned int exc_col : 1;
++	unsigned int urun    : 1;
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	unsigned int clk_125 : 1;
++#else
++	unsigned int phyclk  : 1;
++#endif
++	unsigned int txdata  : 4;
++	unsigned int txen    : 1;
++	unsigned int col     : 1;
++	unsigned int crs     : 1;
++	unsigned int txclk   : 1;
++	unsigned int rxdata  : 4;
++	unsigned int rxer    : 1;
++	unsigned int rxdv    : 1;
++	unsigned int rxclk   : 1;
++	unsigned int dummy1  : 13;
+ } reg_eth_r_stat;
+ #define REG_RD_ADDR_eth_r_stat 44
+ 
+ /* Register rs_rec_cnt, scope eth, type rs */
+ typedef struct {
+-  unsigned int crc_err    : 8;
+-  unsigned int align_err  : 8;
+-  unsigned int oversize   : 8;
+-  unsigned int congestion : 8;
++	unsigned int crc_err    : 8;
++	unsigned int align_err  : 8;
++	unsigned int oversize   : 8;
++	unsigned int congestion : 8;
+ } reg_eth_rs_rec_cnt;
+ #define REG_RD_ADDR_eth_rs_rec_cnt 48
+ 
+ /* Register r_rec_cnt, scope eth, type r */
+ typedef struct {
+-  unsigned int crc_err    : 8;
+-  unsigned int align_err  : 8;
+-  unsigned int oversize   : 8;
+-  unsigned int congestion : 8;
++	unsigned int crc_err    : 8;
++	unsigned int align_err  : 8;
++	unsigned int oversize   : 8;
++	unsigned int congestion : 8;
+ } reg_eth_r_rec_cnt;
+ #define REG_RD_ADDR_eth_r_rec_cnt 52
+ 
+ /* Register rs_tr_cnt, scope eth, type rs */
+ typedef struct {
+-  unsigned int single_col : 8;
+-  unsigned int mult_col   : 8;
+-  unsigned int late_col   : 8;
+-  unsigned int deferred   : 8;
++	unsigned int single_col : 8;
++	unsigned int mult_col   : 8;
++	unsigned int late_col   : 8;
++	unsigned int deferred   : 8;
+ } reg_eth_rs_tr_cnt;
+ #define REG_RD_ADDR_eth_rs_tr_cnt 56
+ 
+ /* Register r_tr_cnt, scope eth, type r */
+ typedef struct {
+-  unsigned int single_col : 8;
+-  unsigned int mult_col   : 8;
+-  unsigned int late_col   : 8;
+-  unsigned int deferred   : 8;
++	unsigned int single_col : 8;
++	unsigned int mult_col   : 8;
++	unsigned int late_col   : 8;
++	unsigned int deferred   : 8;
+ } reg_eth_r_tr_cnt;
+ #define REG_RD_ADDR_eth_r_tr_cnt 60
+ 
+ /* Register rs_phy_cnt, scope eth, type rs */
+ typedef struct {
+-  unsigned int carrier_loss : 8;
+-  unsigned int sqe_err      : 8;
+-  unsigned int dummy1       : 16;
++	unsigned int carrier_loss : 8;
++	unsigned int sqe_err      : 8;
++	unsigned int dummy1       : 16;
+ } reg_eth_rs_phy_cnt;
+ #define REG_RD_ADDR_eth_rs_phy_cnt 64
+ 
+ /* Register r_phy_cnt, scope eth, type r */
+ typedef struct {
+-  unsigned int carrier_loss : 8;
+-  unsigned int sqe_err      : 8;
+-  unsigned int dummy1       : 16;
++	unsigned int carrier_loss : 8;
++	unsigned int sqe_err      : 8;
++	unsigned int dummy1       : 16;
+ } reg_eth_r_phy_cnt;
+ #define REG_RD_ADDR_eth_r_phy_cnt 68
+ 
+ /* Register rw_test_ctrl, scope eth, type rw */
+ typedef struct {
+-  unsigned int snmp_inc : 1;
+-  unsigned int snmp     : 1;
+-  unsigned int backoff  : 1;
+-  unsigned int dummy1   : 29;
++	unsigned int snmp_inc : 1;
++	unsigned int snmp     : 1;
++	unsigned int backoff  : 1;
++	unsigned int dummy1   : 29;
+ } reg_eth_rw_test_ctrl;
+ #define REG_RD_ADDR_eth_rw_test_ctrl 72
+ #define REG_WR_ADDR_eth_rw_test_ctrl 72
+ 
+ /* Register rw_intr_mask, scope eth, type rw */
+ typedef struct {
+-  unsigned int crc          : 1;
+-  unsigned int align        : 1;
+-  unsigned int oversize     : 1;
+-  unsigned int congestion   : 1;
+-  unsigned int single_col   : 1;
+-  unsigned int mult_col     : 1;
+-  unsigned int late_col     : 1;
+-  unsigned int deferred     : 1;
+-  unsigned int carrier_loss : 1;
+-  unsigned int sqe_test_err : 1;
+-  unsigned int orun         : 1;
+-  unsigned int urun         : 1;
+-  unsigned int exc_col      : 1;
+-  unsigned int mdio         : 1;
+-  unsigned int dummy1       : 18;
++	unsigned int crc          : 1;
++	unsigned int align        : 1;
++	unsigned int oversize     : 1;
++	unsigned int congestion   : 1;
++	unsigned int single_col   : 1;
++	unsigned int mult_col     : 1;
++	unsigned int late_col     : 1;
++	unsigned int deferred     : 1;
++	unsigned int carrier_loss : 1;
++	unsigned int sqe_test_err : 1;
++	unsigned int orun         : 1;
++	unsigned int urun         : 1;
++	unsigned int exc_col      : 1;
++	unsigned int mdio         : 1;
++	unsigned int dummy1       : 18;
+ } reg_eth_rw_intr_mask;
+ #define REG_RD_ADDR_eth_rw_intr_mask 76
+ #define REG_WR_ADDR_eth_rw_intr_mask 76
+ 
+ /* Register rw_ack_intr, scope eth, type rw */
+ typedef struct {
+-  unsigned int crc          : 1;
+-  unsigned int align        : 1;
+-  unsigned int oversize     : 1;
+-  unsigned int congestion   : 1;
+-  unsigned int single_col   : 1;
+-  unsigned int mult_col     : 1;
+-  unsigned int late_col     : 1;
+-  unsigned int deferred     : 1;
+-  unsigned int carrier_loss : 1;
+-  unsigned int sqe_test_err : 1;
+-  unsigned int orun         : 1;
+-  unsigned int urun         : 1;
+-  unsigned int exc_col      : 1;
+-  unsigned int mdio         : 1;
+-  unsigned int dummy1       : 18;
++	unsigned int crc          : 1;
++	unsigned int align        : 1;
++	unsigned int oversize     : 1;
++	unsigned int congestion   : 1;
++	unsigned int single_col   : 1;
++	unsigned int mult_col     : 1;
++	unsigned int late_col     : 1;
++	unsigned int deferred     : 1;
++	unsigned int carrier_loss : 1;
++	unsigned int sqe_test_err : 1;
++	unsigned int orun         : 1;
++	unsigned int urun         : 1;
++	unsigned int exc_col      : 1;
++	unsigned int mdio         : 1;
++	unsigned int dummy1       : 18;
+ } reg_eth_rw_ack_intr;
+ #define REG_RD_ADDR_eth_rw_ack_intr 80
+ #define REG_WR_ADDR_eth_rw_ack_intr 80
+ 
+ /* Register r_intr, scope eth, type r */
+ typedef struct {
+-  unsigned int crc          : 1;
+-  unsigned int align        : 1;
+-  unsigned int oversize     : 1;
+-  unsigned int congestion   : 1;
+-  unsigned int single_col   : 1;
+-  unsigned int mult_col     : 1;
+-  unsigned int late_col     : 1;
+-  unsigned int deferred     : 1;
+-  unsigned int carrier_loss : 1;
+-  unsigned int sqe_test_err : 1;
+-  unsigned int orun         : 1;
+-  unsigned int urun         : 1;
+-  unsigned int exc_col      : 1;
+-  unsigned int mdio         : 1;
+-  unsigned int dummy1       : 18;
++	unsigned int crc          : 1;
++	unsigned int align        : 1;
++	unsigned int oversize     : 1;
++	unsigned int congestion   : 1;
++	unsigned int single_col   : 1;
++	unsigned int mult_col     : 1;
++	unsigned int late_col     : 1;
++	unsigned int deferred     : 1;
++	unsigned int carrier_loss : 1;
++	unsigned int sqe_test_err : 1;
++	unsigned int orun         : 1;
++	unsigned int urun         : 1;
++	unsigned int exc_col      : 1;
++	unsigned int mdio         : 1;
++	unsigned int dummy1       : 18;
+ } reg_eth_r_intr;
+ #define REG_RD_ADDR_eth_r_intr 84
+ 
+ /* Register r_masked_intr, scope eth, type r */
+ typedef struct {
+-  unsigned int crc          : 1;
+-  unsigned int align        : 1;
+-  unsigned int oversize     : 1;
+-  unsigned int congestion   : 1;
+-  unsigned int single_col   : 1;
+-  unsigned int mult_col     : 1;
+-  unsigned int late_col     : 1;
+-  unsigned int deferred     : 1;
+-  unsigned int carrier_loss : 1;
+-  unsigned int sqe_test_err : 1;
+-  unsigned int orun         : 1;
+-  unsigned int urun         : 1;
+-  unsigned int exc_col      : 1;
+-  unsigned int mdio         : 1;
+-  unsigned int dummy1       : 18;
++	unsigned int crc          : 1;
++	unsigned int align        : 1;
++	unsigned int oversize     : 1;
++	unsigned int congestion   : 1;
++	unsigned int single_col   : 1;
++	unsigned int mult_col     : 1;
++	unsigned int late_col     : 1;
++	unsigned int deferred     : 1;
++	unsigned int carrier_loss : 1;
++	unsigned int sqe_test_err : 1;
++	unsigned int orun         : 1;
++	unsigned int urun         : 1;
++	unsigned int exc_col      : 1;
++	unsigned int mdio         : 1;
++	unsigned int dummy1       : 18;
+ } reg_eth_r_masked_intr;
+ #define REG_RD_ADDR_eth_r_masked_intr 88
+ 
+-
+ /* Constants */
+ enum {
+-  regk_eth_discard                         = 0x00000000,
+-  regk_eth_ether                           = 0x00000000,
+-  regk_eth_full                            = 0x00000001,
+-  regk_eth_gmii                            = 0x00000003,
+-  regk_eth_gtxclk                          = 0x00000001,
+-  regk_eth_half                            = 0x00000000,
+-  regk_eth_hsh                             = 0x00000001,
+-  regk_eth_mii                             = 0x00000001,
+-  regk_eth_mii_arec                        = 0x00000002,
+-  regk_eth_mii_clk                         = 0x00000000,
+-  regk_eth_no                              = 0x00000000,
+-  regk_eth_phyrst                          = 0x00000000,
+-  regk_eth_rec                             = 0x00000001,
+-  regk_eth_rw_ga_hi_default                = 0x00000000,
+-  regk_eth_rw_ga_lo_default                = 0x00000000,
+-  regk_eth_rw_gen_ctrl_default             = 0x00000000,
+-  regk_eth_rw_intr_mask_default            = 0x00000000,
+-  regk_eth_rw_ma0_hi_default               = 0x00000000,
+-  regk_eth_rw_ma0_lo_default               = 0x00000000,
+-  regk_eth_rw_ma1_hi_default               = 0x00000000,
+-  regk_eth_rw_ma1_lo_default               = 0x00000000,
+-  regk_eth_rw_mgm_ctrl_default             = 0x00000000,
+-  regk_eth_rw_test_ctrl_default            = 0x00000000,
+-  regk_eth_size1518                        = 0x000005ee,
+-  regk_eth_size1522                        = 0x000005f2,
+-  regk_eth_yes                             = 0x00000001
++	regk_eth_discard                         = 0x00000000,
++	regk_eth_ether                           = 0x00000000,
++	regk_eth_full                            = 0x00000001,
++	regk_eth_gmii                            = 0x00000003,
++	regk_eth_gtxclk                          = 0x00000001,
++	regk_eth_half                            = 0x00000000,
++	regk_eth_hsh                             = 0x00000001,
++	regk_eth_mii                             = 0x00000001,
++	regk_eth_mii_arec                        = 0x00000002,
++	regk_eth_mii_clk                         = 0x00000000,
++	regk_eth_no                              = 0x00000000,
++	regk_eth_phyrst                          = 0x00000000,
++	regk_eth_rec                             = 0x00000001,
++	regk_eth_rw_ga_hi_default                = 0x00000000,
++	regk_eth_rw_ga_lo_default                = 0x00000000,
++	regk_eth_rw_gen_ctrl_default             = 0x00000000,
++	regk_eth_rw_intr_mask_default            = 0x00000000,
++	regk_eth_rw_ma0_hi_default               = 0x00000000,
++	regk_eth_rw_ma0_lo_default               = 0x00000000,
++	regk_eth_rw_ma1_hi_default               = 0x00000000,
++	regk_eth_rw_ma1_lo_default               = 0x00000000,
++	regk_eth_rw_mgm_ctrl_default             = 0x00000000,
++	regk_eth_rw_test_ctrl_default            = 0x00000000,
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	regk_eth_size1518                        = 0x000005ee,
++	regk_eth_size1522                        = 0x000005f2,
++#else
++	regk_eth_size1518                        = 0x00000000,
++	regk_eth_size1522                        = 0x00000001,
++#endif
++	regk_eth_yes                             = 0x00000001
+ };
++
+ #endif /* __eth_defs_h */
+diff -Nur linux-4.4.6.orig/drivers/net/cris/eth_v32.c linux-4.4.6/drivers/net/cris/eth_v32.c
+--- linux-4.4.6.orig/drivers/net/cris/eth_v32.c	1970-01-01 01:00:00.000000000 +0100
++++ linux-4.4.6/drivers/net/cris/eth_v32.c	2016-03-20 15:09:58.183871830 +0100
+@@ -0,0 +1,3062 @@
++/*
++ * Driver for the ETRAX FS/Artpec-3 network controller.
++ *
++ * Copyright (c) 2003-2008 Axis Communications AB.
++ *
++ * TODO:
++ *   *    Decrease the amount of code running with interrupts disabled.
++ *   *    Rework the error handling so that we do not need to touch the tx
++ *        ring from the error interrupts. When done, we should be able to
++ *        do tx completition from the NAPI loop without disabling interrupts.
++ *   *    Remove the gigabit code. It's probably never going to be used.
++ */
++
++#include <linux/module.h>
++
++#include <linux/kernel.h>
++#include <linux/sched.h>
++#include <linux/delay.h>
++#include <linux/types.h>
++#include <linux/fcntl.h>
++#include <linux/interrupt.h>
++#include <linux/spinlock.h>
++#include <linux/errno.h>
++#include <linux/init.h>
++
++#include <linux/netdevice.h>
++#include <linux/etherdevice.h>
++#include <linux/skbuff.h>
++#include <linux/ethtool.h>
++#include <linux/mii.h>
++
++#include <asm/io.h>		/* CRIS_LED_* I/O functions */
++#include <asm/irq.h>
++#include <hwregs/reg_map.h>
++#include <hwregs/reg_rdwr.h>
++#include <hwregs/dma.h>
++#include <hwregs/eth_defs.h>
++#ifdef CONFIG_ETRAXFS
++#include <hwregs/config_defs.h>
++#else
++#include <hwregs/clkgen_defs.h>
++#endif
++#include <hwregs/intr_vect_defs.h>
++#include <hwregs/strmux_defs.h>
++#include <asm/bitops.h>
++#include <asm/ethernet.h>
++#include <mach/dma.h>
++#include <pinmux.h>
++
++#include "eth_v32.h"
++
++#ifndef CONFIG_ETRAXFS
++#define ETH0_INTR_VECT ETH_INTR_VECT
++#define ETH1_INTR_VECT ETH_INTR_VECT
++#define regi_eth0 regi_eth
++#define regi_eth1 regi_
++#endif
++
++#define DEBUG(x)
++#define GET_BIT(bit,val)   (((val) >> (bit)) & 0x01)
++
++#if defined(CONFIG_ETRAX_HAVE_PHY) || defined(CONFIG_ETRAX_PHY_FALLBACK)
++#define RESET_PHY 1
++#else
++#define RESET_PHY 0
++#endif
++
++enum {
++	HAVE_PHY,
++	NO_PHY,
++	FALLBACK_PHY,
++};
++#if defined(CONFIG_ETRAX_PHY_FALLBACK)
++#define PHY_MODE (FALLBACK_PHY)
++#elif defined(CONFIG_ETRAX_NO_PHY)
++#define PHY_MODE (NO_PHY)
++#elif defined(CONFIG_ETRAX_HAVE_PHY)
++#define PHY_MODE (HAVE_PHY)
++#else
++#error Unknown PHY behaviour
++#endif
++
++static struct {
++	const char str[ETH_GSTRING_LEN];
++} const ethtool_stats_keys[] = {
++	{ "tx_dma_restarts" },
++	{ "tx_mac_resets" },
++	{ "rx_dma_restarts" },
++	{ "rx_dma_timeouts" },
++	{ "  dropped_rx" }
++};
++
++static void crisv32_eth_check_speed(unsigned long idev);
++static void crisv32_eth_check_duplex(unsigned long idev);
++static void update_rx_stats(struct crisv32_ethernet_local *np);
++static void update_tx_stats(struct crisv32_ethernet_local *np);
++static int crisv32_eth_poll(struct napi_struct *napi, int budget);
++static void crisv32_eth_setup_controller(struct net_device *dev);
++static int crisv32_eth_request_irqdma(struct net_device *dev);
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++static void
++crisv32_eth_restart_rx_dma(struct net_device* dev,
++			   struct crisv32_ethernet_local *np);
++#endif
++#if 0
++static void crisv32_ethernet_bug(struct net_device *dev);
++#endif
++
++/*
++ * The name of the card. Is used for messages and in the requests for
++ * io regions, irqs and dma channels.
++ */
++#ifdef CONFIG_ETRAXFS
++static const char cardname[] = "ETRAX FS built-in ethernet controller";
++#else
++static const char cardname[] = "ARTPEC-3 built-in ethernet controller";
++#endif
++
++/* Some chipset needs special care. */
++#ifndef CONFIG_ETRAX_NO_PHY
++struct transceiver_ops transceivers[] = {
++	{0x1018, broadcom_check_speed, broadcom_check_duplex},
++	{0x50EF, broadcom_check_speed, broadcom_check_duplex},
++	/* TDK 2120 and TDK 2120C */
++	{0xC039, tdk_check_speed, tdk_check_duplex},
++	{0x039C, tdk_check_speed, tdk_check_duplex},
++	/* Intel LXT972A*/
++	{0x04de, intel_check_speed, intel_check_duplex},
++	/* National Semiconductor DP83865 */
++	{0x0017, national_check_speed, national_check_duplex},
++	/* Vitesse VCS8641 */
++	{0x01c1, vitesse_check_speed, vitesse_check_duplex},
++	/* Davicom DM9161 */
++	{0x606E, davicom_check_speed, davicom_check_duplex},
++	/* Generic, must be last. */
++	{0x0000, generic_check_speed, generic_check_duplex}
++};
++#endif
++
++static struct net_device *crisv32_dev[2];
++static struct crisv32_eth_leds *crisv32_leds[3];
++
++/* Default MAC address for interface 0.
++ * The real one will be set later. */
++static struct sockaddr default_mac_iface0 =
++  {0, {0x00, 0x40, 0x8C, 0xCD, 0x00, 0x00}};
++
++#ifdef CONFIG_CPU_FREQ
++static int
++crisv32_ethernet_freq_notifier(struct notifier_block *nb, unsigned long val,
++			       void *data);
++
++static struct notifier_block crisv32_ethernet_freq_notifier_block = {
++	.notifier_call	= crisv32_ethernet_freq_notifier
++};
++#endif
++
++static void receive_timeout(unsigned long arg);
++static void receive_timeout_work(struct work_struct* work);
++static void transmit_timeout(unsigned long arg);
++
++/*
++ * mask in and out tx/rx interrupts.
++ */
++static inline void crisv32_disable_tx_ints(struct crisv32_ethernet_local *np)
++{
++	reg_dma_rw_intr_mask intr_mask_tx = { .data = regk_dma_no };
++	REG_WR(dma, np->dma_out_inst, rw_intr_mask, intr_mask_tx);
++}
++
++static inline void crisv32_enable_tx_ints(struct crisv32_ethernet_local *np)
++{
++	reg_dma_rw_intr_mask intr_mask_tx = { .data = regk_dma_yes };
++	REG_WR(dma, np->dma_out_inst, rw_intr_mask, intr_mask_tx);
++}
++
++static inline void crisv32_disable_rx_ints(struct crisv32_ethernet_local *np)
++{
++	reg_dma_rw_intr_mask intr_mask_rx = { .in_eop = regk_dma_no };
++	REG_WR(dma, np->dma_in_inst, rw_intr_mask, intr_mask_rx);
++}
++
++static inline void crisv32_enable_rx_ints(struct crisv32_ethernet_local *np)
++{
++	reg_dma_rw_intr_mask intr_mask_rx = { .in_eop = regk_dma_yes };
++	REG_WR(dma, np->dma_in_inst, rw_intr_mask, intr_mask_rx);
++}
++
++static inline void crisv32_disable_eth_ints(struct crisv32_ethernet_local *np)
++{
++	int intr_mask_nw = 0x0;
++	REG_WR_INT(eth, np->eth_inst, rw_intr_mask, intr_mask_nw);
++}
++
++static inline void crisv32_enable_eth_ints(struct crisv32_ethernet_local *np)
++{
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	/* For Artpec-3 we use overrun to workaround voodoo TR 87 */
++	int intr_mask_nw = 0x1c00;
++#else
++	int intr_mask_nw = 0x1800;
++#endif
++	REG_WR_INT(eth, np->eth_inst, rw_intr_mask, intr_mask_nw);
++}
++
++static inline int crisv32_eth_gigabit(struct crisv32_ethernet_local *np)
++{
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	return np->gigabit_mode;
++#else
++	return 0;
++#endif
++}
++
++static inline void crisv32_eth_set_gigabit(struct crisv32_ethernet_local *np,
++					   int g)
++{
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	np->gigabit_mode = g;
++#endif
++}
++
++/* start/stop receiver */
++static inline void crisv32_start_receiver(struct crisv32_ethernet_local *np)
++{
++	reg_eth_rw_rec_ctrl rec_ctrl;
++
++	rec_ctrl = REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++	rec_ctrl.ma0 = regk_eth_yes;
++	rec_ctrl.broadcast = regk_eth_rec;
++	REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++}
++
++static inline void crisv32_stop_receiver(struct crisv32_ethernet_local *np)
++{
++	reg_eth_rw_rec_ctrl rec_ctrl;
++
++	rec_ctrl = REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++	rec_ctrl.ma0 = regk_eth_no;
++	rec_ctrl.broadcast = regk_eth_discard;
++	REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++}
++
++static inline void crisv32_eth_reset(struct crisv32_ethernet_local *np)
++{
++	reg_eth_rw_gen_ctrl gen_ctrl = { 0 };
++
++	gen_ctrl = REG_RD(eth, np->eth_inst, rw_gen_ctrl);
++	gen_ctrl.en = regk_eth_no;
++	REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl);
++	gen_ctrl.en = regk_eth_yes;
++	REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl);
++}
++
++static void crisv32_eth_tx_cancel_frame(struct crisv32_ethernet_local *np)
++{
++	reg_eth_rw_tr_ctrl tr_ctrl;
++
++	/* Cancel any pending transmits.  This should bring us to the
++	   excessive collisions state but it doesn't always do it.  */
++	tr_ctrl = REG_RD(eth, np->eth_inst, rw_tr_ctrl);
++	tr_ctrl.cancel = 1;
++	REG_WR(eth, np->eth_inst, rw_tr_ctrl, tr_ctrl);
++	tr_ctrl.cancel = 0;
++	REG_WR(eth, np->eth_inst, rw_tr_ctrl, tr_ctrl);
++}
++
++/*
++ * Hack to disconnect/reconnect the dma from the ethernet block while we reset
++ * things. TODO: verify that we don't need to disconnect out channels and
++ * remove that code.
++ *
++ * ARTPEC-3 has only a single ethernet block so np->eth_inst is always eth0.
++ * The strmux values are named slightly different, redefine to avoid #ifdefs
++ * in the code blocks. For artpec3 only regk_strmux_eth0 and channel 0/1
++ * should be used.
++ */
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++#define regk_strmux_eth0 regk_strmux_eth
++#define regk_strmux_eth1 regk_strmux_eth
++#endif
++static inline void
++crisv32_disconnect_eth_tx_dma(struct crisv32_ethernet_local *np)
++{
++	reg_strmux_rw_cfg strmux_cfg;
++
++	strmux_cfg = REG_RD(strmux, regi_strmux, rw_cfg);
++	if (np->eth_inst == regi_eth0)
++		strmux_cfg.dma0 = regk_strmux_off;
++	else
++		strmux_cfg.dma6 = regk_strmux_off;
++	REG_WR(strmux, regi_strmux, rw_cfg, strmux_cfg);
++}
++
++static inline void crisv32_connect_eth_tx_dma(struct crisv32_ethernet_local *np)
++{
++	reg_strmux_rw_cfg strmux_cfg;
++
++	strmux_cfg = REG_RD(strmux, regi_strmux, rw_cfg);
++	if (np->eth_inst == regi_eth0)
++		strmux_cfg.dma0 = regk_strmux_eth0;
++	else
++		strmux_cfg.dma6 = regk_strmux_eth1;
++	REG_WR(strmux, regi_strmux, rw_cfg, strmux_cfg);
++}
++
++static inline void
++crisv32_disconnect_eth_rx_dma(struct crisv32_ethernet_local *np)
++{
++	reg_strmux_rw_cfg strmux_cfg;
++
++	strmux_cfg = REG_RD(strmux, regi_strmux, rw_cfg);
++	if (np->eth_inst == regi_eth0)
++		strmux_cfg.dma1 = regk_strmux_off;
++	else
++		strmux_cfg.dma7 = regk_strmux_off;
++	REG_WR(strmux, regi_strmux, rw_cfg, strmux_cfg);
++}
++
++static inline void crisv32_connect_eth_rx_dma(struct crisv32_ethernet_local *np)
++{
++	reg_strmux_rw_cfg strmux_cfg;
++
++	strmux_cfg = REG_RD(strmux, regi_strmux, rw_cfg);
++	if (np->eth_inst == regi_eth0)
++		strmux_cfg.dma1 = regk_strmux_eth0;
++	else
++		strmux_cfg.dma7 = regk_strmux_eth1;
++	REG_WR(strmux, regi_strmux, rw_cfg, strmux_cfg);
++}
++
++static int dma_wait_busy(int inst, int timeout)
++{
++	reg_dma_rw_stream_cmd dma_sc;
++
++	do {
++		dma_sc = REG_RD(dma, inst, rw_stream_cmd);
++	} while (timeout-- > 0 && dma_sc.busy);
++	return dma_sc.busy;
++}
++
++static int __init crisv32_eth_request_irqdma(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	/* Allocate IRQs and DMAs. */
++	if (np->eth_inst == regi_eth0) {
++		if (request_irq(DMA0_INTR_VECT, crisv32tx_eth_interrupt,
++				0, "Ethernet TX", dev)) {
++			return -EAGAIN;
++		}
++
++		if (request_irq(DMA1_INTR_VECT, crisv32rx_eth_interrupt,
++				0, "Ethernet RX", dev))
++			goto err0_1;
++
++		if (crisv32_request_dma(0, cardname, DMA_VERBOSE_ON_ERROR,
++					12500000, dma_eth0))
++			goto err0_2;
++
++		if (crisv32_request_dma(1, cardname, DMA_VERBOSE_ON_ERROR,
++					12500000, dma_eth0))
++			goto err0_3;
++
++		if (request_irq(ETH0_INTR_VECT, crisv32nw_eth_interrupt, 0,
++					cardname, dev)) {
++			crisv32_free_dma(1);
++err0_3:
++			crisv32_free_dma(0);
++err0_2:
++			free_irq(DMA1_INTR_VECT, dev);
++err0_1:
++			free_irq(DMA0_INTR_VECT, dev);
++			return -EAGAIN;
++		}
++	} else {
++		if (request_irq(DMA6_INTR_VECT, crisv32tx_eth_interrupt,
++				0, cardname, dev))
++			return -EAGAIN;
++
++		if (request_irq(DMA7_INTR_VECT, crisv32rx_eth_interrupt,
++				0, cardname, dev))
++			goto err1_1;
++
++		if (crisv32_request_dma(6, cardname, DMA_VERBOSE_ON_ERROR,
++					0, dma_eth1))
++			goto err1_2;
++
++		if (crisv32_request_dma(7, cardname, DMA_VERBOSE_ON_ERROR,
++					0, dma_eth1))
++			goto err1_3;
++
++		if (request_irq(ETH1_INTR_VECT, crisv32nw_eth_interrupt, 0,
++					cardname, dev)) {
++			crisv32_free_dma(7);
++err1_3:
++			crisv32_free_dma(6);
++err1_2:
++			free_irq(DMA7_INTR_VECT, dev);
++err1_1:
++			free_irq(DMA6_INTR_VECT, dev);
++			return -EAGAIN;
++		}
++	}
++	return 0;
++}
++
++static int __init crisv32_eth_init_phy(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	struct timer_list timer_init = TIMER_INITIALIZER(NULL, 0, 0);
++
++	if (RESET_PHY) {
++#ifdef CONFIG_ETRAXFS
++		reg_config_rw_pad_ctrl pad_ctrl;
++		pad_ctrl = REG_RD(config, regi_config, rw_pad_ctrl);
++		pad_ctrl.phyrst_n = 0;
++		REG_WR(config, regi_config, rw_pad_ctrl, pad_ctrl);
++
++		udelay(500); /* RESET_LEN */
++
++		pad_ctrl.phyrst_n = 1;
++		REG_WR(config, regi_config, rw_pad_ctrl, pad_ctrl);
++#else
++		reg_eth_rw_gen_ctrl gen_ctrl = REG_RD(eth, np->eth_inst, rw_gen_ctrl);
++		gen_ctrl.phyrst_n = 0;
++		REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl);
++
++		udelay(500); /* RESET_LEN */
++
++		gen_ctrl.phyrst_n = 1;
++		REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl);
++#endif
++
++		udelay(200); /* RESET_WAIT */
++	}
++
++	switch (PHY_MODE) {
++	case FALLBACK_PHY:
++		/* Fall back on using fixed iff there is no PHY on */
++		/* the MDIO bus */
++		np->fixed_phy = crisv32_eth_probe_transceiver(dev) != 0;
++		if (np->fixed_phy)
++			printk(KERN_WARNING
++				"eth: No transciever found, falling back "
++				"to fixed phy mode\n");
++		break;
++
++	case NO_PHY:
++		/* Don't even bother looking for a PHY, always rely */
++		/* on fixed PHY */
++		np->fixed_phy = 1;
++		break;
++
++	default: /* HAVE_PHY */
++		/* Look for a PHY and abort if there is none, */
++		/* otherwise just carry on */
++		if (crisv32_eth_probe_transceiver(dev)) {
++			printk(KERN_WARNING
++				"eth: No transceiver found, "
++				"removing interface\n");
++			return -ENODEV;
++		}
++		np->fixed_phy = 0;
++	}
++
++	if (np->fixed_phy) {
++		reg_eth_rw_rec_ctrl rec_ctrl;
++
++		/* speed */
++		np->current_speed = 100;
++		np->current_speed_selection = 100;	/* Auto. */
++
++		/* duplex */
++		np->full_duplex = 1;
++		np->current_duplex = full;
++
++		rec_ctrl = REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++		rec_ctrl.duplex = regk_eth_full;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	} else {
++		np->mii_if.supports_gmii = mii_check_gmii_support(&np->mii_if);
++
++		/* speed */
++		np->current_speed = 10;
++		np->current_speed_selection = 0;	/* Auto. */
++		np->speed_timer = timer_init;
++		np->speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL;
++		np->speed_timer.data = (unsigned long) dev;
++		np->speed_timer.function = crisv32_eth_check_speed;
++
++		/* duplex */
++		np->full_duplex = 0;
++		np->current_duplex = autoneg;
++		np->duplex_timer = timer_init;
++		np->duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL;
++		np->duplex_timer.data = (unsigned long) dev;
++		np->duplex_timer.function = crisv32_eth_check_duplex;
++	}
++
++	return 0;
++}
++
++static void __init crisv32_eth_setup_controller(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	reg_eth_rw_gen_ctrl gen_ctrl;
++
++	reg_eth_rw_tr_ctrl tr_ctrl = {
++		/* SW retransmits to avoid transmitter bugs.  */
++		.retry = regk_eth_no,
++		.pad = regk_eth_yes,
++		.crc = regk_eth_yes
++	};
++
++	reg_eth_rw_rec_ctrl rec_ctrl = {
++		.ma0 = regk_eth_no,	/* enable at open() */
++		.broadcast = regk_eth_no,
++		.max_size = regk_eth_size1522
++	};
++
++	reg_eth_rw_ga_lo ga_lo = { 0 };
++	reg_eth_rw_ga_hi ga_hi = { 0 };
++
++	/*
++	 * Initialize group address registers to make sure that no
++	 * unwanted addresses are matched.
++	 */
++	REG_WR(eth, np->eth_inst, rw_ga_lo, ga_lo);
++	REG_WR(eth, np->eth_inst, rw_ga_hi, ga_hi);
++
++	/* Configure receiver and transmitter */
++	REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	REG_WR(eth, np->eth_inst, rw_tr_ctrl, tr_ctrl);
++
++	/*
++	 * Read from rw_gen_ctrl so that we don't override any previous
++	 * configuration.
++	 */
++	gen_ctrl = REG_RD(eth, np->eth_inst, rw_gen_ctrl);
++	gen_ctrl.phy = regk_eth_mii_clk;
++#ifdef CONFIG_ETRAXFS
++	/* On ETRAX FS, this bit has reversed meaning */
++	gen_ctrl.flow_ctrl = regk_eth_no;
++#else
++	gen_ctrl.flow_ctrl = regk_eth_yes;
++#endif
++
++	/* Enable ethernet controller with mii clk. */
++	REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl);
++	gen_ctrl.en = regk_eth_yes;
++	REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl);
++}
++
++static void crisv32_eth_reset_rx_ring(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	int i;
++
++	/* cleanup the rx-ring */
++	for (i = 0; i < NBR_RX_DESC; i++) {
++		struct sk_buff *skb;
++		skb = np->dma_rx_descr_list[i].skb;
++		if (!skb
++		    || (np->dma_rx_descr_list[i].descr.buf !=
++			(void *)virt_to_phys(skb->data))) {
++			if (skb)
++				dev_kfree_skb(skb);
++			skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE);
++			np->dma_rx_descr_list[i].skb = skb;
++			np->dma_rx_descr_list[i].descr.buf =
++				(char*)virt_to_phys(skb->data);
++		}
++		if (np->dma_rx_descr_list[i].descr.in_eop)
++			np->rx_restarts_dropped++;
++		np->dma_rx_descr_list[i].descr.after =
++			(char*)virt_to_phys(skb->data
++					    + MAX_MEDIA_DATA_SIZE);
++		np->dma_rx_descr_list[i].descr.eol = 0;
++		np->dma_rx_descr_list[i].descr.in_eop = 0;
++		/* Workaround cache bug */
++		flush_dma_descr(&np->dma_rx_descr_list[i].descr, 1);
++	}
++
++	/* reset rx-ring */
++	np->active_rx_desc = &np->dma_rx_descr_list[0];
++	np->prev_rx_desc = &np->dma_rx_descr_list[NBR_RX_DESC - 1];
++	np->last_rx_desc = np->prev_rx_desc;
++	np->dma_rx_descr_list[NBR_RX_DESC - 1].descr.eol = 1;
++	flush_dma_descr(&np->dma_rx_descr_list[NBR_RX_DESC - 1].descr, 0);
++	/* ready to accept new packets.  */
++	np->new_rx_package = 1;
++
++	/* Fill context descriptors. */
++	np->ctxt_in.next = 0;
++	np->ctxt_in.saved_data =
++		(void *)virt_to_phys(&np->active_rx_desc->descr);
++	np->ctxt_in.saved_data_buf = np->active_rx_desc->descr.buf;
++}
++
++static inline int crisv32_eth_tx_ring_full(struct crisv32_ethernet_local *np)
++{
++	crisv32_eth_descr *active = np->active_tx_desc;
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	active = phys_to_virt((unsigned long)active->descr.next);
++#endif
++	if (active == np->catch_tx_desc)
++		return 1;
++	return 0;
++}
++
++static void crisv32_eth_reset_tx_ring(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	/* free un-handled tx packets */
++	while (np->txpackets || np->catch_tx_desc != np->active_tx_desc) {
++		np->txpackets--;
++		if (np->catch_tx_desc->skb)
++			dev_kfree_skb(np->catch_tx_desc->skb);
++
++		np->catch_tx_desc->skb = 0;
++		np->catch_tx_desc =
++			phys_to_virt((int)np->catch_tx_desc->descr.next);
++	}
++
++	WARN_ON(np->txpackets != 0);
++	np->txpackets = 0;
++
++	/* reset tx-ring */
++	np->dma_tx_descr_list[0].descr.buf =
++		np->dma_tx_descr_list[0].descr.after = 0;
++	np->dma_tx_descr_list[0].descr.eol = 1;
++
++	np->active_tx_desc = &np->dma_tx_descr_list[0];
++	np->prev_tx_desc = &np->dma_tx_descr_list[NBR_TX_DESC - 1];
++	np->catch_tx_desc = &np->dma_tx_descr_list[0];
++
++	np->ctxt_out.next = 0;
++	np->ctxt_out.saved_data =
++		(void *)virt_to_phys(&np->dma_tx_descr_list[0].descr);
++
++}
++
++static void crisv32_eth_reset_rings(struct net_device *dev)
++{
++	crisv32_eth_reset_tx_ring(dev);
++	crisv32_eth_reset_rx_ring(dev);
++}
++
++/*
++ * Really advance the receive ring. RX interrupts must be off.
++ */
++static void __crisv32_eth_rx_ring_advance(struct crisv32_ethernet_local *np)
++{
++	if (np->newbuf)
++		np->active_rx_desc->descr.buf = (void *) np->newbuf;
++	np->active_rx_desc->descr.after =
++		np->active_rx_desc->descr.buf + MAX_MEDIA_DATA_SIZE;
++	np->active_rx_desc->descr.eol = 1;
++	np->active_rx_desc->descr.in_eop = 0;
++	np->active_rx_desc = phys_to_virt((int)np->active_rx_desc->descr.next);
++	barrier();
++	np->prev_rx_desc->descr.eol = 0;
++
++	/* Workaround cache bug.  */
++	flush_dma_descr(&np->prev_rx_desc->descr, 0);
++	np->prev_rx_desc = phys_to_virt((int)np->prev_rx_desc->descr.next);
++	flush_dma_descr(&np->prev_rx_desc->descr, 1);
++}
++
++/*
++ * Advance the receive ring. RX interrupts must be off.
++ */
++static inline void
++crisv32_eth_rx_ring_advance(struct crisv32_ethernet_local *np)
++{
++	/*
++	 * When the input DMA reaches eol precaution must be taken, otherwise
++	 * the DMA could stop. The problem occurs if the eol flag is re-placed
++	 * on the descriptor that the DMA stands on before the DMA proceed to
++	 * the next descriptor. This case could, for example, happen if there
++	 * is a traffic burst and then the network goes silent. To prevent this
++	 * we make sure that we do not set the eol flag on the descriptor that
++	 * the DMA stands on.
++	 */
++	unsigned long dma_pos;
++
++	/* Get the current input dma position. */
++	dma_pos = REG_RD_INT(dma, np->dma_in_inst, rw_saved_data);
++
++	if (virt_to_phys(&np->active_rx_desc->descr) != dma_pos) {
++		crisv32_eth_descr *cur, *nxt;
++
++		/* Now really advance the ring one step.  */
++		__crisv32_eth_rx_ring_advance(np);
++
++		cur = np->active_rx_desc;
++		nxt = (void *)phys_to_virt((unsigned long)cur->descr.next);
++		flush_dma_descr(&cur->descr, 0);
++		flush_dma_descr(&nxt->descr, 0);
++		if (!cur->descr.in_eop && nxt->descr.in_eop) {
++			/* TODO: Investigate this more. The DMA seems to have
++			   skipped a descriptor, possibly due to incoherence
++			   between the CPU L1 cache and the DMA updates to the
++			   descriptor.  */
++			np->newbuf = (unsigned long) np->active_rx_desc->descr.buf;
++			__crisv32_eth_rx_ring_advance(np);
++		}
++		/* flush after peek.  */
++		flush_dma_descr(&cur->descr, 0);
++		flush_dma_descr(&nxt->descr, 0);
++	} else {
++		/* delay the advancing of the ring.  */
++		np->new_rx_package = 0;
++	}
++}
++
++static void __init crisv32_eth_init_rings(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	int i;
++
++	/* Initialise receive descriptors for interface. */
++	for (i = 0; i < NBR_RX_DESC; i++) {
++		struct sk_buff *skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE);
++
++		np->dma_rx_descr_list[i].skb = skb;
++		np->dma_rx_descr_list[i].descr.buf =
++			(char*)virt_to_phys(skb->data);
++		np->dma_rx_descr_list[i].descr.after =
++		    (char*)virt_to_phys(skb->data + MAX_MEDIA_DATA_SIZE);
++
++		np->dma_rx_descr_list[i].descr.eol = 0;
++		np->dma_rx_descr_list[i].descr.in_eop = 0;
++		np->dma_rx_descr_list[i].descr.next =
++		    (void *) virt_to_phys(&np->dma_rx_descr_list[i + 1].descr);
++	}
++	/* bend the list into a ring */
++	np->dma_rx_descr_list[NBR_RX_DESC - 1].descr.next =
++		(void *) virt_to_phys(&np->dma_rx_descr_list[0].descr);
++
++	/* Initialize transmit descriptors. */
++	for (i = 0; i < NBR_TX_DESC; i++) {
++		np->dma_tx_descr_list[i].descr.wait = 1;
++		np->dma_tx_descr_list[i].descr.eol = 0;
++		np->dma_tx_descr_list[i].descr.out_eop = 0;
++		np->dma_tx_descr_list[i].descr.next =
++			(void*)virt_to_phys(&np->dma_tx_descr_list[i+1].descr);
++	}
++	/* bend the list into a ring */
++	np->dma_tx_descr_list[NBR_TX_DESC - 1].descr.next =
++		(void *) virt_to_phys(&np->dma_tx_descr_list[0].descr);
++
++	crisv32_eth_reset_rings(dev);
++}
++
++static void __init crisv32_init_leds(int ledgrp, struct net_device *dev)
++{
++	struct timer_list timer_init = TIMER_INITIALIZER(NULL, 0, 0);
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	/* Use already allocated led grp if initialized */
++	if (crisv32_leds[ledgrp] != NULL) {
++		np->leds = crisv32_leds[ledgrp];
++		return;
++	}
++
++	crisv32_leds[ledgrp] =
++		kmalloc(sizeof(struct crisv32_eth_leds), GFP_KERNEL);
++
++	crisv32_leds[ledgrp]->ledgrp = ledgrp;
++	crisv32_leds[ledgrp]->led_active = 0;
++	crisv32_leds[ledgrp]->ifisup[0] = 0;
++	crisv32_leds[ledgrp]->ifisup[1] = 0;
++	/* NOTE: Should this value be set to zero as the jiffies timer
++	   can wrap? */
++	crisv32_leds[ledgrp]->led_next_time = jiffies;
++
++	crisv32_leds[ledgrp]->clear_led_timer = timer_init;
++	crisv32_leds[ledgrp]->clear_led_timer.function =
++		crisv32_clear_network_leds;
++	crisv32_leds[ledgrp]->clear_led_timer.data = (unsigned long) dev;
++
++	spin_lock_init(&crisv32_leds[ledgrp]->led_lock);
++
++	np->leds = crisv32_leds[ledgrp];
++}
++
++static int __init crisv32_ethernet_init(void)
++{
++	struct crisv32_ethernet_local *np;
++	int ret = 0;
++
++#ifdef CONFIG_ETRAXFS
++	printk("ETRAX FS 10/100MBit ethernet v0.01 (c)"
++	       " 2003 Axis Communications AB\n");
++#else
++	printk("ARTPEC-3 10/100 MBit ethernet (c)"
++	       " 2003-2009 Axis Communications AB\n");
++#endif
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	{
++		reg_clkgen_rw_clk_ctrl clk_ctrl = REG_RD(clkgen, regi_clkgen,
++							 rw_clk_ctrl);
++		clk_ctrl.eth = clk_ctrl.dma0_1_eth = regk_clkgen_yes;
++		REG_WR(clkgen, regi_clkgen, rw_clk_ctrl, clk_ctrl);
++	}
++#endif
++{
++	int iface0 = 0;
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	if (crisv32_pinmux_alloc_fixed(pinmux_eth))
++		panic("Eth pinmux\n");
++#endif
++
++	if (!(crisv32_dev[iface0] = alloc_etherdev(sizeof *np)))
++		return -ENOMEM;
++
++	ret |= crisv32_ethernet_device_init(crisv32_dev[iface0]);
++
++	crisv32_init_leds(CRIS_LED_GRP_NONE,crisv32_dev[iface0]);
++
++	np = (struct crisv32_ethernet_local *) netdev_priv(crisv32_dev[iface0]);
++	np->eth_inst = regi_eth0;
++	np->dma_out_inst = regi_dma0;
++	np->dma_in_inst = regi_dma1;
++
++	np->mii_if.dev = crisv32_dev[iface0];
++	np->mii_if.mdio_read = crisv32_eth_get_mdio_reg;
++	np->mii_if.mdio_write = crisv32_eth_set_mdio_reg;
++	np->mii_if.phy_id_mask = 0x1f;
++	np->mii_if.reg_num_mask = 0x1f;
++
++	np->use_leds = 1;
++	np->autoneg_normal = 1;
++
++
++	register_netdev(crisv32_dev[iface0]);
++
++	/* Set up default MAC address */
++	memcpy(crisv32_dev[iface0]->dev_addr, default_mac_iface0.sa_data, 6);
++	crisv32_eth_set_mac_address(crisv32_dev[iface0], &default_mac_iface0);
++	if (crisv32_eth_request_irqdma(crisv32_dev[iface0]))
++		printk("%s: eth0 unable to allocate IRQ and DMA resources\n",
++		       __func__);
++	np->txpackets = 0;
++	crisv32_eth_init_rings(crisv32_dev[iface0]);
++	crisv32_eth_setup_controller(crisv32_dev[iface0]);
++	ret |= crisv32_eth_init_phy(crisv32_dev[iface0]);
++	if (ret) {
++		unregister_netdev(crisv32_dev[iface0]);
++		return ret;
++	}
++}
++
++#ifdef CONFIG_ETRAX_ETHERNET_IFACE1
++{
++	int iface1 = 0;
++	/* Default MAC address for interface 1.
++	 * The real one will be set later. */
++	static struct sockaddr default_mac_iface1 =
++		{0, {0x00, 0x40, 0x8C, 0xCD, 0x00, 0x01}};
++
++	if (crisv32_pinmux_alloc_fixed(pinmux_eth1))
++		panic("Eth pinmux\n");
++
++	/* Increase index to device array if interface 0 is enabled as well.*/
++#ifdef CONFIG_ETRAX_ETHERNET_IFACE0
++	iface1++;
++#endif
++	if (!(crisv32_dev[iface1] = alloc_etherdev(sizeof *np)))
++		return -ENOMEM;
++
++	ret |= crisv32_ethernet_device_init(crisv32_dev[iface1]);
++
++	crisv32_init_leds(CRIS_LED_GRP_NONE,crisv32_dev[iface1]);
++
++	np = (struct crisv32_ethernet_local *) netdev_priv(crisv32_dev[iface1]);
++	np->eth_inst = regi_eth1;
++	np->dma_out_inst = regi_dma6;
++	np->dma_in_inst = regi_dma7;
++
++	np->mii_if.dev = crisv32_dev[iface1];
++	np->mii_if.mdio_read = crisv32_eth_get_mdio_reg;
++	np->mii_if.mdio_write = crisv32_eth_set_mdio_reg;
++	np->mii_if.phy_id_mask = 0x1f;
++	np->mii_if.reg_num_mask = 0x1f;
++
++
++	register_netdev(crisv32_dev[iface1]);
++
++	/* Set up default MAC address */
++	memcpy(crisv32_dev[iface1]->dev_addr, default_mac_iface1.sa_data, 6);
++	crisv32_eth_set_mac_address(crisv32_dev[iface1], &default_mac_iface1);
++
++	if (crisv32_eth_request_irqdma(crisv32_dev[iface1]))
++		printk("%s: eth1 unable to allocate IRQ and DMA resources\n",
++		       __func__);
++	np->txpackets = 0;
++	crisv32_eth_init_rings(crisv32_dev[iface1]);
++	crisv32_eth_setup_controller(crisv32_dev[iface1]);
++	ret |= crisv32_eth_init_phy(crisv32_dev[iface1]);
++	if (ret) {
++		unregister_netdev(crisv32_dev[iface1]);
++		return ret;
++	}
++}
++#endif /* CONFIG_ETRAX_ETHERNET_IFACE1 */
++
++#ifdef CONFIG_CPU_FREQ
++	cpufreq_register_notifier(&crisv32_ethernet_freq_notifier_block,
++				  CPUFREQ_TRANSITION_NOTIFIER);
++#endif
++
++	return ret;
++}
++
++static struct net_device_ops crisv32_netdev_ops = {
++	.ndo_open = crisv32_eth_open,
++	.ndo_stop = crisv32_eth_close,
++	.ndo_start_xmit = crisv32_eth_send_packet,
++	.ndo_set_rx_mode = crisv32_eth_set_rx_mode,
++	.ndo_validate_addr = eth_validate_addr,
++	.ndo_set_mac_address = crisv32_eth_set_mac_address,
++	.ndo_do_ioctl =crisv32_eth_ioctl,
++	.ndo_get_stats = crisv32_get_stats,
++	.ndo_tx_timeout = crisv32_eth_do_tx_recovery,
++	.ndo_set_config = crisv32_eth_set_config,
++};
++
++static int __init crisv32_ethernet_device_init(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np;
++	struct timer_list timer_init = TIMER_INITIALIZER(NULL, 0, 0);
++
++	dev->base_addr = 0;	/* Just to have something to show. */
++
++	/* we do our own locking */
++	dev->features |= NETIF_F_LLTX;
++
++	/* We use several IRQs and DMAs so just report 0 here. */
++	dev->irq = 0;
++	dev->dma = 0;
++
++	/*
++	 * Fill in our handlers so the network layer can talk to us in the
++	 * future.
++	 */
++	dev->netdev_ops = &crisv32_netdev_ops;
++	dev->ethtool_ops = &crisv32_ethtool_ops;
++	dev->watchdog_timeo = HZ * 10;
++#ifdef CONFIG_NET_POLL_CONTROLLER
++	dev->poll_controller = crisv32_netpoll;
++#endif
++	np = netdev_priv(dev);
++	np->dev = dev;
++
++	/*
++	 * 8 skbs keeps the system very reponsive even under high load.
++	 * At 64 the system locks, pretty much the same way as without NAPI.
++	 *
++	 * TODO: meassure with 2 interfaces
++	 */
++	netif_napi_add(dev, &np->napi, crisv32_eth_poll, 8);
++
++	spin_lock_init(&np->lock);
++	spin_lock_init(&np->transceiver_lock);
++
++	np->receive_timer = timer_init;
++	np->receive_timer.data = (unsigned)dev;
++	np->receive_timer.function = receive_timeout;
++
++	INIT_WORK(&np->receive_work, receive_timeout_work);
++
++	np->transmit_timer = timer_init;
++	np->transmit_timer.data = (unsigned)dev;
++	np->transmit_timer.function = transmit_timeout;
++
++	return 0;
++}
++
++static int crisv32_eth_open(struct net_device *dev)
++{
++	struct sockaddr mac_addr;
++	reg_dma_rw_ack_intr ack_intr = { .data = 1, .in_eop = 1 };
++	reg_eth_rw_clr_err clr_err = {.clr = regk_eth_yes};
++	/*
++	 * dont interrupt us at any stat counter thresholds, only at urun
++	 * and exc_col.
++	 */
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	/* For Artpec-3 we use overrun to workaround voodoo TR 87 */
++	int intr_mask_nw = 0x1c00;
++#else
++	int intr_mask_nw = 0x1800;
++#endif
++	int eth_ack_intr = 0xffff;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	spin_lock(&np->lock);
++	crisv32_eth_set_gigabit(np, 0);
++
++	crisv32_disable_tx_ints(np);
++	crisv32_disable_rx_ints(np);
++
++	REG_WR(eth, np->eth_inst, rw_clr_err, clr_err);
++	REG_WR_INT(eth, np->eth_inst, rw_ack_intr, eth_ack_intr);
++	REG_WR_INT(eth, np->eth_inst, rw_intr_mask, intr_mask_nw);
++	crisv32_eth_reset_rings(dev);
++
++	/* Give the hardware an idea of what MAC address we want. */
++	memcpy(mac_addr.sa_data, dev->dev_addr, dev->addr_len);
++	crisv32_eth_set_mac_address(dev, &mac_addr);
++
++	/* Enable irq and make sure that the irqs are cleared. */
++	REG_WR(dma, np->dma_out_inst, rw_ack_intr, ack_intr);
++	REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr);
++
++	crisv32_disconnect_eth_rx_dma(np);
++
++	/* Prepare input DMA. */
++	DMA_RESET(np->dma_in_inst);
++	DMA_ENABLE(np->dma_in_inst);
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	DMA_WR_CMD(np->dma_in_inst, regk_dma_set_w_size2);
++#endif
++	DMA_START_CONTEXT(np->dma_in_inst, virt_to_phys(&np->ctxt_in));
++	DMA_CONTINUE(np->dma_in_inst);
++	crisv32_enable_rx_ints(np);
++	crisv32_start_receiver(np);
++
++	/* Prepare output DMA. */
++	DMA_RESET(np->dma_out_inst);
++	DMA_ENABLE(np->dma_out_inst);
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	DMA_WR_CMD(np->dma_out_inst, regk_dma_set_w_size4);
++#endif
++	crisv32_connect_eth_rx_dma(np);
++
++	netif_start_queue(dev);
++	crisv32_enable_tx_ints(np);
++
++	if (!np->fixed_phy) {
++		/* Start duplex/speed timers */
++		if (!timer_pending(&np->speed_timer))
++			add_timer(&np->speed_timer);
++		if (!timer_pending(&np->duplex_timer))
++			add_timer(&np->duplex_timer);
++	}
++
++	spin_unlock(&np->lock);
++	/*
++	 * We are now ready to accept transmit requests from the queueing
++	 * layer of the networking.
++	 */
++	np->link = 1;
++	netif_carrier_on(dev);
++	napi_enable(&np->napi);
++
++	return 0;
++}
++
++static int crisv32_eth_close(struct net_device *dev)
++{
++	reg_dma_rw_ack_intr ack_intr = {0};
++
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	unsigned long flags;
++
++	del_timer(&np->transmit_timer);
++	spin_lock_irqsave(&np->lock, flags);
++
++	/* stop the receiver before the DMA channels to avoid overruns. */
++	crisv32_disable_rx_ints(np);
++	napi_disable(&np->napi);
++	crisv32_stop_receiver(np);
++
++	netif_stop_queue(dev);
++
++	/* Reset the TX DMA in case it has hung on something. */
++	DMA_RESET(np->dma_in_inst);
++
++	/* Stop DMA */
++	DMA_STOP(np->dma_in_inst);
++	DMA_STOP(np->dma_out_inst);
++
++	/* Disable irq and make sure that the irqs are cleared. */
++	crisv32_disable_tx_ints(np);
++	ack_intr.data = 1;
++	REG_WR(dma, np->dma_out_inst, rw_ack_intr, ack_intr);
++
++	ack_intr.in_eop = 1;
++	REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr);
++
++	np->sender_started = 0;
++	spin_unlock_irqrestore(&np->lock, flags);
++
++	/* Update the statistics. */
++	update_rx_stats(np);
++	update_tx_stats(np);
++
++	if (!np->fixed_phy) {
++		/* Stop speed/duplex timers */
++		del_timer(&np->speed_timer);
++		del_timer(&np->duplex_timer);
++	}
++
++	return 0;
++}
++
++static int crisv32_eth_set_mac_address(struct net_device *dev, void *vpntr)
++{
++	int i;
++	static int first = 1;
++
++	unsigned char *addr = ((struct sockaddr*)vpntr)->sa_data;
++
++	reg_eth_rw_ma0_lo ma0_lo =
++	  { addr[0] | (addr[1] << 8) | (addr[2] << 16) | (addr[3] << 24)};
++
++	reg_eth_rw_ma0_hi ma0_hi = { addr[4] | (addr[5] << 8) };
++
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	/* Remember the address. */
++	memcpy(dev->dev_addr, addr, dev->addr_len);
++
++	/*
++	 * Write the address to the hardware.
++	 * Note the way the address is wrapped:
++	 * ma0_l0 = a0_0 | (a0_1 << 8) | (a0_2 << 16) | (a0_3 << 24);
++	 * ma0_hi = a0_4 | (a0_5 << 8);
++	 */
++	REG_WR(eth, np->eth_inst, rw_ma0_lo, ma0_lo);
++	REG_WR(eth, np->eth_inst, rw_ma0_hi, ma0_hi);
++
++	if (first) {
++		printk(KERN_INFO "%s: changed MAC to ", dev->name);
++
++		for (i = 0; i < 5; i++)
++			printk("%02X:", dev->dev_addr[i]);
++		printk("%02X\n", dev->dev_addr[i]);
++
++		first = 0;
++	}
++
++	return 0;
++}
++
++static irqreturn_t crisv32rx_eth_interrupt(int irq, void *dev_id)
++{
++	struct net_device *dev = (struct net_device *) dev_id;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	reg_dma_r_masked_intr masked_in;
++
++	masked_in = REG_RD(dma, np->dma_in_inst, r_masked_intr);
++
++	if (masked_in.in_eop) {
++		reg_dma_rw_ack_intr ack_intr = {0};
++
++		/*
++		 * Ack the rx irq even if we are not prepared to start
++		 * polling. This is needed to handle incomming packets
++		 * during the stop sequence.
++		 */
++		ack_intr.in_eop = 1;
++		REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr);
++
++		mod_timer(&np->receive_timer, jiffies + HZ);
++		np->do_rx_recovery = 0;
++
++		if (napi_schedule_prep(&np->napi)) {
++			crisv32_disable_rx_ints(np);
++			crisv32_disable_tx_ints(np);
++			/* put us onto the poll list */
++			__napi_schedule(&np->napi);
++		}
++	} else {
++		/* Unexpected, ACK it and hope for the best.  */
++		reg_dma_rw_ack_intr ack_intr = {
++			.group = 1,
++			.ctxt = 1,
++			.data = 1,
++			.in_eop = 0,
++			.stream_cmd = 1,
++			.dummy1 = ~0
++		};
++		REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr);
++	}
++
++	return IRQ_HANDLED;
++}
++
++static inline void crisv32_eth_roll_tx_timer(struct crisv32_ethernet_local *np)
++{
++	/* If there are more packets in the ring, roll the tx timer.  */
++	if (np->txpackets) {
++		/* Eth pause frames may halt us for up to 320ms (100mbit).  */
++		unsigned long timeout = jiffies + (HZ / 3) + 1;
++		mod_timer(&np->transmit_timer, timeout);
++	}
++	else
++		del_timer(&np->transmit_timer);
++}
++
++/* Call with np->lock held.  */
++static void _crisv32_tx_ring_advance(struct crisv32_ethernet_local *np,
++				     int cleanup)
++{
++	reg_dma_rw_stat stat;
++	dma_descr_data *dma_pos;
++	struct net_device *dev = np->dev;
++	int eol;
++
++	/* Get the current output dma position. */
++	dma_pos = phys_to_virt(REG_RD_INT(dma, np->dma_out_inst, rw_data));
++	stat = REG_RD(dma, np->dma_out_inst, rw_stat);
++	eol = stat.list_state == regk_dma_data_at_eol;
++	if (cleanup || eol)
++		dma_pos = &np->active_tx_desc->descr;
++
++	/* Take care of transmited dma descriptors and report sent packet. */
++	while (np->txpackets && (&np->catch_tx_desc->descr != dma_pos)) {
++		/* Update sent packet statistics. */
++		np->stats.tx_bytes += np->catch_tx_desc->skb->len;
++		np->stats.tx_packets++;
++
++		dev_kfree_skb_any(np->catch_tx_desc->skb);
++		np->catch_tx_desc->skb = 0;
++		np->txpackets--;
++		np->catch_tx_desc->descr.buf = 0;
++		np->catch_tx_desc =
++			phys_to_virt((int)np->catch_tx_desc->descr.next);
++		np->do_tx_recovery = 0;
++		np->retrans = 0;
++
++		netif_wake_queue(dev);
++	}
++}
++
++static inline void crisv32_tx_ring_advance(struct crisv32_ethernet_local *np)
++{
++	unsigned long flags;
++
++	spin_lock_irqsave(&np->lock, flags);
++	_crisv32_tx_ring_advance(np, 0);
++	crisv32_eth_roll_tx_timer(np);
++	spin_unlock_irqrestore(&np->lock, flags);
++}
++
++static inline int crisv32_tx_complete(struct crisv32_ethernet_local *np)
++{
++	reg_dma_rw_ack_intr ack_intr = { .data = 1 };
++	reg_dma_r_intr ints;
++	int r = 0;
++
++	/* We are interested in the unmasked raw interrupt source here. When
++	   polling with tx interrupts masked off we still want to do
++	   tx completition when the DMA makes progress.  */
++	ints = REG_RD(dma, np->dma_out_inst, r_intr);
++	if (ints.data)
++	{
++		/* ack the interrupt, if it was active */
++		REG_WR(dma, np->dma_out_inst, rw_ack_intr, ack_intr);
++		crisv32_tx_ring_advance(np);
++		r = 1;
++	}
++	return r;
++}
++
++static irqreturn_t crisv32tx_eth_interrupt(int irq, void *dev_id)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev_id);
++
++	crisv32_tx_complete(np);
++	return IRQ_HANDLED;
++}
++
++
++/* Update receive errors. */
++static void
++update_rx_stats(struct crisv32_ethernet_local *np)
++{
++	reg_eth_rs_rec_cnt r;
++
++	r = REG_RD(eth, np->eth_inst, rs_rec_cnt);
++
++	np->stats.rx_over_errors += r.congestion;
++	np->stats.rx_crc_errors += r.crc_err;
++	np->stats.rx_frame_errors += r.align_err;
++	np->stats.rx_length_errors += r.oversize;
++	np->stats.rx_errors += r.crc_err + r.align_err +
++			r.oversize + r.congestion;
++}
++
++/* Update transmit errors. */
++static void update_tx_stats(struct crisv32_ethernet_local *np)
++{
++	reg_eth_rs_tr_cnt r;
++	reg_eth_rs_phy_cnt rp;
++
++	r = REG_RD(eth, np->eth_inst, rs_tr_cnt);
++	rp = REG_RD(eth, np->eth_inst, rs_phy_cnt);
++
++	/* r.deferred is not good for counting collisions because it also
++	   includes frames that have to wait for the interframe gap. That
++	   means we get deferred frames even when in full duplex.
++	   Here we don't actually count the number of collisions that
++	   occured (artpec3 seems to lack such a counter), instead we count
++	   the number of frames that collide once or more.  */
++	np->stats.collisions += r.mult_col + r.single_col;
++	np->stats.tx_window_errors += r.late_col;
++	np->stats.tx_carrier_errors += rp.carrier_loss;
++
++	/* Ordinary collisions are not errors, they are just part of
++	   ethernet's bus arbitration and congestion control mechanisms.
++	   Late collisions are serious errors though.  */
++	np->stats.tx_errors += r.late_col;
++}
++
++/* Get current statistics. */
++static struct net_device_stats *crisv32_get_stats(struct net_device *dev)
++{
++	unsigned long flags;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	spin_lock_irqsave(&np->lock, flags);
++
++	update_rx_stats(np);
++	update_tx_stats(np);
++
++	spin_unlock_irqrestore(&np->lock, flags);
++
++	return &np->stats;
++}
++
++/* Check for network errors. This acknowledge the received interrupt. */
++static irqreturn_t crisv32nw_eth_interrupt(int irq, void *dev_id)
++{
++	struct net_device *dev = (struct net_device *) dev_id;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	reg_eth_r_masked_intr intr_mask;
++	int ack_intr = 0xffff;
++	reg_eth_rw_clr_err clr_err;
++
++	intr_mask = REG_RD(eth, np->eth_inst, r_masked_intr);
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	/* Only apply the workaround if it is not already pending.
++	   enable_eth_ints will re-enable the orun interrupt regardless
++	   of pending_overrun.  */
++	if (intr_mask.orun && !np->pending_overrun) {
++		reg_eth_rw_rec_ctrl rec_ctrl =
++			REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++		np->saved_rec_ctrl = rec_ctrl;
++		np->overrun_set = 1;
++		DMA_STOP(np->dma_in_inst);
++		rec_ctrl.ma0 = regk_eth_no;
++		rec_ctrl.broadcast = regk_eth_no;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++		np->saved_ga_lo = REG_RD_INT(eth, np->eth_inst, rw_ga_lo);
++		np->saved_ga_hi = REG_RD_INT(eth, np->eth_inst, rw_ga_hi);
++		REG_WR_INT(eth, np->eth_inst, rw_ga_lo, 0);
++		REG_WR_INT(eth, np->eth_inst, rw_ga_hi, 0);
++		REG_WR_INT(eth, np->eth_inst, rw_intr_mask,
++			REG_RD_INT(eth, np->eth_inst, rw_intr_mask) & 0xfbff);
++		REG_WR_INT(eth, np->eth_inst, rw_ack_intr, 0x400);
++		intr_mask.orun = 0;
++		np->pending_overrun = 1;
++		if (!np->napi_processing)
++			crisv32_eth_restart_rx_dma(np->dev, np);
++
++		return IRQ_HANDLED;
++	}
++#endif
++
++	/*
++	 * Check for underrun and/or excessive collisions. Note that the
++	 * rw_clr_err register clears both underrun and excessive collision
++	 * errors, so there's no need to check them separately.
++	 */
++	if (np->sender_started
++	    && (intr_mask.urun || intr_mask.exc_col)) {
++		unsigned long flags;
++
++		/* Underrun are considered to be tx-errors.  */
++		np->stats.tx_errors += intr_mask.urun;
++		np->stats.tx_fifo_errors += intr_mask.urun;
++
++		/*
++		 * Protect against the tx-interrupt messing with
++		 * the tx-ring.
++		 */
++		spin_lock_irqsave(&np->lock, flags);
++
++		/* DMA should have stopped now, eat from the ring before
++		   removing anything due to tx errors.  */
++		_crisv32_tx_ring_advance(np, 0);
++
++		/*
++		 * Drop packets after 15 retries.
++		 * TODO: Add backoff.
++		 */
++		if (np->retrans > 15 && np->txpackets) {
++			dev_kfree_skb_irq(np->catch_tx_desc->skb);
++			np->catch_tx_desc->skb = 0;
++			np->catch_tx_desc->descr.buf = 0;
++			np->catch_tx_desc =
++				phys_to_virt((int)
++					     np->catch_tx_desc->descr.next);
++			flush_dma_descr(&np->catch_tx_desc->descr, 0);
++
++			np->txpackets--;
++			np->retrans = 0;
++			netif_wake_queue(dev);
++			np->stats.tx_dropped++;
++		}
++		np->ctxt_out.next = 0;
++		if (np->txpackets) {
++			np->retrans++;
++			np->ctxt_out.saved_data = (void *)
++				virt_to_phys(&np->catch_tx_desc->descr);
++			np->ctxt_out.saved_data_buf =
++				np->catch_tx_desc->descr.buf;
++			WARN_ON(!np->ctxt_out.saved_data_buf);
++			flush_dma_descr(&np->catch_tx_desc->descr, 0);
++			cris_flush_cache_range(&np->ctxt_out,
++					       sizeof np->ctxt_out);
++
++			/* restart the DMA */
++			DMA_START_CONTEXT(np->dma_out_inst,
++					  (int) virt_to_phys(&np->ctxt_out));
++			np->sender_started = 1;
++		}
++		else {
++			/* Load dummy context but do not load the data
++			   descriptor nor start the burst. This brings the
++			   buggy eth transmitter back in sync with the DMA
++			   avoiding malformed frames.  */
++			REG_WR(dma, np->dma_out_inst, rw_group_down,
++			       (int) virt_to_phys(&np->ctxt_out));
++			DMA_WR_CMD(np->dma_out_inst, regk_dma_load_c);
++			np->sender_started = 0;
++		}
++		crisv32_eth_roll_tx_timer(np);
++		spin_unlock_irqrestore(&np->lock, flags);
++	}
++
++	ack_intr = *(u32 *)&intr_mask;
++	REG_WR_INT(eth, np->eth_inst, rw_ack_intr, ack_intr);
++	clr_err.clr = 1;
++	REG_WR(eth, np->eth_inst, rw_clr_err, clr_err);
++
++	update_rx_stats(np);
++	update_tx_stats(np);
++
++	return IRQ_HANDLED;
++}
++
++/* We have a good packet(s), get it/them out of the buffers. */
++static int crisv32_eth_receive_packet(struct net_device *dev)
++{
++	int length;
++	struct sk_buff *skb;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	struct sk_buff *tmp;
++	unsigned long flags;
++
++	DEBUG(printk("crisv32_receive_packet\n"));
++
++	/* Roll the rx bug timer.  */
++	mod_timer(&np->receive_timer, jiffies + HZ);
++
++	/* Activate LED */
++	spin_lock_irqsave(&np->leds->led_lock, flags);
++	if (!np->leds->led_active && time_after(jiffies,
++						np->leds->led_next_time)) {
++		/* light the network leds depending on the current speed. */
++		crisv32_set_network_leds(CRIS_LED_ACTIVITY, dev);
++
++		/* Set the earliest time we may clear the LED */
++		np->leds->led_next_time = jiffies + NET_FLASH_TIME;
++		np->leds->led_active = 1;
++		np->leds->clear_led_timer.data = (unsigned long) dev;
++		mod_timer(&np->leds->clear_led_timer, jiffies + HZ/10);
++	}
++	spin_unlock_irqrestore(&np->leds->led_lock, flags);
++
++	/* Discard CRC (4 bytes). */
++	length = (np->active_rx_desc->descr.after) -
++		(np->active_rx_desc->descr.buf) - 4;
++
++	tmp = dev_alloc_skb(MAX_MEDIA_DATA_SIZE);
++	if (!tmp) {
++		np->stats.rx_errors++;
++		printk(KERN_NOTICE "%s: memory squeeze,"
++		       " dropping packet.",
++		       dev->name);
++		return 0;
++	}
++	skb = np->active_rx_desc->skb;
++	np->active_rx_desc->skb = tmp;
++	skb_put(skb, length);
++
++	np->newbuf = virt_to_phys(np->active_rx_desc->skb->data);
++
++	skb->dev = dev;
++	skb->protocol = eth_type_trans(skb, dev);
++	skb->ip_summed = CHECKSUM_NONE;
++
++	np->stats.multicast += skb->pkt_type == PACKET_MULTICAST;
++	/* Send the packet to the upper layer. */
++	netif_receive_skb(skb);
++	np->last_rx_desc =
++		phys_to_virt((int)
++			     np->last_rx_desc->descr.next);
++
++	/* Forward rotate the receive ring.  */
++	crisv32_eth_rx_ring_advance(np);
++	return length;
++}
++
++/* Must be called with the np-lock held.  */
++static void
++__crisv32_eth_restart_rx_dma(struct net_device* dev,
++			     struct crisv32_ethernet_local *np)
++{
++	reg_dma_rw_ack_intr ack_intr = {0};
++	reg_dma_rw_stream_cmd dma_sc = {0};
++	reg_dma_rw_stat stat;
++	int resets = 0;
++	reg_eth_rw_intr_mask eth_intr_mask;
++
++	np->rx_dma_restarts++;
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	if (np->pending_overrun) {
++		np->pending_overrun = 0;
++		REG_WR_INT(eth, np->eth_inst, rw_ga_lo, np->saved_ga_lo);
++		REG_WR_INT(eth, np->eth_inst, rw_ga_hi, np->saved_ga_hi);
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, np->saved_rec_ctrl);
++		REG_WR_INT(eth, np->eth_inst, rw_intr_mask,
++			   REG_RD_INT(eth, regi_eth, rw_intr_mask) | 0x400);
++		DMA_CONTINUE(np->dma_in_inst);
++	}
++#endif
++	/* Bring down the receiver.  */
++	crisv32_disable_rx_ints(np);
++	crisv32_disconnect_eth_rx_dma(np);
++
++	/* Stop DMA and ack possible ints.  */
++	DMA_STOP(np->dma_in_inst);
++	ack_intr.in_eop = 1;
++	REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr);
++
++	crisv32_stop_receiver(np);
++
++	/* Disable overrun interrupts while receive is shut off. */
++	eth_intr_mask = REG_RD(eth, np->eth_inst, rw_intr_mask);
++	eth_intr_mask.orun = regk_eth_no;
++	REG_WR(eth, np->eth_inst, rw_intr_mask, eth_intr_mask);
++	/* ACK overrun.  */
++	REG_WR_INT(eth, np->eth_inst, rw_ack_intr, 0x400);
++
++	crisv32_eth_reset_rx_ring(dev);
++  reset:
++	/* TODO: if nr resets grows to high we should reboot.  */
++	if (resets++ > 0)
++		printk("reset DMA %d.\n", resets);
++
++	DMA_RESET(np->dma_in_inst);
++	/* Wait for the channel to reset.  */
++	do {
++		stat = REG_RD(dma, np->dma_in_inst, rw_stat);
++	} while (stat.mode != regk_dma_rst);
++
++	/* Now bring the rx path back up.  */
++	DMA_ENABLE(np->dma_in_inst);
++	if (dma_wait_busy(np->dma_in_inst, 100))
++		goto reset;
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++//	DMA_WR_CMD(np->dma_in_inst, regk_dma_set_w_size2);
++	dma_sc.cmd = (regk_dma_set_w_size2);
++	REG_WR(dma, np->dma_in_inst, rw_stream_cmd, dma_sc);
++	if (dma_wait_busy(np->dma_in_inst, 100))
++		goto reset;
++#endif
++
++//	DMA_START_CONTEXT(np->dma_in_inst, virt_to_phys(&np->ctxt_in));
++	REG_WR_INT(dma, np->dma_in_inst, rw_group_down, (int)&np->ctxt_in);
++
++//	DMA_WR_CMD(np->dma_in_inst, regk_dma_load_c);
++	dma_sc.cmd = (regk_dma_load_c);
++	REG_WR(dma, np->dma_in_inst, rw_stream_cmd, dma_sc);
++	if (dma_wait_busy(np->dma_in_inst, 100))
++		goto reset;
++
++//	DMA_WR_CMD(np->dma_in_inst, regk_dma_load_d | regk_dma_burst);
++	dma_sc.cmd = (regk_dma_load_d | regk_dma_burst);
++	REG_WR(dma, np->dma_in_inst, rw_stream_cmd, dma_sc);
++
++	if (dma_wait_busy(np->dma_in_inst, 100))
++		goto reset;
++
++	/* Now things get critical again. Don't give us any interrupts until
++	   the following sequence is complete.  */
++	DMA_CONTINUE(np->dma_in_inst);
++	np->overrun_set = 0;
++	crisv32_enable_rx_ints(np);
++	crisv32_start_receiver(np);
++
++	/* Reenable overrun interrupts when receive is started again. */
++	eth_intr_mask = REG_RD(eth, np->eth_inst, rw_intr_mask);
++	eth_intr_mask.orun = regk_eth_yes;
++	REG_WR(eth, np->eth_inst, rw_intr_mask, eth_intr_mask);
++
++	crisv32_connect_eth_rx_dma(np);
++}
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++static void
++crisv32_eth_restart_rx_dma(struct net_device* dev,
++			   struct crisv32_ethernet_local *np)
++{
++	unsigned long flags;
++
++	spin_lock_irqsave(&np->lock, flags);
++	__crisv32_eth_restart_rx_dma(dev, np);
++	spin_unlock_irqrestore(&np->lock, flags);
++}
++#endif
++
++/*
++ * Is there work to do in the rx-path?
++ */
++static inline int crisv32_has_rx_work(struct crisv32_ethernet_local *np,
++				      dma_descr_data *active)
++{
++	int mw;
++	mw = (active->in_eop && np->new_rx_package);
++	return mw;
++}
++
++static void crisv32_eth_do_rx_recovery(struct net_device* dev,
++				       struct crisv32_ethernet_local *np)
++{
++	unsigned long flags;
++	static int r = 0;
++
++	r++;
++
++	/* Bring down the receiver.  */
++	spin_lock_irqsave(&np->lock, flags);
++	if (!np->do_rx_recovery)
++		goto done;
++
++	napi_disable(&np->napi);
++
++	np->rx_dma_timeouts++;
++
++	__crisv32_eth_restart_rx_dma(dev, np);
++
++	np->do_rx_recovery = 0;
++
++	napi_enable(&np->napi);
++  done:
++	spin_unlock_irqrestore(&np->lock, flags);
++
++	WARN_ON(r != 1);
++	r--;
++}
++
++static void receive_timeout_work(struct work_struct* work)
++{
++	struct dma_descr_data* descr;
++	struct dma_descr_data* descr2;
++	struct net_device* dev = crisv32_dev[0];
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	reg_eth_r_intr intr_mask;
++
++	descr = &np->active_rx_desc->descr;
++	descr2 = phys_to_virt(REG_RD_INT(dma, np->dma_in_inst, rw_data));
++
++	intr_mask = REG_RD(eth, np->eth_inst, r_intr);
++
++	if (!np->overrun_set
++	    && !intr_mask.orun
++	    && !descr->in_eop
++	    && !descr2->in_eop)
++		return;
++
++	crisv32_eth_do_rx_recovery(dev, np);
++}
++
++static void receive_timeout(unsigned long arg)
++{
++	struct net_device* dev = (struct net_device*)arg;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	np->do_rx_recovery++;
++	schedule_work(&np->receive_work);
++	mod_timer(&np->receive_timer, jiffies + 1*HZ);
++}
++
++static void transmit_timeout(unsigned long arg)
++{
++	struct net_device* dev = (struct net_device*)arg;
++	crisv32_eth_do_tx_recovery(dev);
++}
++
++/*
++ * NAPI poll
++ *
++ * We are allowed to pull up to budget number of frames from the rx ring.
++ * If we are done, remove us from the poll list and re-enable rx interrupts.
++ * Always return number of pulled frames from the rx ring.
++ */
++static int crisv32_eth_poll(struct napi_struct *napi, int budget)
++{
++	struct crisv32_ethernet_local *np;
++	int work_done = 0;
++	int morework;
++	int rx_bytes = 0;
++	reg_dma_rw_ack_intr ack_intr = {0};
++
++	np = container_of(napi, struct crisv32_ethernet_local, napi);
++	crisv32_disable_eth_ints(np);
++	np->napi_processing = 1;
++	ack_intr.in_eop = 1;
++
++	if (np->new_rx_package == 0) {
++		/*
++		 * In the previous round we pulled a packet from the ring but
++		 * we didn't advance the ring due to hw DMA bug. Try to do it
++		 * now.
++		 */
++		np->new_rx_package = 1;
++		crisv32_eth_rx_ring_advance(np);
++	}
++
++	morework = crisv32_has_rx_work(np, &np->active_rx_desc->descr);
++
++	/* See if tx needs attention.  */
++	crisv32_tx_complete(np);
++
++	while (morework)
++	{
++		rx_bytes += crisv32_eth_receive_packet(np->dev);
++		work_done++;
++
++		/* Ack irq and restart rx dma */
++		REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr);
++		DMA_CONTINUE_DATA(np->dma_in_inst);
++
++		if (unlikely(work_done >= budget))
++			break;
++
++		/* See if tx needs attention.  */
++		crisv32_tx_complete(np);
++
++		morework = crisv32_has_rx_work(np, &np->active_rx_desc->descr);
++	}
++	crisv32_enable_eth_ints(np);
++
++	if (!morework) {
++		np->napi_processing = 0;
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++		if (np->pending_overrun) {
++			crisv32_eth_restart_rx_dma(np->dev, np);
++		}
++#endif
++		if (irqs_disabled())
++			printk("WARNING: %s irqs disabled!\n", __func__);
++
++		if (work_done < budget) {
++			/* first mark as done, then enable irq's */
++			napi_complete(napi);
++			crisv32_enable_rx_ints(np);
++			crisv32_enable_tx_ints(np);
++		}
++	}
++	np->napi_processing = 0;
++
++	np->stats.rx_bytes += rx_bytes;
++	np->stats.rx_packets += work_done;
++	update_rx_stats(np);
++	return work_done;
++}
++
++/*
++ * This function (i.e. hard_start_xmit) is protected from concurent calls by a
++ * spinlock (xmit_lock) in the net_device structure.
++ */
++static int
++crisv32_eth_send_packet(struct sk_buff *skb, struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	unsigned char *buf = skb->data;
++	unsigned long flags;
++
++	/*
++	 * Need to disable irq to avoid updating pointer in interrupt while
++	 * sending packets.
++	 */
++	spin_lock_irqsave(&np->lock, flags);
++
++	np->active_tx_desc->skb = skb;
++	crisv32_eth_hw_send_packet(buf, skb->len, np);
++
++	dev->trans_start = jiffies;
++
++	/* Stop queue if full. */
++	if (crisv32_eth_tx_ring_full(np))
++		netif_stop_queue(dev);
++
++	np->txpackets++;
++	crisv32_eth_roll_tx_timer(np);
++	spin_unlock_irqrestore(&np->lock, flags);
++
++	spin_lock_irqsave(&np->leds->led_lock, flags);
++	if (!np->leds->led_active && time_after(jiffies,
++						np->leds->led_next_time)) {
++		/* light the network leds depending on the current speed. */
++		crisv32_set_network_leds(CRIS_LED_ACTIVITY, dev);
++
++		/* Set the earliest time we may clear the LED */
++		np->leds->led_next_time = jiffies + NET_FLASH_TIME;
++		np->leds->led_active = 1;
++		np->leds->clear_led_timer.data = (unsigned long) dev;
++		mod_timer(&np->leds->clear_led_timer, jiffies + HZ/10);
++	}
++	spin_unlock_irqrestore(&np->leds->led_lock, flags);
++
++	return 0;
++}
++
++
++static void
++crisv32_eth_hw_send_packet(unsigned char *buf, int length, void *priv)
++{
++	struct crisv32_ethernet_local *np =
++		(struct crisv32_ethernet_local *) priv;
++
++	/* Configure the tx dma descriptor. */
++	np->active_tx_desc->descr.buf = (unsigned char *)virt_to_phys(buf);
++
++	np->active_tx_desc->descr.after = np->active_tx_desc->descr.buf +
++		length;
++	np->active_tx_desc->descr.intr = 1;
++	np->active_tx_desc->descr.out_eop = 1;
++
++	/* Move eol. */
++	np->active_tx_desc->descr.eol = 1;
++	flush_dma_descr(&np->active_tx_desc->descr, 1);
++
++	if (np->sender_started)
++		WARN_ON(!np->prev_tx_desc->descr.eol);
++	np->prev_tx_desc->descr.eol = 0;
++	flush_dma_descr(&np->prev_tx_desc->descr, 0);
++
++	/* Update pointers. */
++	np->prev_tx_desc = np->active_tx_desc;
++	np->active_tx_desc = phys_to_virt((int)np->active_tx_desc->descr.next);
++
++	/* Start DMA. */
++	crisv32_start_dma_out(np);
++}
++
++static void crisv32_start_dma_out(struct crisv32_ethernet_local *np)
++{
++	if (!np->sender_started) {
++		/* Start DMA for the first time. */
++		np->ctxt_out.saved_data =
++			(void *)virt_to_phys(&np->prev_tx_desc->descr);
++		np->ctxt_out.saved_data_buf = np->prev_tx_desc->descr.buf;
++		WARN_ON(!np->ctxt_out.saved_data_buf);
++
++		cris_flush_cache_range(&np->ctxt_out, sizeof np->ctxt_out);
++		REG_WR(dma, np->dma_out_inst, rw_group_down,
++		       (int) virt_to_phys(&np->ctxt_out));
++		DMA_WR_CMD(np->dma_out_inst, regk_dma_load_c);
++		DMA_WR_CMD(np->dma_out_inst, regk_dma_load_d | regk_dma_burst);
++		np->sender_started = 1;
++	} else {
++		DMA_CONTINUE_DATA(np->dma_out_inst);
++	}
++}
++
++/*
++ * Bring the transmitter back to life.
++ */
++static void
++crisv32_eth_do_tx_recovery(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	reg_eth_rw_clr_err clr_err;
++	reg_dma_rw_stat stat = {0};
++	unsigned long flags;
++	/* ACK urun and exc_col.  */
++	int ack_intr = 0x1800;
++	int do_full;
++
++	/* Give the tx recovery some time without link state polling.  */
++	if (!np->fixed_phy)
++		mod_timer(&np->speed_timer, jiffies + 4 * HZ);
++
++	np->tx_dma_restarts++;
++
++	spin_lock_irqsave(&np->lock, flags);
++
++	do_full = 1;
++	update_tx_stats(np);
++
++	/* Cancel ongoing frame.  */
++	crisv32_eth_tx_cancel_frame(np);
++
++	/* In case TR 125 just hit us.  */
++	DMA_WR_CMD(np->dma_out_inst, regk_dma_ack_pkt);
++	dma_wait_busy(np->dma_out_inst, 100);
++
++	/* At this point, the transmit block should be idle or waiting for us
++	   to clear the excessive collision error. Let's reset the DMA.  */
++	DMA_STOP(np->dma_out_inst);
++
++	crisv32_disconnect_eth_tx_dma(np);
++
++	/* Eat from the tx ring.  */
++	_crisv32_tx_ring_advance(np, 1);
++	np->do_tx_recovery++;
++
++	DMA_RESET(np->dma_out_inst);
++	do {
++		stat = REG_RD(dma, np->dma_out_inst, rw_stat);
++	} while (stat.mode != regk_dma_rst);
++
++	/* Next packet will restart output DMA. */
++	np->sender_started = 0;
++
++	crisv32_enable_tx_ints(np);
++
++	DMA_ENABLE(np->dma_out_inst);
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	DMA_WR_CMD(np->dma_out_inst, regk_dma_set_w_size4);
++#endif
++	DMA_CONTINUE(np->dma_out_inst);
++
++	/* Clear pending errors.  */
++	REG_WR_INT(eth, np->eth_inst, rw_ack_intr, ack_intr);
++	clr_err.clr = 1;
++	REG_WR(eth, np->eth_inst, rw_clr_err, clr_err);
++
++	/* Do a full reset of the MAC block.  */
++	if (do_full) {
++		np->tx_mac_resets++;
++		crisv32_eth_reset(np);
++	}
++
++	crisv32_connect_eth_tx_dma(np);
++
++	if (np->txpackets) {
++		WARN_ON(!np->catch_tx_desc->skb);
++		np->catch_tx_desc->descr.intr = 1;
++		np->catch_tx_desc->descr.out_eop = 1;
++
++		/* Start DMA for the first time. */
++		np->ctxt_out.saved_data =
++			(void *)virt_to_phys(&np->catch_tx_desc->descr);
++		np->ctxt_out.saved_data_buf = np->catch_tx_desc->descr.buf;
++		WARN_ON(!np->ctxt_out.saved_data_buf);
++		flush_dma_descr(&np->catch_tx_desc->descr, 0);
++		cris_flush_cache_range(&np->ctxt_out, sizeof np->ctxt_out);
++
++		REG_WR(dma, np->dma_out_inst, rw_group_down,
++		       (int) virt_to_phys(&np->ctxt_out));
++		DMA_WR_CMD(np->dma_out_inst, regk_dma_load_c);
++		DMA_WR_CMD(np->dma_out_inst, regk_dma_load_d | regk_dma_burst);
++		crisv32_eth_roll_tx_timer(np);
++		np->sender_started = 1;
++	}
++
++	if (np->txpackets && crisv32_eth_tx_ring_full(np))
++		netif_stop_queue(dev);
++	else
++		netif_wake_queue(dev);
++
++	spin_unlock_irqrestore(&np->lock, flags);
++}
++
++/*
++ * Set or clear the multicast filter for this adaptor.
++ * num_addrs == -1	Promiscuous mode, receive all packets
++ * num_addrs == 0	Normal mode, clear multicast list
++ * num_addrs > 0	Multicast mode, receive normal and MC packets,
++ *			and do best-effort filtering.
++ */
++static void crisv32_eth_set_rx_mode(struct net_device *dev)
++{
++	int num_addr = netdev_mc_count(dev);
++	unsigned long int lo_bits;
++	unsigned long int hi_bits;
++	reg_eth_rw_rec_ctrl rec_ctrl = {0};
++	reg_eth_rw_ga_lo ga_lo = {0};
++	reg_eth_rw_ga_hi ga_hi = {0};
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	if (dev->flags & IFF_PROMISC) {
++		/* Promiscuous mode. */
++		lo_bits = 0xfffffffful;
++		hi_bits = 0xfffffffful;
++
++		/* Enable individual receive. */
++		rec_ctrl = (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst,
++							rw_rec_ctrl);
++		rec_ctrl.individual = regk_eth_yes;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	} else if (dev->flags & IFF_ALLMULTI) {
++		/* Enable all multicasts. */
++		lo_bits = 0xfffffffful;
++		hi_bits = 0xfffffffful;
++
++		/* Disable individual receive */
++		rec_ctrl =
++		  (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++		rec_ctrl.individual = regk_eth_no;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	} else if (num_addr == 0) {
++		/* Normal, clear the mc list. */
++		lo_bits = 0x00000000ul;
++		hi_bits = 0x00000000ul;
++
++		/* Disable individual receive */
++		rec_ctrl =
++		  (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++		rec_ctrl.individual = regk_eth_no;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	} else {
++		/* MC mode, receive normal and MC packets. */
++		char hash_ix;
++		struct netdev_hw_addr *ha;
++		char *baddr;
++		lo_bits = 0x00000000ul;
++		hi_bits = 0x00000000ul;
++
++		netdev_for_each_mc_addr(ha, dev) {
++			/* Calculate the hash index for the GA registers. */
++			hash_ix = 0;
++			baddr = ha->addr;
++			hash_ix ^= (*baddr) & 0x3f;
++			hash_ix ^= ((*baddr) >> 6) & 0x03;
++			++baddr;
++			hash_ix ^= ((*baddr) << 2) & 0x03c;
++			hash_ix ^= ((*baddr) >> 4) & 0xf;
++			++baddr;
++			hash_ix ^= ((*baddr) << 4) & 0x30;
++			hash_ix ^= ((*baddr) >> 2) & 0x3f;
++			++baddr;
++			hash_ix ^= (*baddr) & 0x3f;
++			hash_ix ^= ((*baddr) >> 6) & 0x03;
++			++baddr;
++			hash_ix ^= ((*baddr) << 2) & 0x03c;
++			hash_ix ^= ((*baddr) >> 4) & 0xf;
++			++baddr;
++			hash_ix ^= ((*baddr) << 4) & 0x30;
++			hash_ix ^= ((*baddr) >> 2) & 0x3f;
++
++			hash_ix &= 0x3f;
++
++			if (hash_ix > 32)
++				hi_bits |= (1 << (hash_ix - 32));
++			else
++				lo_bits |= (1 << hash_ix);
++		}
++
++		/* Disable individual receive. */
++		rec_ctrl =
++		  (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, rw_rec_ctrl);
++		rec_ctrl.individual = regk_eth_no;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	}
++
++	ga_lo.table = (unsigned int) lo_bits;
++	ga_hi.table = (unsigned int) hi_bits;
++
++	REG_WR(eth, np->eth_inst, rw_ga_lo, ga_lo);
++	REG_WR(eth, np->eth_inst, rw_ga_hi, ga_hi);
++}
++
++static int
++crisv32_eth_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
++{
++	struct mii_ioctl_data *data = if_mii(ifr);
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	int old_autoneg;
++	int rc = 0;
++
++	spin_lock(&np->lock); /* Preempt protection */
++	switch (cmd) {
++		case SET_ETH_ENABLE_LEDS:
++			np->use_leds = 1;
++			break;
++		case SET_ETH_DISABLE_LEDS:
++			np->use_leds = 0;
++			break;
++		case SET_ETH_AUTONEG:
++			old_autoneg = np->autoneg_normal;
++			np->autoneg_normal = *(int*)data;
++			if (np->autoneg_normal != old_autoneg)
++				crisv32_eth_negotiate(dev);
++			break;
++		default:
++			rc = generic_mii_ioctl(&np->mii_if,
++					       if_mii(ifr), cmd, NULL);
++			break;
++	}
++	spin_unlock(&np->lock);
++	return rc;
++}
++
++static int crisv32_eth_get_settings(struct net_device *dev,
++				    struct ethtool_cmd *cmd)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	int err;
++
++	spin_lock_irq(&np->lock);
++	err = mii_ethtool_gset(&np->mii_if, cmd);
++	spin_unlock_irq(&np->lock);
++
++	/* The PHY may support 1000baseT, but the EtraxFS does not.  */
++	cmd->supported &= ~(SUPPORTED_1000baseT_Half
++			    | SUPPORTED_1000baseT_Full);
++	return err;
++}
++
++static int crisv32_eth_set_settings(struct net_device *dev,
++				    struct ethtool_cmd *ecmd)
++{
++	if (ecmd->autoneg == AUTONEG_ENABLE) {
++		crisv32_eth_set_duplex(dev, autoneg);
++		crisv32_eth_set_speed(dev, 0);
++	} else {
++		crisv32_eth_set_duplex(dev, ecmd->duplex);
++		crisv32_eth_set_speed(dev, ecmd->speed);
++	}
++
++	return 0;
++}
++
++static void crisv32_eth_get_drvinfo(struct net_device *dev,
++				    struct ethtool_drvinfo *info)
++{
++#ifdef CONFIG_ETRAXFS
++	strncpy(info->driver, "ETRAX FS", sizeof(info->driver) - 1);
++#else
++	strncpy(info->driver, "ARTPEC-3", sizeof(info->driver) - 1);
++#endif
++	strncpy(info->version, "$Revision: 1.197 $", sizeof(info->version) - 1);
++	strncpy(info->fw_version, "N/A", sizeof(info->fw_version) - 1);
++	strncpy(info->bus_info, "N/A", sizeof(info->bus_info) - 1);
++}
++
++static int crisv32_eth_get_ethtool_sset_count(struct net_device *dev,
++					      int stringset)
++{
++	if (stringset != ETH_SS_STATS)
++		return -EINVAL;
++
++	return ARRAY_SIZE(ethtool_stats_keys);
++}
++
++static void crisv32_eth_get_ethtool_stats(struct net_device *dev,
++					  struct ethtool_stats *stats,
++					  u64 *data)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data[0] = np->tx_dma_restarts;
++	data[1] = np->tx_mac_resets;
++	data[2] = np->rx_dma_restarts;
++	data[3] = np->rx_dma_timeouts;
++	data[4] = np->rx_restarts_dropped;
++}
++
++static void crisv32_eth_get_strings(struct net_device *dev,
++				    u32 stringset, u8 *data)
++{
++	switch (stringset) {
++		case ETH_SS_STATS:
++			memcpy(data, &ethtool_stats_keys,
++			       sizeof(ethtool_stats_keys));
++			break;
++		default:
++			WARN_ON(1);
++			break;
++	}
++}
++
++static int crisv32_eth_nway_reset(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	if (np->current_duplex == autoneg && np->current_speed_selection == 0)
++		crisv32_eth_negotiate(dev);
++	return 0;
++}
++/* The FS/A3 ethernet block has 23 32-bit config registers.  */
++/* plus 2 dma_descr_context */
++/* plus 2 sets of ring pointers (active, prev, last) */
++/* plus 2 sets of DMA registers 40*4 bytes = 0xA0 */
++#define ETRAX_ETH_REGDUMP_LEN (23 * 4 + 2 * sizeof (dma_descr_context) + 2*3*4 + 2*0xA0)
++static int crisv32_eth_get_regs_len(struct net_device *dev)
++{
++	return ETRAX_ETH_REGDUMP_LEN;
++}
++
++static void crisv32_eth_get_regs(struct net_device *dev,
++				 struct ethtool_regs *regs, void *_p)
++{
++	u32 *p = _p;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	int i;
++
++	/* Let's call this major version 0, minor version 1 with some
++	 * undecided field separation in the version data.  Previously
++	 * only the eth regs were dumped (version=0: maj 0, min 0).*/
++	regs->version = 1;
++	memset(p, 0, ETRAX_ETH_REGDUMP_LEN);
++
++#define GET_REG32_LOOP(base, len)				\
++	do {							\
++		for (i = 0; i < len; i += 4)			\
++			*(p)++ = REG_READ(u32, (base) + i);	\
++	 } while (0)
++
++	GET_REG32_LOOP(np->eth_inst, 0x30);
++	/* Do not dump registers with read side effects.  */
++	GET_REG32_LOOP(np->eth_inst + 0x34, 1);
++	GET_REG32_LOOP(np->eth_inst + 0x3c, 1);
++	GET_REG32_LOOP(np->eth_inst + 0x44, 0x5c - 0x44);
++
++
++	memcpy(p, &np->ctxt_out, sizeof (dma_descr_context));
++	p += sizeof (dma_descr_context)/4;
++	*(p++) = (u32) np->active_tx_desc;
++	*(p++) = (u32) np->prev_tx_desc;
++	*(p++) = (u32) np->catch_tx_desc;
++
++	GET_REG32_LOOP(np->dma_out_inst, 0xa0);
++
++	memcpy(p, &np->ctxt_in, sizeof (dma_descr_context));
++	p += sizeof (dma_descr_context)/4;
++	*(p++) = (u32)np->active_rx_desc;
++	*(p++) = (u32)np->prev_rx_desc;
++	*(p++) = (u32)np->last_rx_desc;
++
++	GET_REG32_LOOP(np->dma_in_inst, 0xa0);
++#undef GET_REG32_LOOP
++}
++
++static struct ethtool_ops crisv32_ethtool_ops = {
++	.get_settings		= crisv32_eth_get_settings,
++	.set_settings		= crisv32_eth_set_settings,
++	.get_drvinfo		= crisv32_eth_get_drvinfo,
++	.get_regs_len		= crisv32_eth_get_regs_len,
++	.get_regs		= crisv32_eth_get_regs,
++	.nway_reset		= crisv32_eth_nway_reset,
++	.get_link		= ethtool_op_get_link,
++	.get_strings		= crisv32_eth_get_strings,
++	.get_ethtool_stats	= crisv32_eth_get_ethtool_stats,
++	.get_sset_count		= crisv32_eth_get_ethtool_sset_count
++};
++
++/* Is this function really needed? Use ethtool instead? */
++static int crisv32_eth_set_config(struct net_device *dev, struct ifmap *map)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	spin_lock(&np->lock); /* Preempt protection */
++
++	switch (map->port) {
++		case IF_PORT_UNKNOWN:
++			/* Use autoneg */
++			crisv32_eth_set_speed(dev, 0);
++			crisv32_eth_set_duplex(dev, autoneg);
++			break;
++		case IF_PORT_10BASET:
++			crisv32_eth_set_speed(dev, 10);
++			crisv32_eth_set_duplex(dev, autoneg);
++			break;
++		case IF_PORT_100BASET:
++		case IF_PORT_100BASETX:
++			crisv32_eth_set_speed(dev, 100);
++			crisv32_eth_set_duplex(dev, autoneg);
++			break;
++		case IF_PORT_100BASEFX:
++		case IF_PORT_10BASE2:
++		case IF_PORT_AUI:
++			spin_unlock(&np->lock);
++			return -EOPNOTSUPP;
++			break;
++		default:
++			printk(KERN_ERR "%s: Invalid media selected",
++			       dev->name);
++			spin_unlock(&np->lock);
++			return -EINVAL;
++	}
++	spin_unlock(&np->lock);
++	return 0;
++}
++
++static void crisv32_eth_negotiate(struct net_device *dev)
++{
++	unsigned short data;
++	unsigned short ctrl1000;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE);
++	ctrl1000 = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					    MII_CTRL1000);
++
++	/* Make all capabilities available */
++	data |= ADVERTISE_10HALF | ADVERTISE_10FULL |
++		ADVERTISE_100HALF | ADVERTISE_100FULL;
++	ctrl1000 |= ADVERTISE_1000HALF | ADVERTISE_1000FULL;
++
++	/* Remove the speed capabilities that we that do not want */
++	switch (np->current_speed_selection) {
++		case 10 :
++			data &= ~(ADVERTISE_100HALF | ADVERTISE_100FULL);
++			ctrl1000 &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL);
++			break;
++		case 100 :
++			data &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL);
++			ctrl1000 &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL);
++			break;
++		case 1000 :
++			data &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL |
++				  ADVERTISE_100HALF | ADVERTISE_100FULL);
++			break;
++	}
++
++	/* Remove the duplex capabilites that we do not want */
++	if (np->current_duplex == full) {
++		data &= ~(ADVERTISE_10HALF | ADVERTISE_100HALF);
++		ctrl1000 &= ~(ADVERTISE_1000HALF);
++	}
++	else if (np->current_duplex == half) {
++		data &= ~(ADVERTISE_10FULL | ADVERTISE_100FULL);
++		ctrl1000 &= ~(ADVERTISE_1000FULL);
++	}
++
++	crisv32_eth_set_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE, data);
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	crisv32_eth_set_mdio_reg(dev, np->mii_if.phy_id,
++				 MII_CTRL1000, ctrl1000);
++#endif
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
++	if (np->autoneg_normal) {
++		/* Renegotiate with link partner */
++		data |= BMCR_ANENABLE | BMCR_ANRESTART;
++	} else {
++		/* Don't negitiate speed or duplex */
++		data &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
++
++		/* Set speed and duplex static */
++		if (np->current_speed_selection == 10) {
++			data &= ~(BMCR_SPEED100 | BMCR_SPEED1000);
++		}
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++		else if (np->current_speed_selection == 1000) {
++			data &= ~BMCR_SPEED100;
++			data |=  BMCR_SPEED1000;
++		}
++#endif
++		else {
++			data |= BMCR_SPEED100;
++			data &= ~BMCR_SPEED1000;
++		}
++
++		if (np->current_duplex != full) {
++			data &= ~BMCR_FULLDPLX;
++		} else {
++			data |= BMCR_FULLDPLX;
++		}
++	}
++	crisv32_eth_set_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR, data);
++}
++
++static void crisv32_eth_check_speed(unsigned long idev)
++{
++#ifndef CONFIG_ETRAX_NO_PHY
++	static int led_initiated = 0;
++	struct net_device *dev = (struct net_device *) idev;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	unsigned long data;
++	int old_speed;
++	unsigned long flags;
++
++	BUG_ON(!np);
++	BUG_ON(!np->transceiver);
++
++	spin_lock(&np->transceiver_lock);
++
++	old_speed = np->current_speed;
++
++	/* Do a fake read. This is needed for DM9161, otherwise the link will
++	 * go up and down all the time.
++	 */
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMSR);
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMSR);
++
++	if (!(data & BMSR_LSTATUS))
++		np->current_speed = 0;
++	else
++		np->transceiver->check_speed(dev);
++
++	spin_lock_irqsave(&np->leds->led_lock, flags);
++	if ((old_speed != np->current_speed) || !led_initiated) {
++		led_initiated = 1;
++		np->leds->clear_led_timer.data = (unsigned long) dev;
++		if (np->current_speed) {
++			if (!np->link)
++				netif_carrier_on(dev);
++			crisv32_set_network_leds(CRIS_LED_LINK, dev);
++			np->link = 1;
++		} else {
++			if (np->link)
++				netif_carrier_off(dev);
++			crisv32_set_network_leds(CRIS_LED_NOLINK, dev);
++			np->link = 0;
++		}
++	}
++	spin_unlock_irqrestore(&np->leds->led_lock, flags);
++
++	/* Reinitialize the timer. */
++	np->speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL;
++	add_timer(&np->speed_timer);
++
++	spin_unlock(&np->transceiver_lock);
++#endif
++}
++
++static void crisv32_eth_set_speed(struct net_device *dev, unsigned long speed)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	spin_lock(&np->transceiver_lock);
++	if (np->current_speed_selection != speed) {
++		np->current_speed_selection = speed;
++		crisv32_eth_negotiate(dev);
++	}
++	spin_unlock(&np->transceiver_lock);
++}
++
++static void crisv32_eth_check_duplex(unsigned long idev)
++{
++#ifndef CONFIG_ETRAX_NO_PHY
++	struct net_device *dev = (struct net_device *) idev;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	reg_eth_rw_rec_ctrl rec_ctrl;
++	int old_duplex = np->full_duplex;
++
++	np->transceiver->check_duplex(dev);
++
++	if (old_duplex != np->full_duplex) {
++		/* Duplex changed. */
++		rec_ctrl = (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst,
++							rw_rec_ctrl);
++		rec_ctrl.duplex = np->full_duplex;
++		REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl);
++	}
++
++	/* Reinitialize the timer. */
++	np->duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL;
++	add_timer(&np->duplex_timer);
++#endif
++}
++
++static void
++crisv32_eth_set_duplex(struct net_device *dev, enum duplex new_duplex)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	spin_lock(&np->transceiver_lock);
++	if (np->current_duplex != new_duplex) {
++		np->current_duplex = new_duplex;
++		crisv32_eth_negotiate(dev);
++	}
++	spin_unlock(&np->transceiver_lock);
++}
++
++static int crisv32_eth_probe_transceiver(struct net_device *dev)
++{
++#ifndef CONFIG_ETRAX_NO_PHY
++	unsigned int phyid_high;
++	unsigned int phyid_low;
++	unsigned int oui;
++	struct transceiver_ops *ops = NULL;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	/* Probe MDIO physical address. */
++	for (np->mii_if.phy_id = 0;
++	     np->mii_if.phy_id <= 31; np->mii_if.phy_id++) {
++		if (crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMSR)
++		    != 0xffff)
++			break;
++	}
++
++	if (np->mii_if.phy_id == 32)
++		return -ENODEV;
++
++	/* Get manufacturer. */
++	phyid_high = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					      MII_PHYSID1);
++	phyid_low = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					     MII_PHYSID2);
++
++	oui = (phyid_high << 6) | (phyid_low >> 10);
++
++	for (ops = &transceivers[0]; ops->oui; ops++) {
++		if (ops->oui == oui)
++			break;
++	}
++
++	np->transceiver = ops;
++
++	if (oui == DM9161_OUI) {
++		/* Do not bypass the scrambler/descrambler, this is needed
++		 * to make 10Mbit work.
++		 */
++		crisv32_eth_set_mdio_reg(dev, np->mii_if.phy_id,
++					 MII_DM9161_SCR,MII_DM9161_SCR_INIT);
++		/* Clear 10BTCSR to default */
++		crisv32_eth_set_mdio_reg(dev, np->mii_if.phy_id,
++					 MII_DM9161_10BTCSR,
++					 MII_DM9161_10BTCSR_INIT);
++	}
++	return 0;
++#else
++	return -ENODEV;
++#endif
++}
++
++#ifndef CONFIG_ETRAX_NO_PHY
++static void generic_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE);
++	if ((data & ADVERTISE_100FULL) ||
++	    (data & ADVERTISE_100HALF))
++		np->current_speed = 100;
++	else
++		np->current_speed = 10;
++}
++
++static void generic_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE);
++	if ((data & ADVERTISE_10FULL) ||
++	    (data & ADVERTISE_100FULL))
++		np->full_duplex = 1;
++	else
++		np->full_duplex = 0;
++}
++
++static void broadcom_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_AUX_CTRL_STATUS_REG);
++	np->current_speed = (data & MDIO_BC_SPEED ? 100 : 10);
++}
++
++static void broadcom_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_AUX_CTRL_STATUS_REG);
++	np->full_duplex = (data & MDIO_BC_FULL_DUPLEX_IND) ? 1 : 0;
++}
++
++static void tdk_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_TDK_DIAGNOSTIC_REG);
++	np->current_speed = (data & MDIO_TDK_DIAGNOSTIC_RATE ? 100 : 10);
++}
++
++static void tdk_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_TDK_DIAGNOSTIC_REG);
++	np->full_duplex = (data & MDIO_TDK_DIAGNOSTIC_DPLX) ? 1 : 0;
++
++}
++
++static void intel_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_INT_STATUS_REG_2);
++	np->current_speed = (data & MDIO_INT_SPEED ? 100 : 10);
++}
++
++static void intel_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_INT_STATUS_REG_2);
++	np->full_duplex = (data & MDIO_INT_FULL_DUPLEX_IND) ? 1 : 0;
++}
++
++static void national_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_NAT_LINK_AN_REG);
++	if (data & MDIO_NAT_1000)
++		np->current_speed = 1000;
++	else if (data & MDIO_NAT_100)
++		np->current_speed = 100;
++	else
++		np->current_speed = 10;
++}
++
++static void national_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_NAT_LINK_AN_REG);
++	if (data & MDIO_NAT_FULL_DUPLEX_IND)
++		np->full_duplex = 1;
++	else
++		np->full_duplex = 0;
++}
++
++static void vitesse_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_VIT_AUX_STAT);
++	if ((data & 0x18) == MDIO_VIT_1000)
++		np->current_speed = 1000;
++	else if ((data & 0x18) == MDIO_VIT_100)
++		np->current_speed = 100;
++	else
++		np->current_speed = 10;
++}
++
++static void vitesse_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++					MDIO_VIT_AUX_STAT);
++	if (data & 0x20)
++		np->full_duplex = 1;
++	else
++		np->full_duplex = 0;
++}
++
++static void davicom_check_speed(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
++	np->current_speed = (data & BMCR_SPEED100) ? 100 : 10;
++}
++
++static void davicom_check_duplex(struct net_device *dev)
++{
++	unsigned long data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
++	np->full_duplex = (data & BMCR_FULLDPLX) ? 1 : 0;
++}
++#endif
++
++#if 0
++static void crisv32_eth_reset_tranceiver(struct net_device *dev)
++{
++	int i;
++	unsigned short cmd;
++	unsigned short data;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR);
++
++	cmd = (MDIO_START << 14)
++		| (MDIO_WRITE << 12)
++		| (np->mii_if.phy_id << 7)
++		| (MII_BMCR << 2);
++
++	crisv32_eth_send_mdio_cmd(dev, cmd, 1);
++
++	data |= 0x8000;
++
++	/* Magic value is number of bits. */
++	for (i = 15; i >= 0; i--)
++		crisv32_eth_send_mdio_bit(dev, GET_BIT(i, data));
++}
++#endif
++
++static int
++crisv32_eth_get_mdio_reg(struct net_device *dev, int phyid, int reg_num)
++{
++	int i;
++	unsigned short cmd;	/* Data to be sent on MDIO port. */
++	unsigned short data;	/* Data read from MDIO. */
++
++#ifdef CONFIG_ETRAX_NO_PHY
++	return 0;
++#endif
++
++	/* Start of frame, OP Code, Physical Address, Register Address. */
++	cmd = (MDIO_START << 14)
++		| (MDIO_READ << 12)
++		| (phyid << 7)
++		| (reg_num << 2);
++
++	crisv32_eth_send_mdio_cmd(dev, cmd, 0);
++
++	data = 0;
++
++	/* Receive data. Magic value is number of bits. */
++	for (i = 15; i >= 0; i--)
++		data |= (crisv32_eth_receive_mdio_bit(dev) << i);
++
++	return data;
++}
++
++static void
++crisv32_eth_set_mdio_reg(struct net_device *dev, int phyid, int reg, int value)
++{
++	int bitCounter;
++	unsigned short cmd;
++
++#ifdef CONFIG_ETRAX_NO_PHY
++	return;
++#endif
++	cmd = (MDIO_START << 14)
++		| (MDIO_WRITE << 12)
++		| (phyid << 7)
++		| (reg << 2);
++
++	crisv32_eth_send_mdio_cmd(dev, cmd, 1);
++
++	/* Data... */
++	for (bitCounter=15; bitCounter>=0 ; bitCounter--) {
++		crisv32_eth_send_mdio_bit(dev, GET_BIT(bitCounter, value));
++	}
++}
++
++static void
++crisv32_eth_send_mdio_cmd(struct net_device *dev, unsigned short cmd,
++			  int write_cmd)
++{
++	int i;
++	unsigned char data = 0x2;
++
++	/* Preamble. Magic value is number of bits. */
++	for (i = 31; i >= 0; i--)
++		crisv32_eth_send_mdio_bit(dev, GET_BIT(i, MDIO_PREAMBLE));
++
++	for (i = 15; i >= 2; i--)
++		crisv32_eth_send_mdio_bit(dev, GET_BIT(i, cmd));
++
++	/* Turnaround. */
++	for (i = 1; i >= 0; i--)
++		if (write_cmd)
++			crisv32_eth_send_mdio_bit(dev, GET_BIT(i, data));
++		else
++			crisv32_eth_receive_mdio_bit(dev);
++}
++
++static void crisv32_eth_send_mdio_bit(struct net_device *dev, unsigned char bit)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	reg_eth_rw_mgm_ctrl mgm_ctrl = {
++		.mdoe = regk_eth_yes,
++		.mdio = bit & 1
++	};
++
++	REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl);
++
++	udelay(1);
++
++	mgm_ctrl.mdc = 1;
++	REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl);
++
++	udelay(1);
++}
++
++static unsigned char crisv32_eth_receive_mdio_bit(struct net_device *dev)
++{
++	reg_eth_r_stat stat;
++	reg_eth_rw_mgm_ctrl mgm_ctrl = {0};
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++
++	REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl);
++	stat = REG_RD(eth, np->eth_inst, r_stat);
++
++	udelay(1);
++
++	mgm_ctrl.mdc = 1;
++	REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl);
++
++	udelay(1);
++	return stat.mdio;
++}
++
++static void crisv32_clear_network_leds(unsigned long priv)
++{
++	struct net_device *dev = (struct net_device *)priv;
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	unsigned long flags;
++
++	spin_lock_irqsave(&np->leds->led_lock, flags);
++	if (np->leds->led_active && time_after(jiffies,
++					       np->leds->led_next_time)) {
++		crisv32_set_network_leds(CRIS_LED_NOACTIVITY, dev);
++
++		/* Set the earliest time we may set the LED */
++		np->leds->led_next_time = jiffies + NET_FLASH_PAUSE;
++		np->leds->led_active = 0;
++	}
++	spin_unlock_irqrestore(&np->leds->led_lock, flags);
++}
++
++static void crisv32_set_network_leds(int active, struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	int light_leds = 0;
++
++	if (np->leds->ledgrp == CRIS_LED_GRP_NONE)
++		return;
++
++	if (!np->use_leds)
++		return;
++
++	if (active == CRIS_LED_NOLINK) {
++		if (dev == crisv32_dev[0])
++			np->leds->ifisup[0] = 0;
++		else
++			np->leds->ifisup[1] = 0;
++	}
++	else if (active == CRIS_LED_LINK) {
++		if (dev == crisv32_dev[0])
++			np->leds->ifisup[0] = 1;
++		else
++			np->leds->ifisup[1] = 1;
++#if defined(CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK)
++		light_leds = 1;
++	} else {
++		light_leds = (active == CRIS_LED_NOACTIVITY);
++#elif defined(CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY)
++		light_leds = 0;
++	} else {
++		light_leds = (active == CRIS_LED_ACTIVITY);
++#else
++#error "Define either CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK or CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY"
++#endif
++	}
++}
++
++#ifdef CONFIG_NET_POLL_CONTROLLER
++static void crisv32_netpoll(struct net_device *netdev)
++{
++	crisv32rx_eth_interrupt(DMA0_INTR_VECT, netdev);
++}
++#endif
++
++#ifdef CONFIG_CPU_FREQ
++static int crisv32_ethernet_freq_notifier(struct notifier_block *nb,
++					  unsigned long val, void *data)
++{
++	struct cpufreq_freqs *freqs = data;
++	int i;
++	if (val != CPUFREQ_POSTCHANGE)
++		return 0;
++
++	for (i = 0; i < 2; i++) {
++		struct net_device *dev = crisv32_dev[i];
++		unsigned short data;
++		if (dev == NULL)
++			continue;
++
++		data = crisv32_eth_get_mdio_reg(dev, np->mii_if.phy_id,
++				MII_BMCR);
++		if (freqs->new == 200000)
++			data &= ~BMCR_PDOWN;
++		else
++			data |= BMCR_PDOWN;
++		crisv32_eth_set_mdio_reg(dev, np->mii_if.phy_id,
++				MII_BMCR, data);
++	}
++	return 0;
++}
++#endif
++
++#if 0
++/*
++ * Must be called with the np->lock held.
++ */
++static void crisv32_ethernet_bug(struct net_device *dev)
++{
++	struct crisv32_ethernet_local *np = netdev_priv(dev);
++	dma_descr_data *dma_pos;
++	dma_descr_data *in_dma_pos;
++	reg_dma_rw_stat stat = {0};
++	reg_dma_rw_stat in_stat = {0};
++	int i;
++
++	/* Get the current output dma position. */
++	stat = REG_RD(dma, np->dma_out_inst, rw_stat);
++
++	dma_pos = phys_to_virt(REG_RD_INT(dma, np->dma_out_inst, rw_data));
++	in_dma_pos = phys_to_virt(REG_RD_INT(dma, np->dma_in_inst, rw_data));
++	in_stat = REG_RD(dma, np->dma_in_inst, rw_stat);
++
++	printk("%s:\n"
++	       "stat.list_state=%x\n"
++	       "stat.mode=%x\n"
++	       "stat.stream_cmd_src=%x\n"
++	       "dma_pos=%x\n"
++	       "tx catch=%x active=%x\n"
++	       "packets=%d queue=%d sender_started=%d\n"
++	       "intr_vect.r_vect=%x\n"
++	       "dma.r_masked_intr=%x dma.rw_ack_intr=%x "
++	       "dma.r_intr=%x dma.rw_intr_masked=%x\n"
++	       "eth.r_stat=%x\n",
++	       __func__,
++	       stat.list_state, stat.mode, stat.stream_cmd_src,
++	       (unsigned int)dma_pos,
++	       (unsigned int)&np->catch_tx_desc->descr,
++	       (unsigned int)&np->active_tx_desc->descr,
++	       np->txpackets,
++	       netif_queue_stopped(dev), np->sender_started,
++	       REG_RD_INT(intr_vect, regi_irq, r_vect),
++	       REG_RD_INT(dma, np->dma_out_inst, r_masked_intr),
++	       REG_RD_INT(dma, np->dma_out_inst, rw_ack_intr),
++	       REG_RD_INT(dma, np->dma_out_inst, r_intr),
++	       REG_RD_INT(dma, np->dma_out_inst, rw_intr_mask),
++	       REG_RD_INT(eth, np->eth_inst, r_stat));
++
++	printk("in_stat.list_state=%x\n"
++	       "in_stat.mode=%x\n"
++	       "in_stat.stream_cmd_src=%x\n"
++	       "in_dma_pos=%x\n"
++	       "rx last=%x prev=%x active=%x\n",
++	       in_stat.list_state, in_stat.mode, in_stat.stream_cmd_src,
++	       (unsigned int)in_dma_pos,
++	       (unsigned int)&np->last_rx_desc->descr,
++	       (unsigned int)&np->prev_rx_desc->descr,
++	       (unsigned int)&np->active_rx_desc->descr);
++
++#if 0
++	printk("rx-descriptors:\n");
++	for (i = 0; i < NBR_RX_DESC; i++) {
++		printk("rxdesc[%d]=0x%x\n", i, (unsigned int)
++		       virt_to_phys(&np->dma_rx_descr_list[i].descr));
++		printk("rxdesc[%d].skb=0x%x\n", i,
++		       (unsigned int)np->dma_rx_descr_list[i].skb);
++		printk("rxdesc[%d].buf=0x%x\n", i,
++		       (unsigned int)np->dma_rx_descr_list[i].descr.buf);
++		printk("rxdesc[%d].after=0x%x\n", i,
++		       (unsigned int)np->dma_rx_descr_list[i].descr.after);
++		printk("rxdesc[%d].intr=%x\n", i,
++		       np->dma_rx_descr_list[i].descr.intr);
++		printk("rxdesc[%d].eol=%x\n", i,
++		       np->dma_rx_descr_list[i].descr.eol);
++		printk("rxdesc[%d].out_eop=%x\n", i,
++		       np->dma_rx_descr_list[i].descr.out_eop);
++		printk("rxdesc[%d].in_eop=%x\n", i,
++		       np->dma_rx_descr_list[i].descr.in_eop);
++		printk("rxdesc[%d].wait=%x\n", i,
++		       np->dma_rx_descr_list[i].descr.wait);
++	}
++#endif
++
++#if 1
++	printk("tx-descriptors:\n");
++	for (i = 0; i < NBR_TX_DESC; i++) {
++		printk("txdesc[%d]=0x%x\n", i, (unsigned int)
++		       virt_to_phys(&np->dma_tx_descr_list[i].descr));
++		printk("txdesc[%d].skb=0x%x\n", i,
++		       (unsigned int)np->dma_tx_descr_list[i].skb);
++		printk("txdesc[%d].buf=0x%x\n", i,
++		       (unsigned int)np->dma_tx_descr_list[i].descr.buf);
++		printk("txdesc[%d].after=0x%x\n", i,
++		       (unsigned int)np->dma_tx_descr_list[i].descr.after);
++		printk("txdesc[%d].intr=%x\n", i,
++		       np->dma_tx_descr_list[i].descr.intr);
++		printk("txdesc[%d].eol=%x\n", i,
++		       np->dma_tx_descr_list[i].descr.eol);
++		printk("txdesc[%d].out_eop=%x\n", i,
++		       np->dma_tx_descr_list[i].descr.out_eop);
++		printk("txdesc[%d].in_eop=%x\n", i,
++		       np->dma_tx_descr_list[i].descr.in_eop);
++		printk("txdesc[%d].wait=%x\n", i,
++		       np->dma_tx_descr_list[i].descr.wait);
++	}
++#endif
++}
++#endif
++
++static int __init crisv32_boot_setup(char *str)
++{
++	struct sockaddr sa = {0};
++	int i;
++
++	/* Parse the colon separated Ethernet station address */
++	for (i = 0; i <  ETH_ALEN; i++) {
++		unsigned int tmp;
++		if (sscanf(str + 3*i, "%2x", &tmp) != 1) {
++			printk(KERN_WARNING "Malformed station address");
++			return 0;
++		}
++		sa.sa_data[i] = (char)tmp;
++	}
++
++	default_mac_iface0 = sa;
++	return 1;
++}
++
++__setup("crisv32_eth=", crisv32_boot_setup);
++
++module_init(crisv32_ethernet_init);
+diff -Nur linux-4.4.6.orig/drivers/net/cris/eth_v32.h linux-4.4.6/drivers/net/cris/eth_v32.h
+--- linux-4.4.6.orig/drivers/net/cris/eth_v32.h	1970-01-01 01:00:00.000000000 +0100
++++ linux-4.4.6/drivers/net/cris/eth_v32.h	2016-03-20 15:09:24.046562363 +0100
+@@ -0,0 +1,291 @@
++/*
++ * Definitions for ETRAX FS ethernet driver.
++ *
++ * Copyright (C) 2003, 2004, 2005 Axis Communications.
++ */
++
++#ifndef _ETRAX_ETHERNET_H_
++#define _ETRAX_ETHERNET_H_
++
++#include <hwregs/dma.h>
++
++#define MAX_MEDIA_DATA_SIZE 1522	/* Max packet size. */
++
++#define NBR_RX_DESC 128		/* Number of RX descriptors. */
++#define NBR_TX_DESC 16		/* Number of TX descriptors. */
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++#define NBR_INTMEM_RX_DESC 16	/* Number of RX descriptors in int. mem.
++				 * when running in gigabit mode.
++				 * Should be less then NBR_RX_DESC
++				 */
++#define NBR_INTMEM_TX_BUF 4	/* Number of TX buffers in int. mem
++				 * when running in gigabit mode.
++				 * Should be less than NBR_TX_DESC
++				 */
++#endif
++
++/* Large packets are sent directly to upper layers while small packets
++ * are copied (to reduce memory waste).  The following constant
++ * decides the breakpoint.
++ */
++#define RX_COPYBREAK        (256)
++
++#define ETHER_HEAD_LEN      (14)
++
++/*
++ * MDIO constants.
++ */
++#define MDIO_START                          0x1
++#define MDIO_READ                           0x2
++#define MDIO_WRITE                          0x1
++#define MDIO_PREAMBLE              0xfffffffful
++
++/* Broadcom specific */
++#define MDIO_AUX_CTRL_STATUS_REG           0x18
++#define MDIO_BC_FULL_DUPLEX_IND             0x1
++#define MDIO_BC_SPEED                       0x2
++
++/* TDK specific */
++#define MDIO_TDK_DIAGNOSTIC_REG              18
++#define MDIO_TDK_DIAGNOSTIC_RATE          0x400
++#define MDIO_TDK_DIAGNOSTIC_DPLX          0x800
++
++/*Intel LXT972A specific*/
++#define MDIO_INT_STATUS_REG_2		   0x0011
++#define MDIO_INT_FULL_DUPLEX_IND ( 0x0001 << 9  )
++#define MDIO_INT_SPEED		 ( 0x0001 << 14 )
++
++/*National Semiconductor DP83865 specific*/
++#define MDIO_NAT_LINK_AN_REG              0x11
++#define MDIO_NAT_1000            (0x0001 << 4)
++#define MDIO_NAT_100             (0x0001 << 3)
++#define MDIO_NAT_FULL_DUPLEX_IND (0x0001 << 1)
++
++/* Vitesse VCS8641 specific */
++#define MDIO_VIT_AUX_STAT 0x1c
++#define MDIO_VIT_1000            (0x2 << 3)
++#define MDIO_VIT_100             (0x1 << 3)
++#define MDIO_VIT_10              0
++#define MDIO_VIT_FD              (0x1 << 5)
++
++/* Davicom DM9161 specific */
++#define DM9161_OUI               0x606E
++#define MII_DM9161_SCR           0x10
++#define MII_DM9161_SCR_INIT      0x0610
++#define MII_DM9161_SCR_RMII      0x0100
++#define MII_DM9161_10BTCSR       0x12
++#define MII_DM9161_10BTCSR_INIT  0x7800
++
++/* Network flash constants */
++#define NET_FLASH_TIME                  (HZ/50)	/* 20 ms */
++#define NET_FLASH_PAUSE                 (HZ/100)	/* 10 ms */
++#define NET_LINK_UP_CHECK_INTERVAL	(2*HZ)	/* 2 seconds. */
++#define NET_DUPLEX_CHECK_INTERVAL	(2*HZ)	/* 2 seconds. */
++
++/* Duplex settings. */
++enum duplex {
++	half,
++	full,
++	autoneg
++};
++
++/* Some transceivers requires special handling. */
++struct transceiver_ops {
++	unsigned int oui;
++	void (*check_speed) (struct net_device * dev);
++	void (*check_duplex) (struct net_device * dev);
++};
++
++typedef struct crisv32_eth_descr {
++	dma_descr_data descr __attribute__ ((__aligned__(32)));
++	struct sk_buff *skb;
++	unsigned char *linearized_packet;
++} crisv32_eth_descr;
++
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++struct tx_buffer_list {
++	struct tx_buffer_list *next;
++	unsigned char *buf;
++	char free;
++};
++#endif
++
++/* LED stuff */
++#define CRIS_LED_GRP_0 0
++#define CRIS_LED_GRP_1 1
++#define CRIS_LED_GRP_NONE 2
++
++#define CRIS_LED_ACTIVITY   0
++#define CRIS_LED_NOACTIVITY 1
++#define CRIS_LED_LINK       2
++#define CRIS_LED_NOLINK     3
++
++struct crisv32_eth_leds {
++	unsigned int ledgrp;
++	int led_active;
++	unsigned long led_next_time;
++	struct timer_list clear_led_timer;
++	spinlock_t led_lock;	/* Protect LED state */
++	int ifisup[2];
++};
++
++/* Information that need to be kept for each device. */
++struct crisv32_ethernet_local {
++	/* FIXME: These align attributes don't really help. If they are really
++	 * needed alignment has to be enforced at runtime, these objects
++	 * are dynamically allocated.  */
++	dma_descr_context ctxt_in __attribute__ ((__aligned__(32)));
++	dma_descr_context ctxt_out __attribute__ ((__aligned__(32)));
++
++	crisv32_eth_descr dma_rx_descr_list[NBR_RX_DESC];
++	crisv32_eth_descr dma_tx_descr_list[NBR_TX_DESC];
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++	struct tx_buffer_list tx_intmem_buf_list[NBR_INTMEM_TX_BUF];
++	struct tx_buffer_list *intmem_tx_buf_active;
++	struct tx_buffer_list *intmem_tx_buf_catch;
++	int gigabit_mode;
++#endif
++	/* Transmit data path.  */
++	int dma_out_inst;
++	int sender_started;
++
++	/* TX-ring state.  */
++	crisv32_eth_descr *active_tx_desc;
++	crisv32_eth_descr *prev_tx_desc;
++	crisv32_eth_descr *catch_tx_desc;
++	int txpackets;
++	int retrans;
++	int do_tx_recovery;
++	struct timer_list transmit_timer;
++
++	/* Receive data path.  */
++	struct napi_struct napi;
++	int dma_in_inst;
++
++	/* RX-ring state.  */
++	crisv32_eth_descr *active_rx_desc;
++	crisv32_eth_descr *prev_rx_desc;
++	crisv32_eth_descr *last_rx_desc;
++
++	unsigned long newbuf;
++	u8 new_rx_package;
++	u8 pending_overrun;
++	u8 overrun_set;
++	u8 link;
++	int napi_processing;
++	struct timer_list receive_timer;
++	struct work_struct receive_work;
++	reg_eth_rw_rec_ctrl saved_rec_ctrl;
++	int saved_ga_lo;
++	int saved_ga_hi;
++	int do_rx_recovery;
++
++	/* Control paths.  */
++	spinlock_t lock;
++	struct net_device *dev;
++	int eth_inst;
++
++	/* Toggle network LEDs usage at runtime */
++	int use_leds;
++	struct crisv32_eth_leds *leds;
++
++	/* PHY control.  */
++	int fixed_phy;
++	spinlock_t transceiver_lock;	/* Protect transceiver state. */
++	struct transceiver_ops *transceiver;
++	struct mii_if_info mii_if;
++
++	/* Specifies if we should do autonegotiation or not.
++	 * TODO: This ad-hoc hack should be removed. Ethtool already supports
++	 *       this kind of control.
++	 */
++	int autoneg_normal;
++
++	struct timer_list duplex_timer;
++	int full_duplex;
++	enum duplex current_duplex;
++
++	struct timer_list speed_timer;
++	int current_speed;	/* Speed read from tranceiver */
++	int current_speed_selection;	/* Speed selected by user */
++
++	/* Statistics.  */
++	u64 tx_dma_restarts;
++	u64 tx_mac_resets;
++	u64 rx_dma_restarts;
++	u64 rx_dma_timeouts;
++	u64 rx_restarts_dropped;
++
++	struct net_device_stats stats;
++};
++
++/* Function prototypes. */
++static int crisv32_ethernet_init(void);
++static int crisv32_ethernet_device_init(struct net_device *dev);
++static int crisv32_eth_open(struct net_device *dev);
++static int crisv32_eth_close(struct net_device *dev);
++static int crisv32_eth_set_mac_address(struct net_device *dev, void *vpntr);
++static irqreturn_t crisv32rx_eth_interrupt(int irq, void *dev_id);
++static irqreturn_t crisv32tx_eth_interrupt(int irq, void *dev_id);
++static irqreturn_t crisv32nw_eth_interrupt(int irq, void *dev_id);
++static int crisv32_eth_send_packet(struct sk_buff *skb, struct net_device *dev);
++static void crisv32_eth_hw_send_packet(unsigned char *buf, int length,
++				       void *priv);
++static void crisv32_eth_do_tx_recovery(struct net_device *dev);
++static void crisv32_eth_set_rx_mode(struct net_device *dev);
++static int crisv32_eth_ioctl(struct net_device *dev, struct ifreq *ifr,
++			     int cmd);
++static int crisv32_eth_set_config(struct net_device *dev, struct ifmap *map);
++#ifdef CONFIG_CRIS_MACH_ARTPEC3
++static void crisv32_eth_switch_intmem_usage(struct net_device *dev);
++#endif
++static void crisv32_eth_negotiate(struct net_device *dev);
++static void crisv32_eth_set_speed(struct net_device *dev, unsigned long speed);
++#ifndef CONFIG_ETRAX_NO_PHY
++static void crisv32_eth_check_duplex(unsigned long idev);
++static void crisv32_eth_check_speed(unsigned long idev);
++#endif
++
++static void crisv32_eth_set_duplex(struct net_device *dev, enum duplex);
++static int crisv32_eth_probe_transceiver(struct net_device *dev);
++
++static struct ethtool_ops crisv32_ethtool_ops;
++
++#ifndef CONFIG_ETRAX_NO_PHY
++static void generic_check_speed(struct net_device *dev);
++static void generic_check_duplex(struct net_device *dev);
++static void broadcom_check_speed(struct net_device *dev);
++static void broadcom_check_duplex(struct net_device *dev);
++static void tdk_check_speed(struct net_device *dev);
++static void tdk_check_duplex(struct net_device *dev);
++static void intel_check_speed(struct net_device *dev);
++static void intel_check_duplex(struct net_device *dev);
++static void national_check_speed(struct net_device *dev);
++static void national_check_duplex(struct net_device *dev);
++static void vitesse_check_speed(struct net_device *dev);
++static void vitesse_check_duplex(struct net_device *dev);
++static void davicom_check_speed(struct net_device *dev);
++static void davicom_check_duplex(struct net_device *dev);
++#endif
++
++#ifdef CONFIG_NET_POLL_CONTROLLER
++static void crisv32_netpoll(struct net_device *dev);
++#endif
++
++static void crisv32_clear_network_leds(unsigned long dummy);
++static void crisv32_set_network_leds(int active, struct net_device *dev);
++
++static int crisv32_eth_get_mdio_reg(struct net_device *dev,
++				    int phyid, int reg_num);
++static void crisv32_eth_set_mdio_reg(struct net_device *dev,
++				     int phyid, int reg_num, int val);
++static void crisv32_eth_send_mdio_cmd(struct net_device *dev,
++				      unsigned short cmd, int write_cmd);
++static void crisv32_eth_send_mdio_bit(struct net_device *dev,
++				      unsigned char bit);
++static unsigned char crisv32_eth_receive_mdio_bit(struct net_device *dev);
++
++static struct net_device_stats *crisv32_get_stats(struct net_device *dev);
++static void crisv32_start_dma_out(struct crisv32_ethernet_local *np);
++
++#endif /* _ETRAX_ETHERNET_H_ */
+diff -Nur linux-4.4.6.orig/drivers/net/cris/Makefile linux-4.4.6/drivers/net/cris/Makefile
+--- linux-4.4.6.orig/drivers/net/cris/Makefile	2016-03-16 16:43:17.000000000 +0100
++++ linux-4.4.6/drivers/net/cris/Makefile	2016-03-20 11:35:09.089964990 +0100
+@@ -1 +1,2 @@
+ obj-$(CONFIG_ETRAX_ARCH_V10) += eth_v10.o
++obj-$(CONFIG_ETRAX_ARCH_V32) += eth_v32.o

target/linux/patches/4.6.4/crisv32.patch

@@ -0,0 +1,33 @@
+diff -Nur linux-4.4.13.orig/arch/cris/arch-v32/mm/intmem.c linux-4.4.13/arch/cris/arch-v32/mm/intmem.c
+--- linux-4.4.13.orig/arch/cris/arch-v32/mm/intmem.c	2016-06-08 03:14:51.000000000 +0200
++++ linux-4.4.13/arch/cris/arch-v32/mm/intmem.c	2016-06-21 20:40:18.919361891 +0200
+@@ -113,14 +113,14 @@
+ 
+ 			allocation->status = STATUS_FREE;
+ 			/* Join with prev and/or next if also free */
+-			if ((prev != &intmem_allocations) &&
++			if ((&prev->entry != &intmem_allocations) &&
+ 					(prev->status == STATUS_FREE)) {
+ 				prev->size += allocation->size;
+ 				list_del(&allocation->entry);
+ 				kfree(allocation);
+ 				allocation = prev;
+ 			}
+-			if ((next != &intmem_allocations) &&
++			if ((&next->entry != &intmem_allocations) &&
+ 					(next->status == STATUS_FREE)) {
+ 				allocation->size += next->size;
+ 				list_del(&next->entry);
+@@ -145,5 +145,11 @@
+ 		(unsigned long)intmem_virtual + MEM_INTMEM_START +
+ 		RESERVED_SIZE);
+ }
+-device_initcall(crisv32_intmem_init);
+ 
++static int __init crisv32_intmem_setup(void)
++{
++	crisv32_intmem_init();
++
++	return 0;
++}
++device_initcall(crisv32_intmem_setup);