openadk/target/lemote/patches/lemote.patch

diff -Nur linux-2.6.36.orig/arch/mips/Kconfig linux-2.6.36/arch/mips/Kconfig
--- linux-2.6.36.orig/arch/mips/Kconfig	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/Kconfig	2010-11-18 11:47:59.000000000 +0100
@@ -205,7 +205,7 @@
 
 config MACH_LOONGSON
 	bool "Loongson family of machines"
-	select SYS_SUPPORTS_ZBOOT
+	select SYS_SUPPORTS_ZBOOT_UART16550
 	help
 	  This enables the support of Loongson family of machines.
 
@@ -1093,6 +1093,8 @@
 	bool "Loongson 2E"
 	depends on SYS_HAS_CPU_LOONGSON2E
 	select CPU_LOONGSON2
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
 	help
 	  The Loongson 2E processor implements the MIPS III instruction set
 	  with many extensions.
@@ -2012,6 +2014,18 @@
 source "kernel/time/Kconfig"
 
 #
+# High Resolution sched_clock() Configuration
+#
+
+config CPU_HAS_FIXED_C0_COUNT
+	bool
+
+config CPU_SUPPORTS_HR_SCHED_CLOCK
+	bool
+	depends on CPU_HAS_FIXED_C0_COUNT || !CPU_FREQ
+	default y
+
+#
 # Timer Interrupt Frequency Configuration
 #
 
diff -Nur linux-2.6.36.orig/arch/mips/include/asm/dma-mapping.h linux-2.6.36/arch/mips/include/asm/dma-mapping.h
--- linux-2.6.36.orig/arch/mips/include/asm/dma-mapping.h	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/include/asm/dma-mapping.h	2010-11-18 11:47:59.000000000 +0100
@@ -65,4 +65,8 @@
 extern void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
 	       enum dma_data_direction direction);
 
+#define ARCH_HAS_DMA_MMAP_COHERENT
+extern int dma_mmap_coherent(struct device *dev, struct vm_area_struct *vma,
+		void *cpu_addr, dma_addr_t handle, size_t size);
+
 #endif /* _ASM_DMA_MAPPING_H */
diff -Nur linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/cs5536/cs5536.h linux-2.6.36/arch/mips/include/asm/mach-loongson/cs5536/cs5536.h
--- linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/cs5536/cs5536.h	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/include/asm/mach-loongson/cs5536/cs5536.h	2010-11-18 11:47:59.000000000 +0100
@@ -255,21 +255,12 @@
  * IDE STANDARD
  */
 #define	IDE_CAP		0x00
-#define	IDE_CONFIG	0x01
-#define	IDE_SMI		0x02
-#define	IDE_ERROR	0x03
-#define	IDE_PM		0x04
-#define	IDE_DIAG	0x05
-
-/*
- * IDE SPEC.
- */
 #define	IDE_IO_BAR	0x08
 #define	IDE_CFG		0x10
 #define	IDE_DTC		0x12
 #define	IDE_CAST	0x13
 #define	IDE_ETC		0x14
-#define	IDE_INTERNAL_PM	0x15
+#define	IDE_PM		0x15
 
 /*
  * ACC STANDARD
@@ -301,5 +292,40 @@
 /* GPIO : I/O SPACE; REG : 32BITS */
 #define	GPIOL_OUT_VAL		0x00
 #define	GPIOL_OUT_EN		0x04
+#define	GPIOL_OUT_AUX1_SEL	0x10
+/* SMB : I/O SPACE, REG : 8BITS WIDTH */
+#define	SMB_SDA			0x00
+#define	SMB_STS			0x01
+#define	SMB_STS_SLVSTP		(1 << 7)
+#define	SMB_STS_SDAST		(1 << 6)
+#define	SMB_STS_BER		(1 << 5)
+#define	SMB_STS_NEGACK		(1 << 4)
+#define	SMB_STS_STASTR		(1 << 3)
+#define	SMB_STS_NMATCH		(1 << 2)
+#define	SMB_STS_MASTER		(1 << 1)
+#define	SMB_STS_XMIT		(1 << 0)
+#define	SMB_CTRL_STS		0x02
+#define	SMB_CSTS_TGSTL		(1 << 5)
+#define	SMB_CSTS_TSDA		(1 << 4)
+#define	SMB_CSTS_GCMTCH		(1 << 3)
+#define	SMB_CSTS_MATCH		(1 << 2)
+#define	SMB_CSTS_BB		(1 << 1)
+#define	SMB_CSTS_BUSY		(1 << 0)
+#define	SMB_CTRL1		0x03
+#define	SMB_CTRL1_STASTRE	(1 << 7)
+#define	SMB_CTRL1_NMINTE	(1 << 6)
+#define	SMB_CTRL1_GCMEN		(1 << 5)
+#define	SMB_CTRL1_ACK		(1 << 4)
+#define	SMB_CTRL1_RSVD		(1 << 3)
+#define	SMB_CTRL1_INTEN		(1 << 2)
+#define	SMB_CTRL1_STOP		(1 << 1)
+#define	SMB_CTRL1_START		(1 << 0)
+#define	SMB_ADDR		0x04
+#define	SMB_ADDR_SAEN		(1 << 7)
+#define	SMB_CONTROLLER_ADDR	(0xef << 0)
+#define	SMB_CTRL2		0x05
+#define	SMB_FREQ		(0x20 << 1)
+#define	SMB_ENABLE		(0x01 << 0)
+#define	SMB_CTRL3		0x06
 
 #endif				/* _CS5536_H */
diff -Nur linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h linux-2.6.36/arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h
--- linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/include/asm/mach-loongson/cs5536/cs5536_mfgpt.h	2010-11-18 11:47:59.000000000 +0100
@@ -32,4 +32,9 @@
 #define MFGPT0_CNT	(MFGPT_BASE + 4)
 #define MFGPT0_SETUP	(MFGPT_BASE + 6)
 
+#define MFGPT2_CMP1	(MFGPT_BASE + 0x10)
+#define MFGPT2_CMP2	(MFGPT_BASE + 0x12)
+#define MFGPT2_CNT	(MFGPT_BASE + 0x14)
+#define MFGPT2_SETUP	(MFGPT_BASE + 0x16)
+
 #endif /*!_CS5536_MFGPT_H */
diff -Nur linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/ec_kb3310b.h linux-2.6.36/arch/mips/include/asm/mach-loongson/ec_kb3310b.h
--- linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/ec_kb3310b.h	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/arch/mips/include/asm/mach-loongson/ec_kb3310b.h	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,191 @@
+/*
+ * KB3310B Embedded Controller
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-03-14
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _EC_KB3310B_H
+#define _EC_KB3310B_H
+
+extern unsigned char ec_read(unsigned short addr);
+extern void ec_write(unsigned short addr, unsigned char val);
+extern int ec_query_seq(unsigned char cmd);
+extern int ec_query_event_num(void);
+extern int ec_get_event_num(void);
+
+typedef int (*sci_handler) (int status);
+extern sci_handler yeeloong_report_lid_status;
+
+#define SCI_IRQ_NUM 0x0A
+
+/*
+ * The following registers are determined by the EC index configuration.
+ * 1, fill the PORT_HIGH as EC register high part.
+ * 2, fill the PORT_LOW as EC register low part.
+ * 3, fill the PORT_DATA as EC register write data or get the data from it.
+ */
+#define	EC_IO_PORT_HIGH	0x0381
+#define	EC_IO_PORT_LOW	0x0382
+#define	EC_IO_PORT_DATA	0x0383
+
+/*
+ * EC delay time is 500us for register and status access
+ */
+#define	EC_REG_DELAY	500	/* unit : us */
+#define	EC_CMD_TIMEOUT	0x1000
+
+/*
+ * EC access port for SCI communication
+ */
+#define	EC_CMD_PORT		0x66
+#define	EC_STS_PORT		0x66
+#define	EC_DAT_PORT		0x62
+#define	CMD_INIT_IDLE_MODE	0xdd
+#define	CMD_EXIT_IDLE_MODE	0xdf
+#define	CMD_INIT_RESET_MODE	0xd8
+#define	CMD_REBOOT_SYSTEM	0x8c
+#define	CMD_GET_EVENT_NUM	0x84
+#define	CMD_PROGRAM_PIECE	0xda
+
+/* Temperature & Fan registers */
+#define	REG_TEMPERATURE_VALUE	0xF458
+#define	REG_FAN_AUTO_MAN_SWITCH 0xF459
+#define	BIT_FAN_AUTO		0
+#define	BIT_FAN_MANUAL		1
+#define	REG_FAN_CONTROL		0xF4D2
+#define	BIT_FAN_CONTROL_ON	(1 << 0)
+#define	BIT_FAN_CONTROL_OFF	(0 << 0)
+#define	REG_FAN_STATUS		0xF4DA
+#define	BIT_FAN_STATUS_ON	(1 << 0)
+#define	BIT_FAN_STATUS_OFF	(0 << 0)
+#define	REG_FAN_SPEED_HIGH	0xFE22
+#define	REG_FAN_SPEED_LOW	0xFE23
+#define	REG_FAN_SPEED_LEVEL	0xF4CC
+/* Fan speed divider */
+#define	FAN_SPEED_DIVIDER	480000	/* (60*1000*1000/62.5/2)*/
+
+/* Battery registers */
+#define	REG_BAT_DESIGN_CAP_HIGH		0xF77D
+#define	REG_BAT_DESIGN_CAP_LOW		0xF77E
+#define	REG_BAT_FULLCHG_CAP_HIGH	0xF780
+#define	REG_BAT_FULLCHG_CAP_LOW		0xF781
+#define	REG_BAT_DESIGN_VOL_HIGH		0xF782
+#define	REG_BAT_DESIGN_VOL_LOW		0xF783
+#define	REG_BAT_CURRENT_HIGH		0xF784
+#define	REG_BAT_CURRENT_LOW		0xF785
+#define	REG_BAT_VOLTAGE_HIGH		0xF786
+#define	REG_BAT_VOLTAGE_LOW		0xF787
+#define	REG_BAT_TEMPERATURE_HIGH	0xF788
+#define	REG_BAT_TEMPERATURE_LOW		0xF789
+#define	REG_BAT_RELATIVE_CAP_HIGH	0xF492
+#define	REG_BAT_RELATIVE_CAP_LOW	0xF493
+#define	REG_BAT_VENDOR			0xF4C4
+#define	FLAG_BAT_VENDOR_SANYO		0x01
+#define	FLAG_BAT_VENDOR_SIMPLO		0x02
+#define	REG_BAT_CELL_COUNT		0xF4C6
+#define	FLAG_BAT_CELL_3S1P		0x03
+#define	FLAG_BAT_CELL_3S2P		0x06
+#define	REG_BAT_CHARGE			0xF4A2
+#define	FLAG_BAT_CHARGE_DISCHARGE	0x01
+#define	FLAG_BAT_CHARGE_CHARGE		0x02
+#define	FLAG_BAT_CHARGE_ACPOWER		0x00
+#define	REG_BAT_STATUS			0xF4B0
+#define	BIT_BAT_STATUS_LOW		(1 << 5)
+#define	BIT_BAT_STATUS_DESTROY		(1 << 2)
+#define	BIT_BAT_STATUS_FULL		(1 << 1)
+#define	BIT_BAT_STATUS_IN		(1 << 0)
+#define	REG_BAT_CHARGE_STATUS		0xF4B1
+#define	BIT_BAT_CHARGE_STATUS_OVERTEMP	(1 << 2)
+#define	BIT_BAT_CHARGE_STATUS_PRECHG	(1 << 1)
+#define	REG_BAT_STATE			0xF482
+#define	BIT_BAT_STATE_CHARGING		(1 << 1)
+#define	BIT_BAT_STATE_DISCHARGING	(1 << 0)
+#define	REG_BAT_POWER			0xF440
+#define	BIT_BAT_POWER_S3		(1 << 2)
+#define	BIT_BAT_POWER_ON		(1 << 1)
+#define	BIT_BAT_POWER_ACIN		(1 << 0)
+
+/* Audio: rd/wr */
+#define	REG_AUDIO_VOLUME	0xF46C
+#define	REG_AUDIO_MUTE		0xF4E7
+#define	REG_AUDIO_BEEP		0xF4D0
+/* USB port power or not: rd/wr */
+#define	REG_USB0_FLAG		0xF461
+#define	REG_USB1_FLAG		0xF462
+#define	REG_USB2_FLAG		0xF463
+#define	BIT_USB_FLAG_ON		1
+#define	BIT_USB_FLAG_OFF	0
+/* LID */
+#define	REG_LID_DETECT		0xF4BD
+#define	BIT_LID_DETECT_ON	1
+#define	BIT_LID_DETECT_OFF	0
+/* CRT */
+#define	REG_CRT_DETECT		0xF4AD
+#define	BIT_CRT_DETECT_PLUG	1
+#define	BIT_CRT_DETECT_UNPLUG	0
+/* LCD backlight brightness adjust: 9 levels */
+#define	REG_DISPLAY_BRIGHTNESS	0xF4F5
+/* Black screen Status */
+#define	BIT_DISPLAY_LCD_ON	1
+#define	BIT_DISPLAY_LCD_OFF	0
+/* LCD backlight control: off/restore */
+#define	REG_BACKLIGHT_CTRL	0xF7BD
+#define	BIT_BACKLIGHT_ON	1
+#define	BIT_BACKLIGHT_OFF	0
+/* Reset the machine auto-clear: rd/wr */
+#define	REG_RESET		0xF4EC
+#define	BIT_RESET_ON		1
+/* Light the led: rd/wr */
+#define	REG_LED			0xF4C8
+#define	BIT_LED_RED_POWER	(1 << 0)
+#define	BIT_LED_ORANGE_POWER	(1 << 1)
+#define	BIT_LED_GREEN_CHARGE	(1 << 2)
+#define	BIT_LED_RED_CHARGE	(1 << 3)
+#define	BIT_LED_NUMLOCK		(1 << 4)
+/* Test led mode, all led on/off */
+#define	REG_LED_TEST		0xF4C2
+#define	BIT_LED_TEST_IN		1
+#define	BIT_LED_TEST_OUT	0
+/* Camera on/off */
+#define	REG_CAMERA_STATUS	0xF46A
+#define	BIT_CAMERA_STATUS_ON	1
+#define	BIT_CAMERA_STATUS_OFF	0
+#define	REG_CAMERA_CONTROL	0xF7B7
+#define	BIT_CAMERA_CONTROL_OFF	0
+#define	BIT_CAMERA_CONTROL_ON	1
+/* Wlan Status */
+#define	REG_WLAN		0xF4FA
+#define	BIT_WLAN_ON		1
+#define	BIT_WLAN_OFF		0
+#define	REG_DISPLAY_LCD		0xF79F
+
+/* SCI Event Number from EC */
+enum {
+	EVENT_LID = 0x23,	/*  Turn on/off LID */
+	EVENT_SWITCHVIDEOMODE,	/*  Fn+F3 for display switch */
+	EVENT_SLEEP,		/*  Fn+F1 for entering sleep mode */
+	EVENT_OVERTEMP,		/*  Over-temperature happened */
+	EVENT_CRT_DETECT,	/*  CRT is connected */
+	EVENT_CAMERA,		/*  Camera on/off */
+	EVENT_USB_OC2,		/*  USB2 Over Current occurred */
+	EVENT_USB_OC0,		/*  USB0 Over Current occurred */
+	EVENT_DISPLAYTOGGLE,	/*  Fn+F2, Turn on/off backlight */
+	EVENT_AUDIO_MUTE,	/*  Fn+F4, Mute on/off */
+	EVENT_DISPLAY_BRIGHTNESS,/* Fn+^/V, LCD backlight brightness adjust */
+	EVENT_AC_BAT,		/*  AC & Battery relative issue */
+	EVENT_AUDIO_VOLUME,	/*  Fn+<|>, Volume adjust */
+	EVENT_WLAN,		/*  Wlan on/off */
+};
+
+#define EVENT_START	EVENT_LID
+#define EVENT_END	EVENT_WLAN
+
+#endif /* !_EC_KB3310B_H */
diff -Nur linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/loongson.h linux-2.6.36/arch/mips/include/asm/mach-loongson/loongson.h
--- linux-2.6.36.orig/arch/mips/include/asm/mach-loongson/loongson.h	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/include/asm/mach-loongson/loongson.h	2010-11-18 11:47:59.000000000 +0100
@@ -42,6 +42,12 @@
 #endif
 }
 
+/*
+ * Copy kernel command line from arcs_cmdline
+ */
+#include <asm/setup.h>
+extern char loongson_cmdline[COMMAND_LINE_SIZE];
+
 /* irq operation functions */
 extern void bonito_irqdispatch(void);
 extern void __init bonito_irq_init(void);
diff -Nur linux-2.6.36.orig/arch/mips/kernel/csrc-r4k.c linux-2.6.36/arch/mips/kernel/csrc-r4k.c
--- linux-2.6.36.orig/arch/mips/kernel/csrc-r4k.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/kernel/csrc-r4k.c	2010-11-18 11:47:59.000000000 +0100
@@ -6,10 +6,66 @@
  * Copyright (C) 2007 by Ralf Baechle
  */
 #include <linux/clocksource.h>
+#include <linux/cnt32_to_63.h>
 #include <linux/init.h>
+#include <linux/timer.h>
 
 #include <asm/time.h>
 
+#ifdef CONFIG_CPU_SUPPORTS_HR_SCHED_CLOCK
+/*
+ * MIPS sched_clock implementation.
+ *
+ * Because the hardware timer period is quite short and because cnt32_to_63()
+ * needs to be called at least once per half period to work properly, a kernel
+ * timer is set up to ensure this requirement is always met.
+ *
+ * Please refer to include/linux/cnt32_to_63.h and arch/arm/plat-orion/time.c
+ */
+#define CLOCK2NS_SCALE_FACTOR 8
+
+static unsigned long clock2ns_scale __read_mostly;
+
+unsigned long long notrace sched_clock(void)
+{
+	unsigned long long v = cnt32_to_63(read_c0_count());
+	return (v * clock2ns_scale) >> CLOCK2NS_SCALE_FACTOR;
+}
+
+static struct timer_list cnt32_to_63_keepwarm_timer;
+
+static void cnt32_to_63_keepwarm(unsigned long data)
+{
+	mod_timer(&cnt32_to_63_keepwarm_timer, round_jiffies(jiffies + data));
+	sched_clock();
+}
+#endif
+
+static inline void setup_hres_sched_clock(unsigned long clock)
+{
+#ifdef CONFIG_CPU_SUPPORTS_HR_SCHED_CLOCK
+	unsigned long long v;
+	unsigned long data;
+
+	v = NSEC_PER_SEC;
+	v <<= CLOCK2NS_SCALE_FACTOR;
+	v += clock/2;
+	do_div(v, clock);
+	/*
+	 * We want an even value to automatically clear the top bit
+	 * returned by cnt32_to_63() without an additional run time
+	 * instruction. So if the LSB is 1 then round it up.
+	 */
+	if (v & 1)
+		v++;
+	clock2ns_scale = v;
+
+	data = 0x80000000UL / clock * HZ;
+	setup_timer(&cnt32_to_63_keepwarm_timer, cnt32_to_63_keepwarm, data);
+	mod_timer(&cnt32_to_63_keepwarm_timer, round_jiffies(jiffies + data));
+#endif
+}
+
 static cycle_t c0_hpt_read(struct clocksource *cs)
 {
 	return read_c0_count();
@@ -27,6 +83,8 @@
 	if (!cpu_has_counter || !mips_hpt_frequency)
 		return -ENXIO;
 
+	setup_hres_sched_clock(mips_hpt_frequency);
+
 	/* Calculate a somewhat reasonable rating value */
 	clocksource_mips.rating = 200 + mips_hpt_frequency / 10000000;
 
diff -Nur linux-2.6.36.orig/arch/mips/kernel/time.c linux-2.6.36/arch/mips/kernel/time.c
--- linux-2.6.36.orig/arch/mips/kernel/time.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/kernel/time.c	2010-11-18 11:47:59.000000000 +0100
@@ -119,6 +119,11 @@
 
 void __init time_init(void)
 {
+#ifdef CONFIG_HR_SCHED_CLOCK
+	if (!mips_clockevent_init() || !cpu_has_mfc0_count_bug())
+		write_c0_count(0);
+#endif
+
 	plat_time_init();
 
 	if (!mips_clockevent_init() || !cpu_has_mfc0_count_bug())
diff -Nur linux-2.6.36.orig/arch/mips/loongson/common/cmdline.c linux-2.6.36/arch/mips/loongson/common/cmdline.c
--- linux-2.6.36.orig/arch/mips/loongson/common/cmdline.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/common/cmdline.c	2010-11-18 11:47:59.000000000 +0100
@@ -17,10 +17,15 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
+#include <linux/module.h>
 #include <asm/bootinfo.h>
 
 #include <loongson.h>
 
+/* the kernel command line copied from arcs_cmdline */
+char loongson_cmdline[COMMAND_LINE_SIZE];
+EXPORT_SYMBOL(loongson_cmdline);
+
 void __init prom_init_cmdline(void)
 {
 	int prom_argc;
@@ -50,4 +55,26 @@
 		strcat(arcs_cmdline, " root=/dev/hda1");
 
 	prom_init_machtype();
+
+	/* append machine specific command line */
+	switch (mips_machtype) {
+	case MACH_LEMOTE_LL2F:
+		if ((strstr(arcs_cmdline, "video=")) == NULL)
+			strcat(arcs_cmdline, " video=sisfb:1360x768-16@60");
+		break;
+	case MACH_LEMOTE_FL2F:
+		if ((strstr(arcs_cmdline, "ide_core.ignore_cable=")) == NULL)
+			strcat(arcs_cmdline, " ide_core.ignore_cable=0");
+		break;
+	case MACH_LEMOTE_ML2F7:
+		/* Mengloong-2F has a 800x480 screen */
+		if ((strstr(arcs_cmdline, "vga=")) == NULL)
+			strcat(arcs_cmdline, " vga=0x313");
+		break;
+	default:
+		break;
+	}
+
+	/* copy arcs_cmdline into loongson_cmdline */
+	strncpy(loongson_cmdline, arcs_cmdline, COMMAND_LINE_SIZE);
 }
diff -Nur linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_acc.c linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_acc.c
--- linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_acc.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_acc.c	2010-11-18 11:47:59.000000000 +0100
@@ -18,7 +18,7 @@
 
 void pci_acc_write_reg(int reg, u32 value)
 {
-	u32 hi = 0, lo = value;
+	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_COMMAND:
@@ -66,75 +66,73 @@
 u32 pci_acc_read_reg(int reg)
 {
 	u32 hi, lo;
-	u32 conf_data = 0;
+	u32 cfg = 0;
 
 	switch (reg) {
 	case PCI_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_ACC_DEVICE_ID, CS5536_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_ACC_DEVICE_ID,
+				CS5536_VENDOR_ID);
 		break;
 	case PCI_COMMAND:
 		_rdmsr(GLIU_MSR_REG(GLIU_IOD_BM1), &hi, &lo);
 		if (((lo & 0xfff00000) || (hi & 0x000000ff))
 		    && ((hi & 0xf0000000) == 0xa0000000))
-			conf_data |= PCI_COMMAND_IO;
+			cfg |= PCI_COMMAND_IO;
 		_rdmsr(GLIU_MSR_REG(GLIU_PAE), &hi, &lo);
 		if ((lo & 0x300) == 0x300)
-			conf_data |= PCI_COMMAND_MASTER;
+			cfg |= PCI_COMMAND_MASTER;
 		break;
 	case PCI_STATUS:
-		conf_data |= PCI_STATUS_66MHZ;
-		conf_data |= PCI_STATUS_FAST_BACK;
+		cfg |= PCI_STATUS_66MHZ;
+		cfg |= PCI_STATUS_FAST_BACK;
 		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
 		if (lo & SB_PARE_ERR_FLAG)
-			conf_data |= PCI_STATUS_PARITY;
-		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+			cfg |= PCI_STATUS_PARITY;
+		cfg |= PCI_STATUS_DEVSEL_MEDIUM;
 		break;
 	case PCI_CLASS_REVISION:
 		_rdmsr(ACC_MSR_REG(ACC_CAP), &hi, &lo);
-		conf_data = lo & 0x000000ff;
-		conf_data |= (CS5536_ACC_CLASS_CODE << 8);
+		cfg = lo & 0x000000ff;
+		cfg |= (CS5536_ACC_CLASS_CODE << 8);
 		break;
 	case PCI_CACHE_LINE_SIZE:
-		conf_data =
-		    CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
-					    PCI_NORMAL_LATENCY_TIMER);
+		cfg = CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
+				PCI_NORMAL_LATENCY_TIMER);
 		break;
 	case PCI_BAR0_REG:
 		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
 		if (lo & SOFT_BAR_ACC_FLAG) {
-			conf_data = CS5536_ACC_RANGE |
+			cfg = CS5536_ACC_RANGE |
 			    PCI_BASE_ADDRESS_SPACE_IO;
 			lo &= ~SOFT_BAR_ACC_FLAG;
 			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
 		} else {
 			_rdmsr(GLIU_MSR_REG(GLIU_IOD_BM1), &hi, &lo);
-			conf_data = (hi & 0x000000ff) << 12;
-			conf_data |= (lo & 0xfff00000) >> 20;
-			conf_data |= 0x01;
-			conf_data &= ~0x02;
+			cfg = (hi & 0x000000ff) << 12;
+			cfg |= (lo & 0xfff00000) >> 20;
+			cfg |= 0x01;
+			cfg &= ~0x02;
 		}
 		break;
 	case PCI_CARDBUS_CIS:
-		conf_data = PCI_CARDBUS_CIS_POINTER;
+		cfg = PCI_CARDBUS_CIS_POINTER;
 		break;
 	case PCI_SUBSYSTEM_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_ACC_SUB_ID, CS5536_SUB_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_ACC_SUB_ID,
+				CS5536_SUB_VENDOR_ID);
 		break;
 	case PCI_ROM_ADDRESS:
-		conf_data = PCI_EXPANSION_ROM_BAR;
+		cfg = PCI_EXPANSION_ROM_BAR;
 		break;
 	case PCI_CAPABILITY_LIST:
-		conf_data = PCI_CAPLIST_USB_POINTER;
+		cfg = PCI_CAPLIST_USB_POINTER;
 		break;
 	case PCI_INTERRUPT_LINE:
-		conf_data =
-		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_ACC_INTR);
+		cfg = CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_ACC_INTR);
 		break;
 	default:
 		break;
 	}
 
-	return conf_data;
+	return cfg;
 }
diff -Nur linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_ehci.c linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_ehci.c
--- linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_ehci.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_ehci.c	2010-11-18 11:47:59.000000000 +0100
@@ -18,7 +18,7 @@
 
 void pci_ehci_write_reg(int reg, u32 value)
 {
-	u32 hi = 0, lo = value;
+	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_COMMAND:
@@ -78,83 +78,81 @@
 
 u32 pci_ehci_read_reg(int reg)
 {
-	u32 conf_data = 0;
+	u32 cfg = 0;
 	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_EHCI_DEVICE_ID, CS5536_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_EHCI_DEVICE_ID,
+				CS5536_VENDOR_ID);
 		break;
 	case PCI_COMMAND:
 		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
 		if (hi & PCI_COMMAND_MASTER)
-			conf_data |= PCI_COMMAND_MASTER;
+			cfg |= PCI_COMMAND_MASTER;
 		if (hi & PCI_COMMAND_MEMORY)
-			conf_data |= PCI_COMMAND_MEMORY;
+			cfg |= PCI_COMMAND_MEMORY;
 		break;
 	case PCI_STATUS:
-		conf_data |= PCI_STATUS_66MHZ;
-		conf_data |= PCI_STATUS_FAST_BACK;
+		cfg |= PCI_STATUS_66MHZ;
+		cfg |= PCI_STATUS_FAST_BACK;
 		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
 		if (lo & SB_PARE_ERR_FLAG)
-			conf_data |= PCI_STATUS_PARITY;
-		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+			cfg |= PCI_STATUS_PARITY;
+		cfg |= PCI_STATUS_DEVSEL_MEDIUM;
 		break;
 	case PCI_CLASS_REVISION:
 		_rdmsr(USB_MSR_REG(USB_CAP), &hi, &lo);
-		conf_data = lo & 0x000000ff;
-		conf_data |= (CS5536_EHCI_CLASS_CODE << 8);
+		cfg = lo & 0x000000ff;
+		cfg |= (CS5536_EHCI_CLASS_CODE << 8);
 		break;
 	case PCI_CACHE_LINE_SIZE:
-		conf_data =
-		    CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
-					    PCI_NORMAL_LATENCY_TIMER);
+		cfg = CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
+				PCI_NORMAL_LATENCY_TIMER);
 		break;
 	case PCI_BAR0_REG:
 		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
 		if (lo & SOFT_BAR_EHCI_FLAG) {
-			conf_data = CS5536_EHCI_RANGE |
+			cfg = CS5536_EHCI_RANGE |
 			    PCI_BASE_ADDRESS_SPACE_MEMORY;
 			lo &= ~SOFT_BAR_EHCI_FLAG;
 			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
 		} else {
 			_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
-			conf_data = lo & 0xfffff000;
+			cfg = lo & 0xfffff000;
 		}
 		break;
 	case PCI_CARDBUS_CIS:
-		conf_data = PCI_CARDBUS_CIS_POINTER;
+		cfg = PCI_CARDBUS_CIS_POINTER;
 		break;
 	case PCI_SUBSYSTEM_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_EHCI_SUB_ID, CS5536_SUB_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_EHCI_SUB_ID,
+				CS5536_SUB_VENDOR_ID);
 		break;
 	case PCI_ROM_ADDRESS:
-		conf_data = PCI_EXPANSION_ROM_BAR;
+		cfg = PCI_EXPANSION_ROM_BAR;
 		break;
 	case PCI_CAPABILITY_LIST:
-		conf_data = PCI_CAPLIST_USB_POINTER;
+		cfg = PCI_CAPLIST_USB_POINTER;
 		break;
 	case PCI_INTERRUPT_LINE:
-		conf_data =
-		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_USB_INTR);
+		cfg = CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_USB_INTR);
 		break;
 	case PCI_EHCI_LEGSMIEN_REG:
 		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
-		conf_data = (hi & 0x003f0000) >> 16;
+		cfg = (hi & 0x003f0000) >> 16;
 		break;
 	case PCI_EHCI_LEGSMISTS_REG:
 		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
-		conf_data = (hi & 0x3f000000) >> 24;
+		cfg = (hi & 0x3f000000) >> 24;
 		break;
 	case PCI_EHCI_FLADJ_REG:
 		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
-		conf_data = hi & 0x00003f00;
+		cfg = hi & 0x00003f00;
 		break;
 	default:
 		break;
 	}
 
-	return conf_data;
+	return cfg;
 }
diff -Nur linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_ide.c linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_ide.c
--- linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_ide.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_ide.c	2010-11-18 11:47:59.000000000 +0100
@@ -18,7 +18,7 @@
 
 void pci_ide_write_reg(int reg, u32 value)
 {
-	u32 hi = 0, lo = value;
+	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_COMMAND:
@@ -72,26 +72,16 @@
 			_wrmsr(IDE_MSR_REG(IDE_CFG), hi, lo);
 		}
 		break;
-	case PCI_IDE_DTC_REG:
-		_rdmsr(IDE_MSR_REG(IDE_DTC), &hi, &lo);
-		lo = value;
-		_wrmsr(IDE_MSR_REG(IDE_DTC), hi, lo);
-		break;
-	case PCI_IDE_CAST_REG:
-		_rdmsr(IDE_MSR_REG(IDE_CAST), &hi, &lo);
-		lo = value;
-		_wrmsr(IDE_MSR_REG(IDE_CAST), hi, lo);
-		break;
-	case PCI_IDE_ETC_REG:
-		_rdmsr(IDE_MSR_REG(IDE_ETC), &hi, &lo);
-		lo = value;
-		_wrmsr(IDE_MSR_REG(IDE_ETC), hi, lo);
-		break;
-	case PCI_IDE_PM_REG:
-		_rdmsr(IDE_MSR_REG(IDE_INTERNAL_PM), &hi, &lo);
-		lo = value;
-		_wrmsr(IDE_MSR_REG(IDE_INTERNAL_PM), hi, lo);
-		break;
+#define SET_PCI_IDE_REG(r)				\
+	case PCI_IDE_##r##_REG:				\
+		_rdmsr(IDE_MSR_REG(IDE_##r), &hi, &lo); \
+		lo = value;				\
+		_wrmsr(IDE_MSR_REG(IDE_##r), hi, lo);	\
+		break;
+	SET_PCI_IDE_REG(DTC)
+	SET_PCI_IDE_REG(CAST)
+	SET_PCI_IDE_REG(ETC)
+	SET_PCI_IDE_REG(PM)
 	default:
 		break;
 	}
@@ -99,94 +89,82 @@
 
 u32 pci_ide_read_reg(int reg)
 {
-	u32 conf_data = 0;
+	u32 cfg = 0;
 	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_IDE_DEVICE_ID, CS5536_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_IDE_DEVICE_ID,
+				CS5536_VENDOR_ID);
 		break;
 	case PCI_COMMAND:
 		_rdmsr(IDE_MSR_REG(IDE_IO_BAR), &hi, &lo);
 		if (lo & 0xfffffff0)
-			conf_data |= PCI_COMMAND_IO;
+			cfg |= PCI_COMMAND_IO;
 		_rdmsr(GLIU_MSR_REG(GLIU_PAE), &hi, &lo);
 		if ((lo & 0x30) == 0x30)
-			conf_data |= PCI_COMMAND_MASTER;
+			cfg |= PCI_COMMAND_MASTER;
 		break;
 	case PCI_STATUS:
-		conf_data |= PCI_STATUS_66MHZ;
-		conf_data |= PCI_STATUS_FAST_BACK;
+		cfg |= PCI_STATUS_66MHZ;
+		cfg |= PCI_STATUS_FAST_BACK;
 		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
 		if (lo & SB_PARE_ERR_FLAG)
-			conf_data |= PCI_STATUS_PARITY;
-		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+			cfg |= PCI_STATUS_PARITY;
+		cfg |= PCI_STATUS_DEVSEL_MEDIUM;
 		break;
 	case PCI_CLASS_REVISION:
 		_rdmsr(IDE_MSR_REG(IDE_CAP), &hi, &lo);
-		conf_data = lo & 0x000000ff;
-		conf_data |= (CS5536_IDE_CLASS_CODE << 8);
+		cfg = lo & 0x000000ff;
+		cfg |= (CS5536_IDE_CLASS_CODE << 8);
 		break;
 	case PCI_CACHE_LINE_SIZE:
 		_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
 		hi &= 0x000000f8;
-		conf_data = CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE, hi);
+		cfg = CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE, hi);
 		break;
 	case PCI_BAR4_REG:
 		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
 		if (lo & SOFT_BAR_IDE_FLAG) {
-			conf_data = CS5536_IDE_RANGE |
+			cfg = CS5536_IDE_RANGE |
 			    PCI_BASE_ADDRESS_SPACE_IO;
 			lo &= ~SOFT_BAR_IDE_FLAG;
 			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
 		} else {
 			_rdmsr(IDE_MSR_REG(IDE_IO_BAR), &hi, &lo);
-			conf_data = lo & 0xfffffff0;
-			conf_data |= 0x01;
-			conf_data &= ~0x02;
+			cfg = lo & 0xfffffff0;
+			cfg |= 0x01;
+			cfg &= ~0x02;
 		}
 		break;
 	case PCI_CARDBUS_CIS:
-		conf_data = PCI_CARDBUS_CIS_POINTER;
+		cfg = PCI_CARDBUS_CIS_POINTER;
 		break;
 	case PCI_SUBSYSTEM_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_IDE_SUB_ID, CS5536_SUB_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_IDE_SUB_ID,
+				CS5536_SUB_VENDOR_ID);
 		break;
 	case PCI_ROM_ADDRESS:
-		conf_data = PCI_EXPANSION_ROM_BAR;
+		cfg = PCI_EXPANSION_ROM_BAR;
 		break;
 	case PCI_CAPABILITY_LIST:
-		conf_data = PCI_CAPLIST_POINTER;
+		cfg = PCI_CAPLIST_POINTER;
 		break;
 	case PCI_INTERRUPT_LINE:
-		conf_data =
-		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_IDE_INTR);
-		break;
-	case PCI_IDE_CFG_REG:
-		_rdmsr(IDE_MSR_REG(IDE_CFG), &hi, &lo);
-		conf_data = lo;
-		break;
-	case PCI_IDE_DTC_REG:
-		_rdmsr(IDE_MSR_REG(IDE_DTC), &hi, &lo);
-		conf_data = lo;
-		break;
-	case PCI_IDE_CAST_REG:
-		_rdmsr(IDE_MSR_REG(IDE_CAST), &hi, &lo);
-		conf_data = lo;
-		break;
-	case PCI_IDE_ETC_REG:
-		_rdmsr(IDE_MSR_REG(IDE_ETC), &hi, &lo);
-		conf_data = lo;
-		break;
-	case PCI_IDE_PM_REG:
-		_rdmsr(IDE_MSR_REG(IDE_INTERNAL_PM), &hi, &lo);
-		conf_data = lo;
+		cfg = CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_IDE_INTR);
 		break;
+#define GET_PCI_IDE_REG(r)					\
+	case PCI_IDE_##r##_REG:					\
+		_rdmsr(IDE_MSR_REG(IDE_##r), &hi, &cfg);	\
+		break;
+	GET_PCI_IDE_REG(CFG)
+	GET_PCI_IDE_REG(DTC)
+	GET_PCI_IDE_REG(CAST)
+	GET_PCI_IDE_REG(ETC)
+	GET_PCI_IDE_REG(PM)
 	default:
 		break;
 	}
 
-	return conf_data;
+	return cfg;
 }
diff -Nur linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_ohci.c linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_ohci.c
--- linux-2.6.36.orig/arch/mips/loongson/common/cs5536/cs5536_ohci.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/common/cs5536/cs5536_ohci.c	2010-11-18 11:47:59.000000000 +0100
@@ -18,7 +18,7 @@
 
 void pci_ohci_write_reg(int reg, u32 value)
 {
-	u32 hi = 0, lo = value;
+	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_COMMAND:
@@ -73,77 +73,75 @@
 
 u32 pci_ohci_read_reg(int reg)
 {
-	u32 conf_data = 0;
+	u32 cfg = 0;
 	u32 hi, lo;
 
 	switch (reg) {
 	case PCI_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_OHCI_DEVICE_ID, CS5536_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_OHCI_DEVICE_ID,
+				CS5536_VENDOR_ID);
 		break;
 	case PCI_COMMAND:
 		_rdmsr(USB_MSR_REG(USB_OHCI), &hi, &lo);
 		if (hi & PCI_COMMAND_MASTER)
-			conf_data |= PCI_COMMAND_MASTER;
+			cfg |= PCI_COMMAND_MASTER;
 		if (hi & PCI_COMMAND_MEMORY)
-			conf_data |= PCI_COMMAND_MEMORY;
+			cfg |= PCI_COMMAND_MEMORY;
 		break;
 	case PCI_STATUS:
-		conf_data |= PCI_STATUS_66MHZ;
-		conf_data |= PCI_STATUS_FAST_BACK;
+		cfg |= PCI_STATUS_66MHZ;
+		cfg |= PCI_STATUS_FAST_BACK;
 		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
 		if (lo & SB_PARE_ERR_FLAG)
-			conf_data |= PCI_STATUS_PARITY;
-		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+			cfg |= PCI_STATUS_PARITY;
+		cfg |= PCI_STATUS_DEVSEL_MEDIUM;
 		break;
 	case PCI_CLASS_REVISION:
 		_rdmsr(USB_MSR_REG(USB_CAP), &hi, &lo);
-		conf_data = lo & 0x000000ff;
-		conf_data |= (CS5536_OHCI_CLASS_CODE << 8);
+		cfg = lo & 0x000000ff;
+		cfg |= (CS5536_OHCI_CLASS_CODE << 8);
 		break;
 	case PCI_CACHE_LINE_SIZE:
-		conf_data =
-		    CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
-					    PCI_NORMAL_LATENCY_TIMER);
+		cfg = CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
+				PCI_NORMAL_LATENCY_TIMER);
 		break;
 	case PCI_BAR0_REG:
 		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
 		if (lo & SOFT_BAR_OHCI_FLAG) {
-			conf_data = CS5536_OHCI_RANGE |
+			cfg = CS5536_OHCI_RANGE |
 			    PCI_BASE_ADDRESS_SPACE_MEMORY;
 			lo &= ~SOFT_BAR_OHCI_FLAG;
 			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
 		} else {
 			_rdmsr(USB_MSR_REG(USB_OHCI), &hi, &lo);
-			conf_data = lo & 0xffffff00;
-			conf_data &= ~0x0000000f;	/* 32bit mem */
+			cfg = lo & 0xffffff00;
+			cfg &= ~0x0000000f;	/* 32bit mem */
 		}
 		break;
 	case PCI_CARDBUS_CIS:
-		conf_data = PCI_CARDBUS_CIS_POINTER;
+		cfg = PCI_CARDBUS_CIS_POINTER;
 		break;
 	case PCI_SUBSYSTEM_VENDOR_ID:
-		conf_data =
-		    CFG_PCI_VENDOR_ID(CS5536_OHCI_SUB_ID, CS5536_SUB_VENDOR_ID);
+		cfg = CFG_PCI_VENDOR_ID(CS5536_OHCI_SUB_ID,
+				CS5536_SUB_VENDOR_ID);
 		break;
 	case PCI_ROM_ADDRESS:
-		conf_data = PCI_EXPANSION_ROM_BAR;
+		cfg = PCI_EXPANSION_ROM_BAR;
 		break;
 	case PCI_CAPABILITY_LIST:
-		conf_data = PCI_CAPLIST_USB_POINTER;
+		cfg = PCI_CAPLIST_USB_POINTER;
 		break;
 	case PCI_INTERRUPT_LINE:
-		conf_data =
-		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_USB_INTR);
+		cfg = CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_USB_INTR);
 		break;
 	case PCI_OHCI_INT_REG:
 		_rdmsr(DIVIL_MSR_REG(PIC_YSEL_LOW), &hi, &lo);
 		if ((lo & 0x00000f00) == CS5536_USB_INTR)
-			conf_data = 1;
+			cfg = 1;
 		break;
 	default:
 		break;
 	}
 
-	return conf_data;
+	return cfg;
 }
diff -Nur linux-2.6.36.orig/arch/mips/loongson/common/mtd.c linux-2.6.36/arch/mips/loongson/common/mtd.c
--- linux-2.6.36.orig/arch/mips/loongson/common/mtd.c	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/arch/mips/loongson/common/mtd.c	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,91 @@
+/*
+ *  Driver for flushing/dumping ROM of PMON on loongson family machines
+ *
+ *  Copyright (C) 2008-2009 Lemote Inc.
+ *  Author: Yan Hua <yanh@lemote.com>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+
+#include <loongson.h>
+
+#define FLASH_PHYS_ADDR LOONGSON_BOOT_BASE
+#define FLASH_SIZE 0x080000
+
+#define FLASH_PARTITION0_ADDR 0x00000000
+#define FLASH_PARTITION0_SIZE 0x00080000
+
+struct map_info flash_map = {
+	.name = "flash device",
+	.size = FLASH_SIZE,
+	.bankwidth = 1,
+};
+
+struct mtd_partition flash_parts[] = {
+	{
+	 .name = "Bootloader",
+	 .offset = FLASH_PARTITION0_ADDR,
+	 .size = FLASH_PARTITION0_SIZE},
+};
+
+#define PARTITION_COUNT ARRAY_SIZE(flash_parts)
+
+static struct mtd_info *mymtd;
+
+int __init init_flash(void)
+{
+	printk(KERN_NOTICE "flash device: %x at %x\n",
+	       FLASH_SIZE, FLASH_PHYS_ADDR);
+
+	flash_map.phys = FLASH_PHYS_ADDR;
+	flash_map.virt = ioremap(FLASH_PHYS_ADDR, FLASH_SIZE);
+
+	if (!flash_map.virt) {
+		printk(KERN_NOTICE "Failed to ioremap\n");
+		return -EIO;
+	}
+
+	simple_map_init(&flash_map);
+
+	mymtd = do_map_probe("cfi_probe", &flash_map);
+	if (mymtd) {
+		add_mtd_partitions(mymtd, flash_parts, PARTITION_COUNT);
+		printk(KERN_NOTICE "pmon flash device initialized\n");
+		return 0;
+	}
+
+	iounmap((void *)flash_map.virt);
+	return -ENXIO;
+}
+
+static void __exit cleanup_flash(void)
+{
+	if (mymtd) {
+		del_mtd_partitions(mymtd);
+		map_destroy(mymtd);
+	}
+	if (flash_map.virt) {
+		iounmap((void *)flash_map.virt);
+		flash_map.virt = 0;
+	}
+}
+
+module_init(init_flash);
+module_exit(cleanup_flash);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Yanhua <yanh@lemote.com>");
+MODULE_DESCRIPTION("MTD driver for pmon flushing/dumping");
diff -Nur linux-2.6.36.orig/arch/mips/loongson/lemote-2f/Makefile linux-2.6.36/arch/mips/loongson/lemote-2f/Makefile
--- linux-2.6.36.orig/arch/mips/loongson/lemote-2f/Makefile	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/lemote-2f/Makefile	2010-11-18 11:47:59.000000000 +0100
@@ -2,7 +2,7 @@
 # Makefile for lemote loongson2f family machines
 #
 
-obj-y += machtype.o irq.o reset.o ec_kb3310b.o
+obj-y += machtype.o irq.o reset.o ec_kb3310b.o platform.o
 
 #
 # Suspend Support
diff -Nur linux-2.6.36.orig/arch/mips/loongson/lemote-2f/ec_kb3310b.c linux-2.6.36/arch/mips/loongson/lemote-2f/ec_kb3310b.c
--- linux-2.6.36.orig/arch/mips/loongson/lemote-2f/ec_kb3310b.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/lemote-2f/ec_kb3310b.c	2010-11-18 11:47:59.000000000 +0100
@@ -14,7 +14,7 @@
 #include <linux/spinlock.h>
 #include <linux/delay.h>
 
-#include "ec_kb3310b.h"
+#include <ec_kb3310b.h>
 
 static DEFINE_SPINLOCK(index_access_lock);
 static DEFINE_SPINLOCK(port_access_lock);
@@ -78,12 +78,9 @@
 	spin_unlock_irqrestore(&port_access_lock, flags);
 
 	if (timeout <= 0) {
-		printk(KERN_ERR "%s: deadable error : timeout...\n", __func__);
+		pr_err("%s: deadable error : timeout...\n", __func__);
 		ret = -EINVAL;
-	} else
-		printk(KERN_INFO
-			   "(%x/%d)ec issued command %d status : 0x%x\n",
-			   timeout, EC_CMD_TIMEOUT - timeout, cmd, status);
+	}
 
 	return ret;
 }
@@ -118,8 +115,7 @@
 		udelay(EC_REG_DELAY);
 	}
 	if (timeout <= 0) {
-		pr_info("%s: get event number timeout.\n", __func__);
-
+		pr_err("%s: get event number timeout.\n", __func__);
 		return -EINVAL;
 	}
 	value = inb(EC_DAT_PORT);
diff -Nur linux-2.6.36.orig/arch/mips/loongson/lemote-2f/ec_kb3310b.h linux-2.6.36/arch/mips/loongson/lemote-2f/ec_kb3310b.h
--- linux-2.6.36.orig/arch/mips/loongson/lemote-2f/ec_kb3310b.h	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/lemote-2f/ec_kb3310b.h	1970-01-01 01:00:00.000000000 +0100
@@ -1,188 +0,0 @@
-/*
- * KB3310B Embedded Controller
- *
- *  Copyright (C) 2008 Lemote Inc.
- *  Author: liujl <liujl@lemote.com>, 2008-03-14
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-
-#ifndef _EC_KB3310B_H
-#define _EC_KB3310B_H
-
-extern unsigned char ec_read(unsigned short addr);
-extern void ec_write(unsigned short addr, unsigned char val);
-extern int ec_query_seq(unsigned char cmd);
-extern int ec_query_event_num(void);
-extern int ec_get_event_num(void);
-
-typedef int (*sci_handler) (int status);
-extern sci_handler yeeloong_report_lid_status;
-
-#define SCI_IRQ_NUM 0x0A
-
-/*
- * The following registers are determined by the EC index configuration.
- * 1, fill the PORT_HIGH as EC register high part.
- * 2, fill the PORT_LOW as EC register low part.
- * 3, fill the PORT_DATA as EC register write data or get the data from it.
- */
-#define	EC_IO_PORT_HIGH	0x0381
-#define	EC_IO_PORT_LOW	0x0382
-#define	EC_IO_PORT_DATA	0x0383
-
-/*
- * EC delay time is 500us for register and status access
- */
-#define	EC_REG_DELAY	500	/* unit : us */
-#define	EC_CMD_TIMEOUT	0x1000
-
-/*
- * EC access port for SCI communication
- */
-#define	EC_CMD_PORT		0x66
-#define	EC_STS_PORT		0x66
-#define	EC_DAT_PORT		0x62
-#define	CMD_INIT_IDLE_MODE	0xdd
-#define	CMD_EXIT_IDLE_MODE	0xdf
-#define	CMD_INIT_RESET_MODE	0xd8
-#define	CMD_REBOOT_SYSTEM	0x8c
-#define	CMD_GET_EVENT_NUM	0x84
-#define	CMD_PROGRAM_PIECE	0xda
-
-/* temperature & fan registers */
-#define	REG_TEMPERATURE_VALUE	0xF458
-#define	REG_FAN_AUTO_MAN_SWITCH 0xF459
-#define	BIT_FAN_AUTO		0
-#define	BIT_FAN_MANUAL		1
-#define	REG_FAN_CONTROL		0xF4D2
-#define	BIT_FAN_CONTROL_ON	(1 << 0)
-#define	BIT_FAN_CONTROL_OFF	(0 << 0)
-#define	REG_FAN_STATUS		0xF4DA
-#define	BIT_FAN_STATUS_ON	(1 << 0)
-#define	BIT_FAN_STATUS_OFF	(0 << 0)
-#define	REG_FAN_SPEED_HIGH	0xFE22
-#define	REG_FAN_SPEED_LOW	0xFE23
-#define	REG_FAN_SPEED_LEVEL	0xF4CC
-/* fan speed divider */
-#define	FAN_SPEED_DIVIDER	480000	/* (60*1000*1000/62.5/2)*/
-
-/* battery registers */
-#define	REG_BAT_DESIGN_CAP_HIGH		0xF77D
-#define	REG_BAT_DESIGN_CAP_LOW		0xF77E
-#define	REG_BAT_FULLCHG_CAP_HIGH	0xF780
-#define	REG_BAT_FULLCHG_CAP_LOW		0xF781
-#define	REG_BAT_DESIGN_VOL_HIGH		0xF782
-#define	REG_BAT_DESIGN_VOL_LOW		0xF783
-#define	REG_BAT_CURRENT_HIGH		0xF784
-#define	REG_BAT_CURRENT_LOW		0xF785
-#define	REG_BAT_VOLTAGE_HIGH		0xF786
-#define	REG_BAT_VOLTAGE_LOW		0xF787
-#define	REG_BAT_TEMPERATURE_HIGH	0xF788
-#define	REG_BAT_TEMPERATURE_LOW		0xF789
-#define	REG_BAT_RELATIVE_CAP_HIGH	0xF492
-#define	REG_BAT_RELATIVE_CAP_LOW	0xF493
-#define	REG_BAT_VENDOR			0xF4C4
-#define	FLAG_BAT_VENDOR_SANYO		0x01
-#define	FLAG_BAT_VENDOR_SIMPLO		0x02
-#define	REG_BAT_CELL_COUNT		0xF4C6
-#define	FLAG_BAT_CELL_3S1P		0x03
-#define	FLAG_BAT_CELL_3S2P		0x06
-#define	REG_BAT_CHARGE			0xF4A2
-#define	FLAG_BAT_CHARGE_DISCHARGE	0x01
-#define	FLAG_BAT_CHARGE_CHARGE		0x02
-#define	FLAG_BAT_CHARGE_ACPOWER		0x00
-#define	REG_BAT_STATUS			0xF4B0
-#define	BIT_BAT_STATUS_LOW		(1 << 5)
-#define	BIT_BAT_STATUS_DESTROY		(1 << 2)
-#define	BIT_BAT_STATUS_FULL		(1 << 1)
-#define	BIT_BAT_STATUS_IN		(1 << 0)
-#define	REG_BAT_CHARGE_STATUS		0xF4B1
-#define	BIT_BAT_CHARGE_STATUS_OVERTEMP	(1 << 2)
-#define	BIT_BAT_CHARGE_STATUS_PRECHG	(1 << 1)
-#define	REG_BAT_STATE			0xF482
-#define	BIT_BAT_STATE_CHARGING		(1 << 1)
-#define	BIT_BAT_STATE_DISCHARGING	(1 << 0)
-#define	REG_BAT_POWER			0xF440
-#define	BIT_BAT_POWER_S3		(1 << 2)
-#define	BIT_BAT_POWER_ON		(1 << 1)
-#define	BIT_BAT_POWER_ACIN		(1 << 0)
-
-/* other registers */
-/* Audio: rd/wr */
-#define	REG_AUDIO_VOLUME	0xF46C
-#define	REG_AUDIO_MUTE		0xF4E7
-#define	REG_AUDIO_BEEP		0xF4D0
-/* USB port power or not: rd/wr */
-#define	REG_USB0_FLAG		0xF461
-#define	REG_USB1_FLAG		0xF462
-#define	REG_USB2_FLAG		0xF463
-#define	BIT_USB_FLAG_ON		1
-#define	BIT_USB_FLAG_OFF	0
-/* LID */
-#define	REG_LID_DETECT		0xF4BD
-#define	BIT_LID_DETECT_ON	1
-#define	BIT_LID_DETECT_OFF	0
-/* CRT */
-#define	REG_CRT_DETECT		0xF4AD
-#define	BIT_CRT_DETECT_PLUG	1
-#define	BIT_CRT_DETECT_UNPLUG	0
-/* LCD backlight brightness adjust: 9 levels */
-#define	REG_DISPLAY_BRIGHTNESS	0xF4F5
-/* Black screen Status */
-#define	BIT_DISPLAY_LCD_ON	1
-#define	BIT_DISPLAY_LCD_OFF	0
-/* LCD backlight control: off/restore */
-#define	REG_BACKLIGHT_CTRL	0xF7BD
-#define	BIT_BACKLIGHT_ON	1
-#define	BIT_BACKLIGHT_OFF	0
-/* Reset the machine auto-clear: rd/wr */
-#define	REG_RESET		0xF4EC
-#define	BIT_RESET_ON		1
-/* Light the led: rd/wr */
-#define	REG_LED			0xF4C8
-#define	BIT_LED_RED_POWER	(1 << 0)
-#define	BIT_LED_ORANGE_POWER	(1 << 1)
-#define	BIT_LED_GREEN_CHARGE	(1 << 2)
-#define	BIT_LED_RED_CHARGE	(1 << 3)
-#define	BIT_LED_NUMLOCK		(1 << 4)
-/* Test led mode, all led on/off */
-#define	REG_LED_TEST		0xF4C2
-#define	BIT_LED_TEST_IN		1
-#define	BIT_LED_TEST_OUT	0
-/* Camera on/off */
-#define	REG_CAMERA_STATUS	0xF46A
-#define	BIT_CAMERA_STATUS_ON	1
-#define	BIT_CAMERA_STATUS_OFF	0
-#define	REG_CAMERA_CONTROL	0xF7B7
-#define	BIT_CAMERA_CONTROL_OFF	0
-#define	BIT_CAMERA_CONTROL_ON	1
-/* Wlan Status */
-#define	REG_WLAN		0xF4FA
-#define	BIT_WLAN_ON		1
-#define	BIT_WLAN_OFF		0
-#define	REG_DISPLAY_LCD		0xF79F
-
-/* SCI Event Number from EC */
-enum {
-	EVENT_LID = 0x23,	/*  LID open/close */
-	EVENT_DISPLAY_TOGGLE,	/*  Fn+F3 for display switch */
-	EVENT_SLEEP,		/*  Fn+F1 for entering sleep mode */
-	EVENT_OVERTEMP,		/*  Over-temperature happened */
-	EVENT_CRT_DETECT,	/*  CRT is connected */
-	EVENT_CAMERA,		/*  Camera on/off */
-	EVENT_USB_OC2,		/*  USB2 Over Current occurred */
-	EVENT_USB_OC0,		/*  USB0 Over Current occurred */
-	EVENT_BLACK_SCREEN,	/*  Turn on/off backlight */
-	EVENT_AUDIO_MUTE,	/*  Mute on/off */
-	EVENT_DISPLAY_BRIGHTNESS,/* LCD backlight brightness adjust */
-	EVENT_AC_BAT,		/*  AC & Battery relative issue */
-	EVENT_AUDIO_VOLUME,	/*  Volume adjust */
-	EVENT_WLAN,		/*  Wlan on/off */
-	EVENT_END
-};
-
-#endif /* !_EC_KB3310B_H */
diff -Nur linux-2.6.36.orig/arch/mips/loongson/lemote-2f/platform.c linux-2.6.36/arch/mips/loongson/lemote-2f/platform.c
--- linux-2.6.36.orig/arch/mips/loongson/lemote-2f/platform.c	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/arch/mips/loongson/lemote-2f/platform.c	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/err.h>
+#include <linux/platform_device.h>
+
+#include <asm/bootinfo.h>
+
+static struct platform_device yeeloong_pdev = {
+	.name = "yeeloong_laptop",
+	.id = -1,
+};
+
+static struct platform_device lynloong_pdev = {
+	.name = "lynloong_pc",
+	.id = -1,
+};
+
+static int __init lemote2f_platform_init(void)
+{
+	struct platform_device *pdev = NULL;
+
+	switch (mips_machtype) {
+	case MACH_LEMOTE_YL2F89:
+		pdev = &yeeloong_pdev;
+		break;
+	case MACH_LEMOTE_LL2F:
+		pdev = &lynloong_pdev;
+		break;
+	default:
+		break;
+
+	}
+
+	if (pdev != NULL)
+		return platform_device_register(pdev);
+
+	return -ENODEV;
+}
+
+arch_initcall(lemote2f_platform_init);
diff -Nur linux-2.6.36.orig/arch/mips/loongson/lemote-2f/pm.c linux-2.6.36/arch/mips/loongson/lemote-2f/pm.c
--- linux-2.6.36.orig/arch/mips/loongson/lemote-2f/pm.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/lemote-2f/pm.c	2010-11-18 11:47:59.000000000 +0100
@@ -23,7 +23,7 @@
 #include <loongson.h>
 
 #include <cs5536/cs5536_mfgpt.h>
-#include "ec_kb3310b.h"
+#include <ec_kb3310b.h>
 
 #define I8042_KBD_IRQ		1
 #define I8042_CTR_KBDINT	0x01
@@ -100,7 +100,7 @@
 	if (irq < 0)
 		return 0;
 
-	printk(KERN_INFO "%s: irq = %d\n", __func__, irq);
+	pr_info("%s: irq = %d\n", __func__, irq);
 
 	if (irq == I8042_KBD_IRQ)
 		return 1;
diff -Nur linux-2.6.36.orig/arch/mips/loongson/lemote-2f/reset.c linux-2.6.36/arch/mips/loongson/lemote-2f/reset.c
--- linux-2.6.36.orig/arch/mips/loongson/lemote-2f/reset.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/loongson/lemote-2f/reset.c	2010-11-18 11:47:59.000000000 +0100
@@ -20,7 +20,7 @@
 #include <loongson.h>
 
 #include <cs5536/cs5536.h>
-#include "ec_kb3310b.h"
+#include <ec_kb3310b.h>
 
 static void reset_cpu(void)
 {
diff -Nur linux-2.6.36.orig/arch/mips/mm/dma-default.c linux-2.6.36/arch/mips/mm/dma-default.c
--- linux-2.6.36.orig/arch/mips/mm/dma-default.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/arch/mips/mm/dma-default.c	2010-11-18 11:47:59.000000000 +0100
@@ -380,3 +380,16 @@
 }
 
 EXPORT_SYMBOL(dma_cache_sync);
+
+int __weak dma_mmap_coherent(struct device *dev, struct vm_area_struct *vma,
+		void *cpu_addr, dma_addr_t handle, size_t size)
+{
+	struct page *pg;
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+	cpu_addr = (void *)dma_addr_to_virt(dev, handle);
+	pg = virt_to_page(cpu_addr);
+	return remap_pfn_range(vma, vma->vm_start,
+		       page_to_pfn(pg) + vma->vm_pgoff,
+		       size, vma->vm_page_prot);
+}
+EXPORT_SYMBOL(dma_mmap_coherent);
diff -Nur linux-2.6.36.orig/drivers/ide/ide-iops.c linux-2.6.36/drivers/ide/ide-iops.c
--- linux-2.6.36.orig/drivers/ide/ide-iops.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/drivers/ide/ide-iops.c	2010-11-18 11:47:59.000000000 +0100
@@ -27,6 +27,8 @@
 #include <asm/uaccess.h>
 #include <asm/io.h>
 
+#include <asm/bootinfo.h>
+
 void SELECT_MASK(ide_drive_t *drive, int mask)
 {
 	const struct ide_port_ops *port_ops = drive->hwif->port_ops;
@@ -300,6 +302,9 @@
 {
 	const char **list, *m = (char *)&drive->id[ATA_ID_PROD];
 
+	if (mips_machtype != MACH_LEMOTE_YL2F89)
+		return;
+
 	for (list = nien_quirk_list; *list != NULL; list++)
 		if (strstr(m, *list) != NULL) {
 			drive->dev_flags |= IDE_DFLAG_NIEN_QUIRK;
diff -Nur linux-2.6.36.orig/drivers/platform/Kconfig linux-2.6.36/drivers/platform/Kconfig
--- linux-2.6.36.orig/drivers/platform/Kconfig	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/drivers/platform/Kconfig	2010-11-18 11:47:59.000000000 +0100
@@ -1,3 +1,7 @@
 if X86
 source "drivers/platform/x86/Kconfig"
 endif
+
+if MIPS
+source "drivers/platform/mips/Kconfig"
+endif
diff -Nur linux-2.6.36.orig/drivers/platform/Makefile linux-2.6.36/drivers/platform/Makefile
--- linux-2.6.36.orig/drivers/platform/Makefile	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/drivers/platform/Makefile	2010-11-18 11:47:59.000000000 +0100
@@ -3,3 +3,4 @@
 #
 
 obj-$(CONFIG_X86)		+= x86/
+obj-$(CONFIG_MIPS)		+= mips/
diff -Nur linux-2.6.36.orig/drivers/platform/mips/Kconfig linux-2.6.36/drivers/platform/mips/Kconfig
--- linux-2.6.36.orig/drivers/platform/mips/Kconfig	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/drivers/platform/mips/Kconfig	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,43 @@
+#
+# MIPS Platform Specific Drivers
+#
+
+menuconfig MIPS_PLATFORM_DEVICES
+	bool "MIPS Platform Specific Device Drivers"
+	default y
+	help
+	  Say Y here to get to see options for device drivers of various
+	  MIPS platforms, including vendor-specific netbook/laptop/pc extension
+	  drivers.  This option alone does not add any kernel code.
+
+	  If you say N, all options in this submenu will be skipped and disabled.
+
+if MIPS_PLATFORM_DEVICES
+
+config LEMOTE_YEELOONG2F
+	tristate "Lemote YeeLoong Laptop"
+	depends on LEMOTE_MACH2F
+	select BACKLIGHT_CLASS_DEVICE
+	select POWER_SUPPLY
+	select HWMON
+	select VIDEO_OUTPUT_CONTROL
+	select INPUT_SPARSEKMAP
+	depends on INPUT
+	help
+	  YeeLoong netbook is a mini laptop made by Lemote, which is basically
+	  compatible to FuLoong2F mini PC, but it has an extra Embedded
+	  Controller(kb3310b) for battery, hotkey, backlight, temperature and
+	  fan management.
+
+config LEMOTE_LYNLOONG2F
+	tristate "Lemote LynLoong PC"
+	depends on LEMOTE_MACH2F
+	select BACKLIGHT_CLASS_DEVICE
+	select VIDEO_OUTPUT_CONTROL
+	help
+	  LynLoong PC is an AllINONE machine made by Lemote, which is basically
+	  compatible to FuLoong2F Mini PC, the only difference is that it has a
+	  size-fixed screen: 1360x768 with sisfb video driver. and also, it has
+	  its own specific suspend support.
+
+endif # MIPS_PLATFORM_DEVICES
diff -Nur linux-2.6.36.orig/drivers/platform/mips/Makefile linux-2.6.36/drivers/platform/mips/Makefile
--- linux-2.6.36.orig/drivers/platform/mips/Makefile	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/drivers/platform/mips/Makefile	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,7 @@
+#
+# Makefile for MIPS Platform-Specific Drivers
+#
+
+obj-$(CONFIG_LEMOTE_YEELOONG2F)	+= yeeloong_laptop.o
+
+obj-$(CONFIG_LEMOTE_LYNLOONG2F)	+= lynloong_pc.o
diff -Nur linux-2.6.36.orig/drivers/platform/mips/lynloong_pc.c linux-2.6.36/drivers/platform/mips/lynloong_pc.c
--- linux-2.6.36.orig/drivers/platform/mips/lynloong_pc.c	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/drivers/platform/mips/lynloong_pc.c	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,513 @@
+/*
+ * Driver for LynLoong PC extras
+ *
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>, Xiang Yu <xiangy@lemote.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/backlight.h>	/* for backlight subdriver */
+#include <linux/fb.h>
+#include <linux/video_output.h>	/* for video output subdriver */
+#include <linux/delay.h>	/* for suspend support */
+
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_mfgpt.h>
+
+#include <loongson.h>
+
+static u32 gpio_base, mfgpt_base;
+
+static void set_gpio_reg_high(int gpio, int reg)
+{
+	u32 val;
+
+	val = inl(gpio_base + reg);
+	val |= (1 << gpio);
+	val &= ~(1 << (16 + gpio));
+	outl(val, gpio_base + reg);
+	mmiowb();
+}
+
+static void set_gpio_reg_low(int gpio, int reg)
+{
+	u32 val;
+
+	val = inl(gpio_base + reg);
+	val |= (1 << (16 + gpio));
+	val &= ~(1 << gpio);
+	outl(val, gpio_base + reg);
+	mmiowb();
+}
+
+static void set_gpio_output_low(int gpio)
+{
+	set_gpio_reg_high(gpio, GPIOL_OUT_EN);
+	set_gpio_reg_low(gpio, GPIOL_OUT_VAL);
+}
+
+static void set_gpio_output_high(int gpio)
+{
+	set_gpio_reg_high(gpio, GPIOL_OUT_EN);
+	set_gpio_reg_high(gpio, GPIOL_OUT_VAL);
+}
+
+/* backlight subdriver */
+
+#define MAX_BRIGHTNESS 100
+#define DEFAULT_BRIGHTNESS 50
+#define MIN_BRIGHTNESS 0
+static unsigned int level;
+
+DEFINE_SPINLOCK(backlight_lock);
+/* Tune the brightness */
+static void setup_mfgpt2(void)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&backlight_lock, flags);
+
+	/* Set MFGPT2 comparator 1,2 */
+	outw(MAX_BRIGHTNESS-level, MFGPT2_CMP1);
+	outw(MAX_BRIGHTNESS, MFGPT2_CMP2);
+	/* Clear MFGPT2 UP COUNTER */
+	outw(0, MFGPT2_CNT);
+	/* Enable counter, compare mode, 32k */
+	outw(0x8280, MFGPT2_SETUP);
+
+	spin_unlock_irqrestore(&backlight_lock, flags);
+}
+
+static int lynloong_set_brightness(struct backlight_device *bd)
+{
+	level = (bd->props.fb_blank == FB_BLANK_UNBLANK &&
+		 bd->props.power == FB_BLANK_UNBLANK) ?
+	    bd->props.brightness : 0;
+
+	if (level > MAX_BRIGHTNESS)
+		level = MAX_BRIGHTNESS;
+	else if (level < MIN_BRIGHTNESS)
+		level = MIN_BRIGHTNESS;
+
+	setup_mfgpt2();
+
+	return 0;
+}
+
+static int lynloong_get_brightness(struct backlight_device *bd)
+{
+	return level;
+}
+
+static struct backlight_ops backlight_ops = {
+	.get_brightness = lynloong_get_brightness,
+	.update_status = lynloong_set_brightness,
+};
+
+static struct backlight_device *lynloong_backlight_dev;
+
+static int lynloong_backlight_init(void)
+{
+	int ret;
+	u32 hi;
+	struct backlight_properties props;
+
+	/* Get gpio_base */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &gpio_base);
+	/* Get mfgpt_base */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &hi, &mfgpt_base);
+	/* Get gpio_base */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &gpio_base);
+
+	/* Select for mfgpt */
+	set_gpio_reg_high(7, GPIOL_OUT_AUX1_SEL);
+	/* Enable brightness controlling */
+	set_gpio_output_high(7);
+
+	memset(&props, 0, sizeof(struct backlight_properties));
+	props.max_brightness = MAX_BRIGHTNESS;
+	lynloong_backlight_dev = backlight_device_register("backlight0", NULL,
+			NULL, &backlight_ops, &props);
+
+	if (IS_ERR(lynloong_backlight_dev)) {
+		ret = PTR_ERR(lynloong_backlight_dev);
+		return ret;
+	}
+
+	lynloong_backlight_dev->props.brightness = DEFAULT_BRIGHTNESS;
+	backlight_update_status(lynloong_backlight_dev);
+
+	return 0;
+}
+
+static void lynloong_backlight_exit(void)
+{
+	if (lynloong_backlight_dev) {
+		backlight_device_unregister(lynloong_backlight_dev);
+		lynloong_backlight_dev = NULL;
+	}
+	/* Disable brightness controlling */
+	set_gpio_output_low(7);
+}
+
+/* video output driver */
+static int vo_status = 1;
+
+static int lcd_video_output_get(struct output_device *od)
+{
+	return vo_status;
+}
+
+static int lcd_video_output_set(struct output_device *od)
+{
+	int i;
+	unsigned long status;
+
+	status = !!od->request_state;
+
+	if (status == 0) {
+		/* Set the current status as off */
+		vo_status = 0;
+		/* Turn off the backlight */
+		set_gpio_output_low(11);
+		for (i = 0; i < 0x500; i++)
+			delay();
+		/* Turn off the LCD */
+		set_gpio_output_high(8);
+	} else {
+		/* Turn on the LCD */
+		set_gpio_output_low(8);
+		for (i = 0; i < 0x500; i++)
+			delay();
+		/* Turn on the backlight */
+		set_gpio_output_high(11);
+		/* Set the current status as on */
+		vo_status = 1;
+	}
+
+	return 0;
+}
+
+static struct output_properties lcd_output_properties = {
+	.set_state = lcd_video_output_set,
+	.get_status = lcd_video_output_get,
+};
+
+static struct output_device *lcd_output_dev;
+
+static void lynloong_lcd_vo_set(int status)
+{
+	lcd_output_dev->request_state = status;
+	lcd_video_output_set(lcd_output_dev);
+}
+
+static int lynloong_vo_init(void)
+{
+	int ret;
+
+	/* Register video output device: lcd */
+	lcd_output_dev = video_output_register("LCD", NULL, NULL,
+			&lcd_output_properties);
+
+	if (IS_ERR(lcd_output_dev)) {
+		ret = PTR_ERR(lcd_output_dev);
+		lcd_output_dev = NULL;
+		return ret;
+	}
+	/* Ensure LCD is on by default */
+	lynloong_lcd_vo_set(1);
+
+	return 0;
+}
+
+static void lynloong_vo_exit(void)
+{
+	if (lcd_output_dev) {
+		video_output_unregister(lcd_output_dev);
+		lcd_output_dev = NULL;
+	}
+}
+
+/* suspend support */
+
+#ifdef CONFIG_PM
+
+static u32 smb_base;
+
+/* I2C operations */
+
+static int i2c_wait(void)
+{
+	char c;
+	int i;
+
+	udelay(1000);
+	for (i = 0; i < 20; i++) {
+		c = inb(smb_base | SMB_STS);
+		if (c & (SMB_STS_BER | SMB_STS_NEGACK))
+			return -1;
+		if (c & SMB_STS_SDAST)
+			return 0;
+		udelay(100);
+	}
+	return -2;
+}
+
+static void i2c_read_single(int addr, int regNo, char *value)
+{
+	unsigned char c;
+
+	/* Start condition */
+	c = inb(smb_base | SMB_CTRL1);
+	outb(c | SMB_CTRL1_START, smb_base | SMB_CTRL1);
+	i2c_wait();
+
+	/* Send slave address */
+	outb(addr & 0xfe, smb_base | SMB_SDA);
+	i2c_wait();
+
+	/* Acknowledge smbus */
+	c = inb(smb_base | SMB_CTRL1);
+	outb(c | SMB_CTRL1_ACK, smb_base | SMB_CTRL1);
+
+	/* Send register index */
+	outb(regNo, smb_base | SMB_SDA);
+	i2c_wait();
+
+	/* Acknowledge smbus */
+	c = inb(smb_base | SMB_CTRL1);
+	outb(c | SMB_CTRL1_ACK, smb_base | SMB_CTRL1);
+
+	/* Start condition again */
+	c = inb(smb_base | SMB_CTRL1);
+	outb(c | SMB_CTRL1_START, smb_base | SMB_CTRL1);
+	i2c_wait();
+
+	/* Send salve address again */
+	outb(1 | addr, smb_base | SMB_SDA);
+	i2c_wait();
+
+	/* Acknowledge smbus */
+	c = inb(smb_base | SMB_CTRL1);
+	outb(c | SMB_CTRL1_ACK, smb_base | SMB_CTRL1);
+
+	/* Read data */
+	*value = inb(smb_base | SMB_SDA);
+
+	/* Stop condition */
+	outb(SMB_CTRL1_STOP, smb_base | SMB_CTRL1);
+	i2c_wait();
+}
+
+static void i2c_write_single(int addr, int regNo, char value)
+{
+	unsigned char c;
+
+	/* Start condition */
+	c = inb(smb_base | SMB_CTRL1);
+	outb(c | SMB_CTRL1_START, smb_base | SMB_CTRL1);
+	i2c_wait();
+	/* Send slave address */
+	outb(addr & 0xfe, smb_base | SMB_SDA);
+	i2c_wait();;
+
+	/* Send register index */
+	outb(regNo, smb_base | SMB_SDA);
+	i2c_wait();
+
+	/* Write data */
+	outb(value, smb_base | SMB_SDA);
+	i2c_wait();
+	/* Stop condition */
+	outb(SMB_CTRL1_STOP, smb_base | SMB_CTRL1);
+	i2c_wait();
+}
+
+static void stop_clock(int clk_reg, int clk_sel)
+{
+	u8 value;
+
+	i2c_read_single(0xd3, clk_reg, &value);
+	value &= ~(1 << clk_sel);
+	i2c_write_single(0xd2, clk_reg, value);
+}
+
+static void enable_clock(int clk_reg, int clk_sel)
+{
+	u8 value;
+
+	i2c_read_single(0xd3, clk_reg, &value);
+	value |= (1 << clk_sel);
+	i2c_write_single(0xd2, clk_reg, value);
+}
+
+static char cached_clk_freq;
+static char cached_pci_fixed_freq;
+
+static void decrease_clk_freq(void)
+{
+	char value;
+
+	i2c_read_single(0xd3, 1, &value);
+	cached_clk_freq = value;
+
+	/* Select frequency by software */
+	value |= (1 << 1);
+	/* CPU, 3V66, PCI : 100, 66, 33(1) */
+	value |= (1 << 2);
+	i2c_write_single(0xd2, 1, value);
+
+	/* Cache the pci frequency */
+	i2c_read_single(0xd3, 14, &value);
+	cached_pci_fixed_freq = value;
+
+	/* Enable PCI fix mode */
+	value |= (1 << 5);
+	/* 3V66, PCI : 64MHz, 32MHz */
+	value |= (1 << 3);
+	i2c_write_single(0xd2, 14, value);
+
+}
+
+static void resume_clk_freq(void)
+{
+	i2c_write_single(0xd2, 1, cached_clk_freq);
+	i2c_write_single(0xd2, 14, cached_pci_fixed_freq);
+}
+
+static void stop_clocks(void)
+{
+	/* CPU Clock Register */
+	stop_clock(2, 5);	/* not used */
+	stop_clock(2, 6);	/* not used */
+	stop_clock(2, 7);	/* not used */
+
+	/* PCI Clock Register */
+	stop_clock(3, 1);	/* 8100 */
+	stop_clock(3, 5);	/* SIS */
+	stop_clock(3, 0);	/* not used */
+	stop_clock(3, 6);	/* not used */
+
+	/* PCI 48M Clock Register */
+	stop_clock(4, 6);	/* USB grounding */
+	stop_clock(4, 5);	/* REF(5536_14M) */
+
+	/* 3V66 Control Register */
+	stop_clock(5, 0);	/* VCH_CLK..., grounding */
+}
+
+static void enable_clocks(void)
+{
+	enable_clock(3, 1);	/* 8100 */
+	enable_clock(3, 5);	/* SIS */
+
+	enable_clock(4, 6);
+	enable_clock(4, 5);	/* REF(5536_14M) */
+
+	enable_clock(5, 0);	/* VCH_CLOCK, grounding */
+}
+
+static int lynloong_suspend(struct device *dev)
+{
+	/* Disable AMP */
+	set_gpio_output_high(6);
+	/* Turn off LCD */
+	lynloong_lcd_vo_set(0);
+
+	/* Stop the clocks of some devices */
+	stop_clocks();
+
+	/* Decrease the external clock frequency */
+	decrease_clk_freq();
+
+	return 0;
+}
+
+static int lynloong_resume(struct device *dev)
+{
+	/* Turn on the LCD */
+	lynloong_lcd_vo_set(1);
+
+	/* Resume clock frequency, enable the relative clocks */
+	resume_clk_freq();
+	enable_clocks();
+
+	/* Enable AMP */
+	set_gpio_output_low(6);
+
+	return 0;
+}
+
+static const SIMPLE_DEV_PM_OPS(lynloong_pm_ops, lynloong_suspend,
+	lynloong_resume);
+#endif	/* !CONFIG_PM */
+
+static struct platform_device_id platform_device_ids[] = {
+	{
+		.name = "lynloong_pc",
+	},
+	{}
+};
+
+MODULE_DEVICE_TABLE(platform, platform_device_ids);
+
+static struct platform_driver platform_driver = {
+	.driver = {
+		.name = "lynloong_pc",
+		.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+		.pm = &lynloong_pm_ops,
+#endif
+	},
+	.id_table = platform_device_ids,
+};
+
+static int __init lynloong_init(void)
+{
+	int ret;
+
+	pr_info("Load LynLoong Platform Specific Driver.\n");
+
+	/* Register platform stuff */
+	ret = platform_driver_register(&platform_driver);
+	if (ret) {
+		pr_err("Fail to register lynloong platform driver.\n");
+		return ret;
+	}
+
+	ret = lynloong_backlight_init();
+	if (ret) {
+		pr_err("Fail to register lynloong backlight driver.\n");
+		return ret;
+	}
+
+	ret = lynloong_vo_init();
+	if (ret) {
+		pr_err("Fail to register lynloong backlight driver.\n");
+		lynloong_vo_exit();
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit lynloong_exit(void)
+{
+	lynloong_vo_exit();
+	lynloong_backlight_exit();
+	platform_driver_unregister(&platform_driver);
+
+	pr_info("Unload LynLoong Platform Specific Driver.\n");
+}
+
+module_init(lynloong_init);
+module_exit(lynloong_exit);
+
+MODULE_AUTHOR("Wu Zhangjin <wuzhangjin@gmail.com>; Xiang Yu <xiangy@lemote.com>");
+MODULE_DESCRIPTION("LynLoong PC driver");
+MODULE_LICENSE("GPL");
diff -Nur linux-2.6.36.orig/drivers/platform/mips/yeeloong_ecrom.c linux-2.6.36/drivers/platform/mips/yeeloong_ecrom.c
--- linux-2.6.36.orig/drivers/platform/mips/yeeloong_ecrom.c	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/drivers/platform/mips/yeeloong_ecrom.c	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,943 @@
+/*
+ * Driver for flushing/dumping ROM of EC on YeeLoong laptop
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: liujl <liujl@lemote.com>
+ *
+ * NOTE :
+ * 	The EC resources accessing and programming are supported.
+ */
+
+#include <linux/proc_fs.h>
+#include <linux/miscdevice.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+
+#include <ec_kb3310b.h>
+
+#define	EC_MISC_DEV		"ec_misc"
+#define EC_IOC_MAGIC		'E'
+
+/* ec registers range */
+#define	EC_MAX_REGADDR	0xFFFF
+#define	EC_MIN_REGADDR	0xF000
+#define	EC_RAM_ADDR	0xF800
+
+/* version burned address */
+#define	VER_ADDR	0xf7a1
+#define	VER_MAX_SIZE	7
+#define	EC_ROM_MAX_SIZE	0x10000
+
+/* ec internal register */
+#define	REG_POWER_MODE		0xF710
+#define	FLAG_NORMAL_MODE	0x00
+#define	FLAG_IDLE_MODE		0x01
+#define	FLAG_RESET_MODE		0x02
+
+/* ec update program flag */
+#define	PROGRAM_FLAG_NONE	0x00
+#define	PROGRAM_FLAG_IE		0x01
+#define	PROGRAM_FLAG_ROM	0x02
+
+/* XBI relative registers */
+#define REG_XBISEG0     0xFEA0
+#define REG_XBISEG1     0xFEA1
+#define REG_XBIRSV2     0xFEA2
+#define REG_XBIRSV3     0xFEA3
+#define REG_XBIRSV4     0xFEA4
+#define REG_XBICFG      0xFEA5
+#define REG_XBICS       0xFEA6
+#define REG_XBIWE       0xFEA7
+#define REG_XBISPIA0    0xFEA8
+#define REG_XBISPIA1    0xFEA9
+#define REG_XBISPIA2    0xFEAA
+#define REG_XBISPIDAT   0xFEAB
+#define REG_XBISPICMD   0xFEAC
+#define REG_XBISPICFG   0xFEAD
+#define REG_XBISPIDATR  0xFEAE
+#define REG_XBISPICFG2  0xFEAF
+
+/* commands definition for REG_XBISPICMD */
+#define	SPICMD_WRITE_STATUS		0x01
+#define	SPICMD_BYTE_PROGRAM		0x02
+#define	SPICMD_READ_BYTE		0x03
+#define	SPICMD_WRITE_DISABLE	0x04
+#define	SPICMD_READ_STATUS		0x05
+#define	SPICMD_WRITE_ENABLE		0x06
+#define	SPICMD_HIGH_SPEED_READ	0x0B
+#define	SPICMD_POWER_DOWN		0xB9
+#define	SPICMD_SST_EWSR			0x50
+#define	SPICMD_SST_SEC_ERASE	0x20
+#define	SPICMD_SST_BLK_ERASE	0x52
+#define	SPICMD_SST_CHIP_ERASE	0x60
+#define	SPICMD_FRDO				0x3B
+#define	SPICMD_SEC_ERASE		0xD7
+#define	SPICMD_BLK_ERASE		0xD8
+#define SPICMD_CHIP_ERASE		0xC7
+
+/* bits definition for REG_XBISPICFG */
+#define	SPICFG_AUTO_CHECK		0x01
+#define	SPICFG_SPI_BUSY			0x02
+#define	SPICFG_DUMMY_READ		0x04
+#define	SPICFG_EN_SPICMD		0x08
+#define	SPICFG_LOW_SPICS		0x10
+#define	SPICFG_EN_SHORT_READ	0x20
+#define	SPICFG_EN_OFFSET_READ	0x40
+#define	SPICFG_EN_FAST_READ		0x80
+
+/* watchdog timer registers */
+#define	REG_WDTCFG				0xfe80
+#define	REG_WDTPF				0xfe81
+#define REG_WDT					0xfe82
+
+/* lpc configure register */
+#define	REG_LPCCFG				0xfe95
+
+/* 8051 reg */
+#define	REG_PXCFG				0xff14
+
+/* Fan register in KB3310 */
+#define	REG_ECFAN_SPEED_LEVEL	0xf4e4
+#define	REG_ECFAN_SWITCH		0xf4d2
+
+/* the ec flash rom id number */
+#define	EC_ROM_PRODUCT_ID_SPANSION	0x01
+#define	EC_ROM_PRODUCT_ID_MXIC		0xC2
+#define	EC_ROM_PRODUCT_ID_AMIC		0x37
+#define	EC_ROM_PRODUCT_ID_EONIC		0x1C
+
+/* misc ioctl operations */
+#define	IOCTL_RDREG		_IOR(EC_IOC_MAGIC, 1, int)
+#define	IOCTL_WRREG		_IOW(EC_IOC_MAGIC, 2, int)
+#define	IOCTL_READ_EC		_IOR(EC_IOC_MAGIC, 3, int)
+#define	IOCTL_PROGRAM_IE	_IOW(EC_IOC_MAGIC, 4, int)
+#define	IOCTL_PROGRAM_EC	_IOW(EC_IOC_MAGIC, 5, int)
+
+/* start address for programming of EC content or IE */
+/*  ec running code start address */
+#define	EC_START_ADDR	0x00000000
+/*  ec information element storing address */
+#define	IE_START_ADDR	0x00020000
+
+/* EC state */
+#define	EC_STATE_IDLE	0x00	/*  ec in idle state */
+#define	EC_STATE_BUSY	0x01	/*  ec in busy state */
+
+/* timeout value for programming */
+#define	EC_FLASH_TIMEOUT	0x1000	/*  ec program timeout */
+/* command checkout timeout including cmd to port or state flag check */
+#define	EC_CMD_TIMEOUT		0x1000
+#define	EC_SPICMD_STANDARD_TIMEOUT	(4 * 1000)	/*  unit : us */
+#define	EC_MAX_DELAY_UNIT	(10)	/*  every time for polling */
+#define	SPI_FINISH_WAIT_TIME	10
+/* EC content max size */
+#define	EC_CONTENT_MAX_SIZE	(64 * 1024)
+#define	IE_CONTENT_MAX_SIZE	(0x100000 - IE_START_ADDR)
+
+/* the register operation access struct */
+struct ec_reg {
+	u32 addr;		/* the address of kb3310 registers */
+	u8 val;			/* the register value */
+};
+
+struct ec_info {
+	u32 start_addr;
+	u32 size;
+	u8 *buf;
+};
+
+/* open for using rom protection action */
+#define	EC_ROM_PROTECTION
+
+/* enable the chip reset mode */
+static int ec_init_reset_mode(void)
+{
+	int timeout;
+	unsigned char status = 0;
+	int ret = 0;
+
+	/* make chip goto reset mode */
+	ret = ec_query_seq(CMD_INIT_RESET_MODE);
+	if (ret < 0) {
+		printk(KERN_ERR "ec init reset mode failed.\n");
+		goto out;
+	}
+
+	/* make the action take active */
+	timeout = EC_CMD_TIMEOUT;
+	status = ec_read(REG_POWER_MODE) & FLAG_RESET_MODE;
+	while (timeout--) {
+		if (status) {
+			udelay(EC_REG_DELAY);
+			break;
+		}
+		status = ec_read(REG_POWER_MODE) & FLAG_RESET_MODE;
+		udelay(EC_REG_DELAY);
+	}
+	if (timeout <= 0) {
+		printk(KERN_ERR "ec rom fixup : can't check reset status.\n");
+		ret = -EINVAL;
+	} else
+		printk(KERN_INFO "(%d/%d)reset 0xf710 :  0x%x\n", timeout,
+			   EC_CMD_TIMEOUT - timeout, status);
+
+	/* set MCU to reset mode */
+	udelay(EC_REG_DELAY);
+	status = ec_read(REG_PXCFG);
+	status |= (1 << 0);
+	ec_write(REG_PXCFG, status);
+	udelay(EC_REG_DELAY);
+
+	/* disable FWH/LPC */
+	udelay(EC_REG_DELAY);
+	status = ec_read(REG_LPCCFG);
+	status &= ~(1 << 7);
+	ec_write(REG_LPCCFG, status);
+	udelay(EC_REG_DELAY);
+
+	printk(KERN_INFO "entering reset mode ok..............\n");
+
+ out:
+	return ret;
+}
+
+/* make ec exit from reset mode */
+static void ec_exit_reset_mode(void)
+{
+	unsigned char regval;
+
+	udelay(EC_REG_DELAY);
+	regval = ec_read(REG_LPCCFG);
+	regval |= (1 << 7);
+	ec_write(REG_LPCCFG, regval);
+	regval = ec_read(REG_PXCFG);
+	regval &= ~(1 << 0);
+	ec_write(REG_PXCFG, regval);
+	printk(KERN_INFO "exit reset mode ok..................\n");
+
+	return;
+}
+
+/* make ec disable WDD */
+static void ec_disable_WDD(void)
+{
+	unsigned char status;
+
+	udelay(EC_REG_DELAY);
+	status = ec_read(REG_WDTCFG);
+	ec_write(REG_WDTPF, 0x03);
+	ec_write(REG_WDTCFG, (status & 0x80) | 0x48);
+	printk(KERN_INFO "Disable WDD ok..................\n");
+
+	return;
+}
+
+/* make ec enable WDD */
+static void ec_enable_WDD(void)
+{
+	unsigned char status;
+
+	udelay(EC_REG_DELAY);
+	status = ec_read(REG_WDTCFG);
+	ec_write(REG_WDT, 0x28);	/* set WDT 5sec(0x28) */
+	ec_write(REG_WDTCFG, (status & 0x80) | 0x03);
+	printk(KERN_INFO "Enable WDD ok..................\n");
+
+	return;
+}
+
+/* make ec goto idle mode */
+static int ec_init_idle_mode(void)
+{
+	int timeout;
+	unsigned char status = 0;
+	int ret = 0;
+
+	ec_query_seq(CMD_INIT_IDLE_MODE);
+
+	/* make the action take active */
+	timeout = EC_CMD_TIMEOUT;
+	status = ec_read(REG_POWER_MODE) & FLAG_IDLE_MODE;
+	while (timeout--) {
+		if (status) {
+			udelay(EC_REG_DELAY);
+			break;
+		}
+		status = ec_read(REG_POWER_MODE) & FLAG_IDLE_MODE;
+		udelay(EC_REG_DELAY);
+	}
+	if (timeout <= 0) {
+		printk(KERN_ERR "ec rom fixup : can't check out the status.\n");
+		ret = -EINVAL;
+	} else
+		printk(KERN_INFO "(%d/%d)0xf710 :  0x%x\n", timeout,
+			   EC_CMD_TIMEOUT - timeout, ec_read(REG_POWER_MODE));
+
+	printk(KERN_INFO "entering idle mode ok...................\n");
+
+	return ret;
+}
+
+/* make ec exit from idle mode */
+static int ec_exit_idle_mode(void)
+{
+
+	ec_query_seq(CMD_EXIT_IDLE_MODE);
+
+	printk(KERN_INFO "exit idle mode ok...................\n");
+
+	return 0;
+}
+
+static int ec_instruction_cycle(void)
+{
+	unsigned long timeout;
+	int ret = 0;
+
+	timeout = EC_FLASH_TIMEOUT;
+	while (timeout-- >= 0) {
+		if (!(ec_read(REG_XBISPICFG) & SPICFG_SPI_BUSY))
+			break;
+	}
+	if (timeout <= 0) {
+		printk(KERN_ERR
+		       "EC_INSTRUCTION_CYCLE : timeout for check flag.\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+ out:
+	return ret;
+}
+
+/* To see if the ec is in busy state or not. */
+static inline int ec_flash_busy(unsigned long timeout)
+{
+	/* assurance the first command be going to rom */
+	if (ec_instruction_cycle() < 0)
+		return EC_STATE_BUSY;
+#if 1
+	timeout = timeout / EC_MAX_DELAY_UNIT;
+	while (timeout-- > 0) {
+		/* check the rom's status of busy flag */
+		ec_write(REG_XBISPICMD, SPICMD_READ_STATUS);
+		if (ec_instruction_cycle() < 0)
+			return EC_STATE_BUSY;
+		if ((ec_read(REG_XBISPIDAT) & 0x01) == 0x00)
+			return EC_STATE_IDLE;
+		udelay(EC_MAX_DELAY_UNIT);
+	}
+	if (timeout <= 0) {
+		printk(KERN_ERR
+		       "EC_FLASH_BUSY : timeout for check rom flag.\n");
+		return EC_STATE_BUSY;
+	}
+#else
+	/* check the rom's status of busy flag */
+	ec_write(REG_XBISPICMD, SPICMD_READ_STATUS);
+	if (ec_instruction_cycle() < 0)
+		return EC_STATE_BUSY;
+
+	timeout = timeout / EC_MAX_DELAY_UNIT;
+	while (timeout-- > 0) {
+		if ((ec_read(REG_XBISPIDAT) & 0x01) == 0x00)
+			return EC_STATE_IDLE;
+		udelay(EC_MAX_DELAY_UNIT);
+	}
+	if (timeout <= 0) {
+		printk(KERN_ERR
+		       "EC_FLASH_BUSY : timeout for check rom flag.\n");
+		return EC_STATE_BUSY;
+	}
+#endif
+
+	return EC_STATE_IDLE;
+}
+
+static int rom_instruction_cycle(unsigned char cmd)
+{
+	unsigned long timeout = 0;
+
+	switch (cmd) {
+	case SPICMD_READ_STATUS:
+	case SPICMD_WRITE_ENABLE:
+	case SPICMD_WRITE_DISABLE:
+	case SPICMD_READ_BYTE:
+	case SPICMD_HIGH_SPEED_READ:
+		timeout = 0;
+		break;
+	case SPICMD_WRITE_STATUS:
+		timeout = 300 * 1000;
+		break;
+	case SPICMD_BYTE_PROGRAM:
+		timeout = 5 * 1000;
+		break;
+	case SPICMD_SST_SEC_ERASE:
+	case SPICMD_SEC_ERASE:
+		timeout = 1000 * 1000;
+		break;
+	case SPICMD_SST_BLK_ERASE:
+	case SPICMD_BLK_ERASE:
+		timeout = 3 * 1000 * 1000;
+		break;
+	case SPICMD_SST_CHIP_ERASE:
+	case SPICMD_CHIP_ERASE:
+		timeout = 20 * 1000 * 1000;
+		break;
+	default:
+		timeout = EC_SPICMD_STANDARD_TIMEOUT;
+	}
+	if (timeout == 0)
+		return ec_instruction_cycle();
+	if (timeout < EC_SPICMD_STANDARD_TIMEOUT)
+		timeout = EC_SPICMD_STANDARD_TIMEOUT;
+
+	return ec_flash_busy(timeout);
+}
+
+/* delay for start/stop action */
+static void delay_spi(int n)
+{
+	while (n--)
+		inb(EC_IO_PORT_HIGH);
+}
+
+/* start the action to spi rom function */
+static void ec_start_spi(void)
+{
+	unsigned char val;
+
+	delay_spi(SPI_FINISH_WAIT_TIME);
+	val = ec_read(REG_XBISPICFG) | SPICFG_EN_SPICMD | SPICFG_AUTO_CHECK;
+	ec_write(REG_XBISPICFG, val);
+	delay_spi(SPI_FINISH_WAIT_TIME);
+}
+
+/* stop the action to spi rom function */
+static void ec_stop_spi(void)
+{
+	unsigned char val;
+
+	delay_spi(SPI_FINISH_WAIT_TIME);
+	val =
+	    ec_read(REG_XBISPICFG) & (~(SPICFG_EN_SPICMD | SPICFG_AUTO_CHECK));
+	ec_write(REG_XBISPICFG, val);
+	delay_spi(SPI_FINISH_WAIT_TIME);
+}
+
+/* read one byte from xbi interface */
+static int ec_read_byte(unsigned int addr, unsigned char *byte)
+{
+	int ret = 0;
+
+	/* enable spicmd writing. */
+	ec_start_spi();
+
+	/* enable write spi flash */
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_ENABLE);
+	if (rom_instruction_cycle(SPICMD_WRITE_ENABLE) == EC_STATE_BUSY) {
+		printk(KERN_ERR "EC_READ_BYTE : SPICMD_WRITE_ENABLE failed.\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* write the address */
+	ec_write(REG_XBISPIA2, (addr & 0xff0000) >> 16);
+	ec_write(REG_XBISPIA1, (addr & 0x00ff00) >> 8);
+	ec_write(REG_XBISPIA0, (addr & 0x0000ff) >> 0);
+	/* start action */
+	ec_write(REG_XBISPICMD, SPICMD_HIGH_SPEED_READ);
+	if (rom_instruction_cycle(SPICMD_HIGH_SPEED_READ) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_READ_BYTE : SPICMD_HIGH_SPEED_READ failed.\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	*byte = ec_read(REG_XBISPIDAT);
+
+ out:
+	/* disable spicmd writing. */
+	ec_stop_spi();
+
+	return ret;
+}
+
+/* write one byte to ec rom */
+static int ec_write_byte(unsigned int addr, unsigned char byte)
+{
+	int ret = 0;
+
+	/* enable spicmd writing. */
+	ec_start_spi();
+
+	/* enable write spi flash */
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_ENABLE);
+	if (rom_instruction_cycle(SPICMD_WRITE_ENABLE) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_WRITE_BYTE : SPICMD_WRITE_ENABLE failed.\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* write the address */
+	ec_write(REG_XBISPIA2, (addr & 0xff0000) >> 16);
+	ec_write(REG_XBISPIA1, (addr & 0x00ff00) >> 8);
+	ec_write(REG_XBISPIA0, (addr & 0x0000ff) >> 0);
+	ec_write(REG_XBISPIDAT, byte);
+	/* start action */
+	ec_write(REG_XBISPICMD, SPICMD_BYTE_PROGRAM);
+	if (rom_instruction_cycle(SPICMD_BYTE_PROGRAM) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_WRITE_BYTE : SPICMD_BYTE_PROGRAM failed.\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+ out:
+	/* disable spicmd writing. */
+	ec_stop_spi();
+
+	return ret;
+}
+
+/* unprotect SPI ROM */
+/* EC_ROM_unprotect function code */
+static int EC_ROM_unprotect(void)
+{
+	unsigned char status;
+
+	/* enable write spi flash */
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_ENABLE);
+	if (rom_instruction_cycle(SPICMD_WRITE_ENABLE) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_UNIT_ERASE : SPICMD_WRITE_ENABLE failed.\n");
+		return 1;
+	}
+
+	/* unprotect the status register of rom */
+	ec_write(REG_XBISPICMD, SPICMD_READ_STATUS);
+	if (rom_instruction_cycle(SPICMD_READ_STATUS) == EC_STATE_BUSY) {
+		printk(KERN_ERR "EC_UNIT_ERASE : SPICMD_READ_STATUS failed.\n");
+		return 1;
+	}
+	status = ec_read(REG_XBISPIDAT);
+	ec_write(REG_XBISPIDAT, status & 0x02);
+	if (ec_instruction_cycle() < 0) {
+		printk(KERN_ERR "EC_UNIT_ERASE : write status value failed.\n");
+		return 1;
+	}
+
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_STATUS);
+	if (rom_instruction_cycle(SPICMD_WRITE_STATUS) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_UNIT_ERASE : SPICMD_WRITE_STATUS failed.\n");
+		return 1;
+	}
+
+	/* enable write spi flash */
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_ENABLE);
+	if (rom_instruction_cycle(SPICMD_WRITE_ENABLE) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_UNIT_ERASE : SPICMD_WRITE_ENABLE failed.\n");
+		return 1;
+	}
+
+	return 0;
+}
+
+/* erase one block or chip or sector as needed */
+static int ec_unit_erase(unsigned char erase_cmd, unsigned int addr)
+{
+	unsigned char status;
+	int ret = 0, i = 0;
+	int unprotect_count = 3;
+	int check_flag = 0;
+
+	/* enable spicmd writing. */
+	ec_start_spi();
+
+#ifdef EC_ROM_PROTECTION
+	/* added for re-check SPICMD_READ_STATUS */
+	while (unprotect_count-- > 0) {
+		if (EC_ROM_unprotect()) {
+			ret = -EINVAL;
+			goto out;
+		}
+
+		/* first time:500ms --> 5.5sec -->10.5sec */
+		for (i = 0; i < ((2 - unprotect_count) * 100 + 10); i++)
+			udelay(50000);
+		ec_write(REG_XBISPICMD, SPICMD_READ_STATUS);
+		if (rom_instruction_cycle(SPICMD_READ_STATUS)
+				== EC_STATE_BUSY) {
+			printk(KERN_ERR
+			       "EC_PROGRAM_ROM : SPICMD_READ_STATUS failed.\n");
+		} else {
+			status = ec_read(REG_XBISPIDAT);
+			printk(KERN_INFO "Read unprotect status : 0x%x\n",
+				   status);
+			if ((status & 0x1C) == 0x00) {
+				printk(KERN_INFO
+					   "Read unprotect status OK1 : 0x%x\n",
+					   status & 0x1C);
+				check_flag = 1;
+				break;
+			}
+		}
+	}
+
+	if (!check_flag) {
+		printk(KERN_INFO "SPI ROM unprotect fail.\n");
+		return 1;
+	}
+#endif
+
+	/* block address fill */
+	if (erase_cmd == SPICMD_BLK_ERASE) {
+		ec_write(REG_XBISPIA2, (addr & 0x00ff0000) >> 16);
+		ec_write(REG_XBISPIA1, (addr & 0x0000ff00) >> 8);
+		ec_write(REG_XBISPIA0, (addr & 0x000000ff) >> 0);
+	}
+
+	/* erase the whole chip first */
+	ec_write(REG_XBISPICMD, erase_cmd);
+	if (rom_instruction_cycle(erase_cmd) == EC_STATE_BUSY) {
+		printk(KERN_ERR "EC_UNIT_ERASE : erase failed.\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+ out:
+	/* disable spicmd writing. */
+	ec_stop_spi();
+
+	return ret;
+}
+
+/* update the whole rom content with H/W mode
+ * PLEASE USING ec_unit_erase() FIRSTLY
+ */
+static int ec_program_rom(struct ec_info *info, int flag)
+{
+	unsigned int addr = 0;
+	unsigned long size = 0;
+	unsigned char *ptr = NULL;
+	unsigned char data;
+	unsigned char val = 0;
+	int ret = 0;
+	int i, j;
+	unsigned char status;
+
+	/* modify for program serial No.
+	 * set IE_START_ADDR & use idle mode,
+	 * disable WDD
+	 */
+	if (flag == PROGRAM_FLAG_ROM) {
+		ret = ec_init_reset_mode();
+		addr = info->start_addr + EC_START_ADDR;
+		printk(KERN_INFO "PROGRAM_FLAG_ROM..............\n");
+	} else if (flag == PROGRAM_FLAG_IE) {
+		ret = ec_init_idle_mode();
+		ec_disable_WDD();
+		addr = info->start_addr + IE_START_ADDR;
+		printk(KERN_INFO "PROGRAM_FLAG_IE..............\n");
+	} else {
+		return 0;
+	}
+
+	if (ret < 0) {
+		if (flag == PROGRAM_FLAG_IE)
+			ec_enable_WDD();
+		return ret;
+	}
+
+	size = info->size;
+	ptr = info->buf;
+	printk(KERN_INFO "starting update ec ROM..............\n");
+
+	ret = ec_unit_erase(SPICMD_BLK_ERASE, addr);
+	if (ret) {
+		printk(KERN_ERR "program ec : erase block failed.\n");
+		goto out;
+	}
+	printk(KERN_ERR "program ec : erase block OK.\n");
+
+	i = 0;
+	while (i < size) {
+		data = *(ptr + i);
+		ec_write_byte(addr, data);
+		ec_read_byte(addr, &val);
+		if (val != data) {
+			ec_write_byte(addr, data);
+			ec_read_byte(addr, &val);
+			if (val != data) {
+				printk(KERN_INFO
+				"EC : Second flash program failed at:\t");
+				printk(KERN_INFO
+				"addr : 0x%x, source : 0x%x, dest: 0x%x\n",
+				     addr, data, val);
+				printk(KERN_INFO "This should not happen... STOP\n");
+				break;
+			}
+		}
+		i++;
+		addr++;
+	}
+
+#ifdef	EC_ROM_PROTECTION
+	/* we should start spi access firstly */
+	ec_start_spi();
+
+	/* enable write spi flash */
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_ENABLE);
+	if (rom_instruction_cycle(SPICMD_WRITE_ENABLE) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_PROGRAM_ROM : SPICMD_WRITE_ENABLE failed.\n");
+		goto out1;
+	}
+
+	/* protect the status register of rom */
+	ec_write(REG_XBISPICMD, SPICMD_READ_STATUS);
+	if (rom_instruction_cycle(SPICMD_READ_STATUS) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_PROGRAM_ROM : SPICMD_READ_STATUS failed.\n");
+		goto out1;
+	}
+	status = ec_read(REG_XBISPIDAT);
+
+	ec_write(REG_XBISPIDAT, status | 0x1C);
+	if (ec_instruction_cycle() < 0) {
+		printk(KERN_ERR
+		       "EC_PROGRAM_ROM : write status value failed.\n");
+		goto out1;
+	}
+
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_STATUS);
+	if (rom_instruction_cycle(SPICMD_WRITE_STATUS) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_PROGRAM_ROM : SPICMD_WRITE_STATUS failed.\n");
+		goto out1;
+	}
+#endif
+
+	/* disable the write action to spi rom */
+	ec_write(REG_XBISPICMD, SPICMD_WRITE_DISABLE);
+	if (rom_instruction_cycle(SPICMD_WRITE_DISABLE) == EC_STATE_BUSY) {
+		printk(KERN_ERR
+		       "EC_PROGRAM_ROM : SPICMD_WRITE_DISABLE failed.\n");
+		goto out1;
+	}
+
+ out1:
+	/* we should stop spi access firstly */
+	ec_stop_spi();
+ out:
+	/* for security */
+	for (j = 0; j < 2000; j++)
+		udelay(1000);
+
+	/* modify for program serial No.
+	 * after program No exit idle mode
+	 * and enable WDD
+	 */
+	if (flag == PROGRAM_FLAG_ROM) {
+		/* exit from the reset mode */
+		ec_exit_reset_mode();
+	} else {
+		/* ec exit from idle mode */
+		ret = ec_exit_idle_mode();
+		ec_enable_WDD();
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/* ioctl  */
+static int misc_ioctl(struct inode *inode, struct file *filp, u_int cmd,
+		      u_long arg)
+{
+	struct ec_info ecinfo;
+	void __user *ptr = (void __user *)arg;
+	struct ec_reg *ecreg = (struct ec_reg *)(filp->private_data);
+	int ret = 0;
+
+	switch (cmd) {
+	case IOCTL_RDREG:
+		ret = copy_from_user(ecreg, ptr, sizeof(struct ec_reg));
+		if (ret) {
+			printk(KERN_ERR "reg read : copy from user error.\n");
+			return -EFAULT;
+		}
+		if ((ecreg->addr > EC_MAX_REGADDR)
+		    || (ecreg->addr < EC_MIN_REGADDR)) {
+			printk(KERN_ERR
+			       "reg read : out of register address range.\n");
+			return -EINVAL;
+		}
+		ecreg->val = ec_read(ecreg->addr);
+		ret = copy_to_user(ptr, ecreg, sizeof(struct ec_reg));
+		if (ret) {
+			printk(KERN_ERR "reg read : copy to user error.\n");
+			return -EFAULT;
+		}
+		break;
+	case IOCTL_WRREG:
+		ret = copy_from_user(ecreg, ptr, sizeof(struct ec_reg));
+		if (ret) {
+			printk(KERN_ERR "reg write : copy from user error.\n");
+			return -EFAULT;
+		}
+		if ((ecreg->addr > EC_MAX_REGADDR)
+		    || (ecreg->addr < EC_MIN_REGADDR)) {
+			printk(KERN_ERR
+			       "reg write : out of register address range.\n");
+			return -EINVAL;
+		}
+		ec_write(ecreg->addr, ecreg->val);
+		break;
+	case IOCTL_READ_EC:
+		ret = copy_from_user(ecreg, ptr, sizeof(struct ec_reg));
+		if (ret) {
+			printk(KERN_ERR "spi read : copy from user error.\n");
+			return -EFAULT;
+		}
+		if ((ecreg->addr > EC_RAM_ADDR)
+		    && (ecreg->addr < EC_MAX_REGADDR)) {
+			printk(KERN_ERR
+			       "spi read : out of register address range.\n");
+			return -EINVAL;
+		}
+		ec_read_byte(ecreg->addr, &(ecreg->val));
+		ret = copy_to_user(ptr, ecreg, sizeof(struct ec_reg));
+		if (ret) {
+			printk(KERN_ERR "spi read : copy to user error.\n");
+			return -EFAULT;
+		}
+		break;
+	case IOCTL_PROGRAM_IE:
+		ecinfo.start_addr = EC_START_ADDR;
+		ecinfo.size = EC_CONTENT_MAX_SIZE;
+		ecinfo.buf = (u8 *) kmalloc(ecinfo.size, GFP_KERNEL);
+		if (ecinfo.buf == NULL) {
+			printk(KERN_ERR "program ie : kmalloc failed.\n");
+			return -ENOMEM;
+		}
+		ret = copy_from_user(ecinfo.buf, (u8 *) ptr, ecinfo.size);
+		if (ret) {
+			printk(KERN_ERR "program ie : copy from user error.\n");
+			kfree(ecinfo.buf);
+			ecinfo.buf = NULL;
+			return -EFAULT;
+		}
+
+		/* use ec_program_rom to write serial No */
+		ec_program_rom(&ecinfo, PROGRAM_FLAG_IE);
+
+		kfree(ecinfo.buf);
+		ecinfo.buf = NULL;
+		break;
+	case IOCTL_PROGRAM_EC:
+		ecinfo.start_addr = EC_START_ADDR;
+		if (get_user((ecinfo.size), (u32 *) ptr)) {
+			printk(KERN_ERR "program ec : get user error.\n");
+			return -EFAULT;
+		}
+		if ((ecinfo.size) > EC_CONTENT_MAX_SIZE) {
+			printk(KERN_ERR "program ec : size out of limited.\n");
+			return -EINVAL;
+		}
+		ecinfo.buf = (u8 *) kmalloc(ecinfo.size, GFP_KERNEL);
+		if (ecinfo.buf == NULL) {
+			printk(KERN_ERR "program ec : kmalloc failed.\n");
+			return -ENOMEM;
+		}
+		ret = copy_from_user(ecinfo.buf, ((u8 *) ptr + 4), ecinfo.size);
+		if (ret) {
+			printk(KERN_ERR "program ec : copy from user error.\n");
+			kfree(ecinfo.buf);
+			ecinfo.buf = NULL;
+			return -EFAULT;
+		}
+
+		ec_program_rom(&ecinfo, PROGRAM_FLAG_ROM);
+
+		kfree(ecinfo.buf);
+		ecinfo.buf = NULL;
+		break;
+
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+static long misc_compat_ioctl(struct file *file, unsigned int cmd,
+			      unsigned long arg)
+{
+	return misc_ioctl(file->f_dentry->d_inode, file, cmd, arg);
+}
+
+static int misc_open(struct inode *inode, struct file *filp)
+{
+	struct ec_reg *ecreg = NULL;
+	ecreg = kmalloc(sizeof(struct ec_reg), GFP_KERNEL);
+	if (ecreg)
+		filp->private_data = ecreg;
+
+	return ecreg ? 0 : -ENOMEM;
+}
+
+static int misc_release(struct inode *inode, struct file *filp)
+{
+	struct ec_reg *ecreg = (struct ec_reg *)(filp->private_data);
+
+	filp->private_data = NULL;
+	kfree(ecreg);
+
+	return 0;
+}
+
+static const struct file_operations ecmisc_fops = {
+	.open = misc_open,
+	.release = misc_release,
+	.read = NULL,
+	.write = NULL,
+#ifdef	CONFIG_64BIT
+	.compat_ioctl = misc_compat_ioctl,
+#else
+	.ioctl = misc_ioctl,
+#endif
+};
+
+static struct miscdevice ecmisc_device = {
+	.minor = MISC_DYNAMIC_MINOR,
+	.name = EC_MISC_DEV,
+	.fops = &ecmisc_fops
+};
+
+static int __init ecmisc_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "EC misc device init.\n");
+	ret = misc_register(&ecmisc_device);
+
+	return ret;
+}
+
+static void __exit ecmisc_exit(void)
+{
+	printk(KERN_INFO "EC misc device exit.\n");
+	misc_deregister(&ecmisc_device);
+}
+
+module_init(ecmisc_init);
+module_exit(ecmisc_exit);
+
+MODULE_AUTHOR("liujl <liujl@lemote.com>");
+MODULE_DESCRIPTION("Driver for flushing/dumping ROM of EC on YeeLoong laptop");
+MODULE_LICENSE("GPL");
diff -Nur linux-2.6.36.orig/drivers/platform/mips/yeeloong_laptop.c linux-2.6.36/drivers/platform/mips/yeeloong_laptop.c
--- linux-2.6.36.orig/drivers/platform/mips/yeeloong_laptop.c	1970-01-01 01:00:00.000000000 +0100
+++ linux-2.6.36/drivers/platform/mips/yeeloong_laptop.c	2010-11-18 11:47:59.000000000 +0100
@@ -0,0 +1,1200 @@
+/*
+ * Driver for YeeLoong laptop extras
+ *
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>, Liu Junliang <liujl@lemote.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License version 2 as
+ *  published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/backlight.h>	/* for backlight subdriver */
+#include <linux/fb.h>
+#include <linux/hwmon.h>	/* for hwmon subdriver */
+#include <linux/hwmon-sysfs.h>
+#include <linux/video_output.h>	/* for video output subdriver */
+#include <linux/input.h>	/* for hotkey subdriver */
+#include <linux/input/sparse-keymap.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/power_supply.h>	/* for AC & Battery subdriver */
+
+#include <cs5536/cs5536.h>
+
+#include <loongson.h>		/* for loongson_cmdline */
+#include <ec_kb3310b.h>
+
+/* common function */
+#define EC_VER_LEN 64
+
+static int ec_version_before(char *version)
+{
+	char *p, ec_ver[EC_VER_LEN];
+
+	p = strstr(loongson_cmdline, "EC_VER=");
+	if (!p)
+		memset(ec_ver, 0, EC_VER_LEN);
+	else {
+		strncpy(ec_ver, p, EC_VER_LEN);
+		p = strstr(ec_ver, " ");
+		if (p)
+			*p = '\0';
+	}
+
+	return (strncasecmp(ec_ver, version, 64) < 0);
+}
+
+/* backlight subdriver */
+#define MAX_BRIGHTNESS	8
+
+static int yeeloong_set_brightness(struct backlight_device *bd)
+{
+	unsigned int level, current_level;
+	static unsigned int old_level;
+
+	level = (bd->props.fb_blank == FB_BLANK_UNBLANK &&
+		 bd->props.power == FB_BLANK_UNBLANK) ?
+	    bd->props.brightness : 0;
+
+	level = SENSORS_LIMIT(level, 0, MAX_BRIGHTNESS);
+
+	/* Avoid to modify the brightness when EC is tuning it */
+	if (old_level != level) {
+		current_level = ec_read(REG_DISPLAY_BRIGHTNESS);
+		if (old_level == current_level)
+			ec_write(REG_DISPLAY_BRIGHTNESS, level);
+		old_level = level;
+	}
+
+	return 0;
+}
+
+static int yeeloong_get_brightness(struct backlight_device *bd)
+{
+	return ec_read(REG_DISPLAY_BRIGHTNESS);
+}
+
+static struct backlight_ops backlight_ops = {
+	.get_brightness = yeeloong_get_brightness,
+	.update_status = yeeloong_set_brightness,
+};
+
+static struct backlight_device *yeeloong_backlight_dev;
+
+static int yeeloong_backlight_init(void)
+{
+	int ret;
+	struct backlight_properties props;
+
+	memset(&props, 0, sizeof(struct backlight_properties));
+	props.max_brightness = MAX_BRIGHTNESS;
+	yeeloong_backlight_dev = backlight_device_register("backlight0", NULL,
+			NULL, &backlight_ops, &props);
+
+	if (IS_ERR(yeeloong_backlight_dev)) {
+		ret = PTR_ERR(yeeloong_backlight_dev);
+		yeeloong_backlight_dev = NULL;
+		return ret;
+	}
+
+	yeeloong_backlight_dev->props.brightness =
+		yeeloong_get_brightness(yeeloong_backlight_dev);
+	backlight_update_status(yeeloong_backlight_dev);
+
+	return 0;
+}
+
+static void yeeloong_backlight_exit(void)
+{
+	if (yeeloong_backlight_dev) {
+		backlight_device_unregister(yeeloong_backlight_dev);
+		yeeloong_backlight_dev = NULL;
+	}
+}
+
+/* AC & Battery subdriver */
+
+static struct power_supply yeeloong_ac, yeeloong_bat;
+
+#define AC_OFFLINE          0
+#define AC_ONLINE           1
+
+static int yeeloong_get_ac_props(struct power_supply *psy,
+				enum power_supply_property psp,
+				union power_supply_propval *val)
+{
+	switch (psp) {
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = ((ec_read(REG_BAT_POWER)) & BIT_BAT_POWER_ACIN) ?
+			AC_ONLINE : AC_OFFLINE;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property yeeloong_ac_props[] = {
+	POWER_SUPPLY_PROP_ONLINE,
+};
+
+static struct power_supply yeeloong_ac = {
+	.name = "yeeloong-ac",
+	.type = POWER_SUPPLY_TYPE_MAINS,
+	.properties = yeeloong_ac_props,
+	.num_properties = ARRAY_SIZE(yeeloong_ac_props),
+	.get_property = yeeloong_get_ac_props,
+};
+
+#define BAT_CAP_CRITICAL 5
+#define BAT_CAP_HIGH     99
+
+#define get_bat_info(type) \
+	((ec_read(REG_BAT_##type##_HIGH) << 8) | \
+	 (ec_read(REG_BAT_##type##_LOW)))
+
+static int yeeloong_bat_get_ex_property(enum power_supply_property psp,
+				     union power_supply_propval *val)
+{
+	int bat_in, curr_cap, cap_level, status, charge, health;
+
+	status = ec_read(REG_BAT_STATUS);
+	bat_in = status & BIT_BAT_STATUS_IN;
+	curr_cap = get_bat_info(RELATIVE_CAP);
+	if (status & BIT_BAT_STATUS_FULL)
+		curr_cap = 100;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = bat_in;
+		break;
+	case POWER_SUPPLY_PROP_CAPACITY:
+		val->intval = curr_cap;
+		break;
+	case POWER_SUPPLY_PROP_CAPACITY_LEVEL:
+		cap_level = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL;
+		if (status & BIT_BAT_STATUS_LOW) {
+			cap_level = POWER_SUPPLY_CAPACITY_LEVEL_LOW;
+			if (curr_cap <= BAT_CAP_CRITICAL)
+				cap_level =
+					POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL;
+		} else if (status & BIT_BAT_STATUS_FULL) {
+			cap_level = POWER_SUPPLY_CAPACITY_LEVEL_FULL;
+			if (curr_cap >= BAT_CAP_HIGH)
+				cap_level = POWER_SUPPLY_CAPACITY_LEVEL_HIGH;
+		} else if (status & BIT_BAT_STATUS_DESTROY)
+			cap_level = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN;
+		val->intval = cap_level;
+		break;
+	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW:
+		/* seconds */
+		val->intval = bat_in ? (curr_cap - 3) * 54 + 142 : 0;
+		break;
+	case POWER_SUPPLY_PROP_STATUS:
+		if (!bat_in)
+			charge = POWER_SUPPLY_STATUS_UNKNOWN;
+		else {
+			if (status & BIT_BAT_STATUS_FULL) {
+				val->intval = POWER_SUPPLY_STATUS_FULL;
+				break;
+			}
+
+			charge = ec_read(REG_BAT_CHARGE);
+			if (charge & FLAG_BAT_CHARGE_DISCHARGE)
+				charge = POWER_SUPPLY_STATUS_DISCHARGING;
+			else if (charge & FLAG_BAT_CHARGE_CHARGE)
+				charge = POWER_SUPPLY_STATUS_CHARGING;
+			else
+				charge = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		}
+		val->intval = charge;
+		break;
+	case POWER_SUPPLY_PROP_HEALTH:
+		if (!bat_in) /* no battery present */
+			health = POWER_SUPPLY_HEALTH_UNKNOWN;
+		else { /* Assume it is good */
+			health = POWER_SUPPLY_HEALTH_GOOD;
+			if (status &
+				(BIT_BAT_STATUS_DESTROY | BIT_BAT_STATUS_LOW))
+				health = POWER_SUPPLY_HEALTH_DEAD;
+			if (ec_read(REG_BAT_CHARGE_STATUS) &
+				BIT_BAT_CHARGE_STATUS_OVERTEMP)
+				health = POWER_SUPPLY_HEALTH_OVERHEAT;
+		}
+		val->intval = health;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_NOW:	/* 1/100(%)*1000 µAh */
+		val->intval = curr_cap * get_bat_info(FULLCHG_CAP) * 10;
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static int get_battery_temp(void)
+{
+	int value;
+
+	value = get_bat_info(TEMPERATURE);
+
+	return value * 1000;
+}
+
+static int get_battery_current(void)
+{
+	s16 value;
+
+	value = get_bat_info(CURRENT);
+
+	return -value;
+}
+
+static int get_battery_voltage(void)
+{
+	int value;
+
+	value = get_bat_info(VOLTAGE);
+
+	return value;
+}
+
+static int yeeloong_get_bat_props(struct power_supply *psy,
+				     enum power_supply_property psp,
+				     union power_supply_propval *val)
+{
+	switch (psp) {
+	/* Fixed information */
+	case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
+		val->intval = get_bat_info(DESIGN_VOL) * 1000;	/* mV -> µV */
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
+		val->intval = get_bat_info(DESIGN_CAP) * 1000;	/* mAh->µAh */
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL:
+		val->intval = get_bat_info(FULLCHG_CAP) * 1000;	/* µAh */
+		break;
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = (ec_read(REG_BAT_VENDOR) ==
+				FLAG_BAT_VENDOR_SANYO) ? "SANYO" : "SIMPLO";
+		break;
+	/* Dynamic information */
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		val->intval = get_battery_current() * 1000;	/* mA -> µA */
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		val->intval = get_battery_voltage() * 1000;	/* mV -> µV */
+		break;
+	case POWER_SUPPLY_PROP_TEMP:
+		val->intval = get_battery_temp();	/* Celcius */
+		break;
+	/* Dynamic but related information */
+	default:
+		return yeeloong_bat_get_ex_property(psp, val);
+	}
+
+	return 0;
+}
+
+static enum power_supply_property yeeloong_bat_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW,
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CAPACITY_LEVEL,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static struct power_supply yeeloong_bat = {
+	.name = "yeeloong-bat",
+	.type = POWER_SUPPLY_TYPE_BATTERY,
+	.properties = yeeloong_bat_props,
+	.num_properties = ARRAY_SIZE(yeeloong_bat_props),
+	.get_property = yeeloong_get_bat_props,
+};
+
+static int ac_bat_initialized;
+
+static int yeeloong_bat_init(void)
+{
+	int ret;
+
+	ret = power_supply_register(NULL, &yeeloong_ac);
+	if (ret)
+		return ret;
+	ret = power_supply_register(NULL, &yeeloong_bat);
+	if (ret) {
+		power_supply_unregister(&yeeloong_ac);
+		return ret;
+	}
+	ac_bat_initialized = 1;
+
+	return 0;
+}
+
+static void yeeloong_bat_exit(void)
+{
+	ac_bat_initialized = 0;
+
+	power_supply_unregister(&yeeloong_ac);
+	power_supply_unregister(&yeeloong_bat);
+}
+/* hwmon subdriver */
+
+#define MIN_FAN_SPEED 0
+#define MAX_FAN_SPEED 3
+
+static int get_fan_pwm_enable(void)
+{
+	int level, mode;
+
+	level = ec_read(REG_FAN_SPEED_LEVEL);
+	mode = ec_read(REG_FAN_AUTO_MAN_SWITCH);
+
+	if (level == MAX_FAN_SPEED && mode == BIT_FAN_MANUAL)
+		mode = 0;
+	else if (mode == BIT_FAN_MANUAL)
+		mode = 1;
+	else
+		mode = 2;
+
+	return mode;
+}
+
+static void set_fan_pwm_enable(int mode)
+{
+	switch (mode) {
+	case 0:
+		/* fullspeed */
+		ec_write(REG_FAN_AUTO_MAN_SWITCH, BIT_FAN_MANUAL);
+		ec_write(REG_FAN_SPEED_LEVEL, MAX_FAN_SPEED);
+		break;
+	case 1:
+		ec_write(REG_FAN_AUTO_MAN_SWITCH, BIT_FAN_MANUAL);
+		break;
+	case 2:
+		ec_write(REG_FAN_AUTO_MAN_SWITCH, BIT_FAN_AUTO);
+		break;
+	default:
+		break;
+	}
+}
+
+static int get_fan_pwm(void)
+{
+	return ec_read(REG_FAN_SPEED_LEVEL);
+}
+
+static void set_fan_pwm(int value)
+{
+	int mode;
+
+	mode = ec_read(REG_FAN_AUTO_MAN_SWITCH);
+	if (mode != BIT_FAN_MANUAL)
+		return;
+
+	value = SENSORS_LIMIT(value, 0, 3);
+
+	/* We must ensure the fan is on */
+	if (value > 0)
+		ec_write(REG_FAN_CONTROL, BIT_FAN_CONTROL_ON);
+
+	ec_write(REG_FAN_SPEED_LEVEL, value);
+}
+
+static int get_fan_rpm(void)
+{
+	int value;
+
+	value = FAN_SPEED_DIVIDER /
+	    (((ec_read(REG_FAN_SPEED_HIGH) & 0x0f) << 8) |
+	     ec_read(REG_FAN_SPEED_LOW));
+
+	return value;
+}
+
+static int get_cpu_temp(void)
+{
+	s8 value;
+
+	value = ec_read(REG_TEMPERATURE_VALUE);
+
+	return value * 1000;
+}
+
+static int get_cpu_temp_max(void)
+{
+	return 60 * 1000;
+}
+
+static int get_battery_temp_alarm(void)
+{
+	int status;
+
+	status = (ec_read(REG_BAT_CHARGE_STATUS) &
+			BIT_BAT_CHARGE_STATUS_OVERTEMP);
+
+	return !!status;
+}
+
+static ssize_t store_sys_hwmon(void (*set) (int), const char *buf, size_t count)
+{
+	int ret;
+	unsigned long value;
+
+	if (!count)
+		return 0;
+
+	ret = strict_strtoul(buf, 10, &value);
+	if (ret)
+		return ret;
+
+	set(value);
+
+	return count;
+}
+
+static ssize_t show_sys_hwmon(int (*get) (void), char *buf)
+{
+	return sprintf(buf, "%d\n", get());
+}
+
+#define CREATE_SENSOR_ATTR(_name, _mode, _set, _get)		\
+	static ssize_t show_##_name(struct device *dev,			\
+				    struct device_attribute *attr,	\
+				    char *buf)				\
+	{								\
+		return show_sys_hwmon(_set, buf);			\
+	}								\
+	static ssize_t store_##_name(struct device *dev,		\
+				     struct device_attribute *attr,	\
+				     const char *buf, size_t count)	\
+	{								\
+		return store_sys_hwmon(_get, buf, count);		\
+	}								\
+	static SENSOR_DEVICE_ATTR(_name, _mode, show_##_name, store_##_name, 0);
+
+CREATE_SENSOR_ATTR(fan1_input, S_IRUGO, get_fan_rpm, NULL);
+CREATE_SENSOR_ATTR(pwm1, S_IRUGO | S_IWUSR, get_fan_pwm, set_fan_pwm);
+CREATE_SENSOR_ATTR(pwm1_enable, S_IRUGO | S_IWUSR, get_fan_pwm_enable,
+		set_fan_pwm_enable);
+CREATE_SENSOR_ATTR(temp1_input, S_IRUGO, get_cpu_temp, NULL);
+CREATE_SENSOR_ATTR(temp1_max, S_IRUGO, get_cpu_temp_max, NULL);
+CREATE_SENSOR_ATTR(temp2_input, S_IRUGO, get_battery_temp, NULL);
+CREATE_SENSOR_ATTR(temp2_max_alarm, S_IRUGO, get_battery_temp_alarm, NULL);
+CREATE_SENSOR_ATTR(curr1_input, S_IRUGO, get_battery_current, NULL);
+CREATE_SENSOR_ATTR(in1_input, S_IRUGO, get_battery_voltage, NULL);
+
+static ssize_t
+show_name(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	return sprintf(buf, "yeeloong\n");
+}
+
+static SENSOR_DEVICE_ATTR(name, S_IRUGO, show_name, NULL, 0);
+
+static struct attribute *hwmon_attributes[] = {
+	&sensor_dev_attr_pwm1.dev_attr.attr,
+	&sensor_dev_attr_pwm1_enable.dev_attr.attr,
+	&sensor_dev_attr_fan1_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	&sensor_dev_attr_temp1_max.dev_attr.attr,
+	&sensor_dev_attr_temp2_input.dev_attr.attr,
+	&sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
+	&sensor_dev_attr_curr1_input.dev_attr.attr,
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_name.dev_attr.attr,
+	NULL
+};
+
+static struct attribute_group hwmon_attribute_group = {
+	.attrs = hwmon_attributes
+};
+
+static struct device *yeeloong_hwmon_dev;
+
+static int yeeloong_hwmon_init(void)
+{
+	int ret;
+
+	yeeloong_hwmon_dev = hwmon_device_register(NULL);
+	if (IS_ERR(yeeloong_hwmon_dev)) {
+		pr_err("Fail to register yeeloong hwmon device\n");
+		yeeloong_hwmon_dev = NULL;
+		return PTR_ERR(yeeloong_hwmon_dev);
+	}
+	ret = sysfs_create_group(&yeeloong_hwmon_dev->kobj,
+				 &hwmon_attribute_group);
+	if (ret) {
+		hwmon_device_unregister(yeeloong_hwmon_dev);
+		yeeloong_hwmon_dev = NULL;
+		return ret;
+	}
+	/* ensure fan is set to auto mode */
+	set_fan_pwm_enable(2);
+
+	return 0;
+}
+
+static void yeeloong_hwmon_exit(void)
+{
+	if (yeeloong_hwmon_dev) {
+		sysfs_remove_group(&yeeloong_hwmon_dev->kobj,
+				   &hwmon_attribute_group);
+		hwmon_device_unregister(yeeloong_hwmon_dev);
+		yeeloong_hwmon_dev = NULL;
+	}
+}
+
+/* video output subdriver */
+
+static int lcd_video_output_get(struct output_device *od)
+{
+	return ec_read(REG_DISPLAY_LCD);
+}
+
+#define LCD	0
+#define CRT	1
+
+static void display_vo_set(int display, int on)
+{
+	int addr;
+	unsigned long value;
+
+	addr = (display == LCD) ? 0x31 : 0x21;
+
+	outb(addr, 0x3c4);
+	value = inb(0x3c5);
+
+	if (display == LCD)
+		value |= (on ? 0x03 : 0x02);
+	else {
+		if (on)
+			clear_bit(7, &value);
+		else
+			set_bit(7, &value);
+	}
+
+	outb(addr, 0x3c4);
+	outb(value, 0x3c5);
+}
+
+static int lcd_video_output_set(struct output_device *od)
+{
+	unsigned long status;
+
+	status = !!od->request_state;
+
+	display_vo_set(LCD, status);
+	ec_write(REG_BACKLIGHT_CTRL, status);
+
+	return 0;
+}
+
+static struct output_properties lcd_output_properties = {
+	.set_state = lcd_video_output_set,
+	.get_status = lcd_video_output_get,
+};
+
+static int crt_video_output_get(struct output_device *od)
+{
+	return ec_read(REG_CRT_DETECT);
+}
+
+static int crt_video_output_set(struct output_device *od)
+{
+	unsigned long status;
+
+	status = !!od->request_state;
+
+	if (ec_read(REG_CRT_DETECT) == BIT_CRT_DETECT_PLUG)
+		display_vo_set(CRT, status);
+
+	return 0;
+}
+
+static struct output_properties crt_output_properties = {
+	.set_state = crt_video_output_set,
+	.get_status = crt_video_output_get,
+};
+
+static struct output_device *lcd_output_dev, *crt_output_dev;
+
+static void yeeloong_lcd_vo_set(int status)
+{
+	lcd_output_dev->request_state = status;
+	lcd_video_output_set(lcd_output_dev);
+}
+
+static void yeeloong_crt_vo_set(int status)
+{
+	crt_output_dev->request_state = status;
+	crt_video_output_set(crt_output_dev);
+}
+
+static int yeeloong_vo_init(void)
+{
+	int ret;
+
+	/* Register video output device: lcd, crt */
+	lcd_output_dev = video_output_register("LCD", NULL, NULL,
+			&lcd_output_properties);
+
+	if (IS_ERR(lcd_output_dev)) {
+		ret = PTR_ERR(lcd_output_dev);
+		lcd_output_dev = NULL;
+		return ret;
+	}
+	/* Ensure LCD is on by default */
+	yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+
+	crt_output_dev = video_output_register("CRT", NULL, NULL,
+			&crt_output_properties);
+
+	if (IS_ERR(crt_output_dev)) {
+		ret = PTR_ERR(crt_output_dev);
+		crt_output_dev = NULL;
+		return ret;
+	}
+
+	/* Turn off CRT by default, and will be enabled when the CRT
+	 * connectting event reported by SCI */
+	yeeloong_crt_vo_set(BIT_CRT_DETECT_UNPLUG);
+
+	return 0;
+}
+
+static void yeeloong_vo_exit(void)
+{
+	if (lcd_output_dev) {
+		video_output_unregister(lcd_output_dev);
+		lcd_output_dev = NULL;
+	}
+	if (crt_output_dev) {
+		video_output_unregister(crt_output_dev);
+		crt_output_dev = NULL;
+	}
+}
+
+/* hotkey subdriver */
+
+static struct input_dev *yeeloong_hotkey_dev;
+
+static const struct key_entry yeeloong_keymap[] = {
+	{KE_SW, EVENT_LID, { SW_LID } },
+	{KE_KEY, EVENT_CAMERA, { KEY_CAMERA } }, /* Fn + ESC */
+	{KE_KEY, EVENT_SLEEP, { KEY_SLEEP } }, /* Fn + F1 */
+	{KE_KEY, EVENT_DISPLAYTOGGLE, { KEY_DISPLAYTOGGLE } }, /* Fn + F2 */
+	{KE_KEY, EVENT_SWITCHVIDEOMODE, { KEY_SWITCHVIDEOMODE } }, /* Fn + F3 */
+	{KE_KEY, EVENT_AUDIO_MUTE, { KEY_MUTE } }, /* Fn + F4 */
+	{KE_KEY, EVENT_WLAN, { KEY_WLAN } }, /* Fn + F5 */
+	{KE_KEY, EVENT_DISPLAY_BRIGHTNESS, { KEY_BRIGHTNESSUP } }, /* Fn + up */
+	{KE_KEY, EVENT_DISPLAY_BRIGHTNESS, { KEY_BRIGHTNESSDOWN } }, /* Fn + down */
+	{KE_KEY, EVENT_AUDIO_VOLUME, { KEY_VOLUMEUP } }, /* Fn + right */
+	{KE_KEY, EVENT_AUDIO_VOLUME, { KEY_VOLUMEDOWN } }, /* Fn + left */
+	{KE_END, 0}
+};
+
+static struct key_entry *get_event_key_entry(int event, int status)
+{
+	struct key_entry *ke;
+	static int old_brightness_status = -1;
+	static int old_volume_status = -1;
+
+	ke = sparse_keymap_entry_from_scancode(yeeloong_hotkey_dev, event);
+	if (!ke)
+		return NULL;
+
+	switch (event) {
+	case EVENT_DISPLAY_BRIGHTNESS:
+		/* current status > old one, means up */
+		if ((status < old_brightness_status) || (0 == status))
+			ke++;
+		old_brightness_status = status;
+		break;
+	case EVENT_AUDIO_VOLUME:
+		if ((status < old_volume_status) || (0 == status))
+			ke++;
+		old_volume_status = status;
+		break;
+	default:
+		break;
+	}
+
+	return ke;
+}
+
+static int report_lid_switch(int status)
+{
+	input_report_switch(yeeloong_hotkey_dev, SW_LID, !status);
+	input_sync(yeeloong_hotkey_dev);
+
+	return status;
+}
+
+static int crt_detect_handler(int status)
+{
+	if (status) {
+		yeeloong_crt_vo_set(BIT_CRT_DETECT_PLUG);
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_OFF);
+	} else {
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+		yeeloong_crt_vo_set(BIT_CRT_DETECT_UNPLUG);
+	}
+	return status;
+}
+
+static int displaytoggle_handler(int status)
+{
+	/* EC(>=PQ1D26) does this job for us, we can not do it again,
+	 * otherwise, the brightness will not resume to the normal level! */
+	if (ec_version_before("EC_VER=PQ1D26"))
+		yeeloong_lcd_vo_set(status);
+
+	return status;
+}
+
+static int switchvideomode_handler(int status)
+{
+	static int video_output_status;
+
+	/* Only enable switch video output button
+	 * when CRT is connected */
+	if (ec_read(REG_CRT_DETECT) == BIT_CRT_DETECT_UNPLUG)
+		return 0;
+	/* 0. no CRT connected: LCD on, CRT off
+	 * 1. BOTH on
+	 * 2. LCD off, CRT on
+	 * 3. BOTH off
+	 * 4. LCD on, CRT off
+	 */
+	video_output_status++;
+	if (video_output_status > 4)
+		video_output_status = 1;
+
+	switch (video_output_status) {
+	case 1:
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+		yeeloong_crt_vo_set(BIT_CRT_DETECT_PLUG);
+		break;
+	case 2:
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_OFF);
+		yeeloong_crt_vo_set(BIT_CRT_DETECT_PLUG);
+		break;
+	case 3:
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_OFF);
+		yeeloong_crt_vo_set(BIT_CRT_DETECT_UNPLUG);
+		break;
+	case 4:
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+		yeeloong_crt_vo_set(BIT_CRT_DETECT_UNPLUG);
+		break;
+	default:
+		/* Ensure LCD is on */
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+		break;
+	}
+	return video_output_status;
+}
+
+static int camera_handler(int status)
+{
+	int value;
+
+	value = ec_read(REG_CAMERA_CONTROL);
+	ec_write(REG_CAMERA_CONTROL, value | (1 << 1));
+
+	return status;
+}
+
+static int usb2_handler(int status)
+{
+	pr_emerg("USB2 Over Current occurred\n");
+
+	return status;
+}
+
+static int usb0_handler(int status)
+{
+	pr_emerg("USB0 Over Current occurred\n");
+
+	return status;
+}
+
+static int ac_bat_handler(int status)
+{
+	if (ac_bat_initialized) {
+		power_supply_changed(&yeeloong_ac);
+		power_supply_changed(&yeeloong_bat);
+	}
+	return status;
+}
+
+static void do_event_action(int event)
+{
+	sci_handler handler;
+	int reg, status;
+	struct key_entry *ke;
+
+	reg = 0;
+	handler = NULL;
+
+	switch (event) {
+	case EVENT_LID:
+		reg = REG_LID_DETECT;
+		break;
+	case EVENT_SWITCHVIDEOMODE:
+		handler = switchvideomode_handler;
+		break;
+	case EVENT_CRT_DETECT:
+		reg = REG_CRT_DETECT;
+		handler = crt_detect_handler;
+		break;
+	case EVENT_CAMERA:
+		reg = REG_CAMERA_STATUS;
+		handler = camera_handler;
+		break;
+	case EVENT_USB_OC2:
+		reg = REG_USB2_FLAG;
+		handler = usb2_handler;
+		break;
+	case EVENT_USB_OC0:
+		reg = REG_USB0_FLAG;
+		handler = usb0_handler;
+		break;
+	case EVENT_DISPLAYTOGGLE:
+		reg = REG_DISPLAY_LCD;
+		handler = displaytoggle_handler;
+		break;
+	case EVENT_AUDIO_MUTE:
+		reg = REG_AUDIO_MUTE;
+		break;
+	case EVENT_DISPLAY_BRIGHTNESS:
+		reg = REG_DISPLAY_BRIGHTNESS;
+		break;
+	case EVENT_AUDIO_VOLUME:
+		reg = REG_AUDIO_VOLUME;
+		break;
+	case EVENT_AC_BAT:
+		handler = ac_bat_handler;
+		break;
+	default:
+		break;
+	}
+
+	if (reg != 0)
+		status = ec_read(reg);
+
+	if (handler != NULL)
+		status = handler(status);
+
+	pr_info("%s: event: %d status: %d\n", __func__, event, status);
+
+	/* Report current key to user-space */
+	ke = get_event_key_entry(event, status);
+	if (ke) {
+		if (ke->keycode == SW_LID)
+			report_lid_switch(status);
+		else
+			sparse_keymap_report_entry(yeeloong_hotkey_dev, ke, 1,
+					true);
+	}
+}
+
+/*
+ * SCI(system control interrupt) main interrupt routine
+ *
+ * We will do the query and get event number together so the interrupt routine
+ * should be longer than 120us now at least 3ms elpase for it.
+ */
+static irqreturn_t sci_irq_handler(int irq, void *dev_id)
+{
+	int ret, event;
+
+	if (SCI_IRQ_NUM != irq)
+		return IRQ_NONE;
+
+	/* Query the event number */
+	ret = ec_query_event_num();
+	if (ret < 0)
+		return IRQ_NONE;
+
+	event = ec_get_event_num();
+	if (event < EVENT_START || event > EVENT_END)
+		return IRQ_NONE;
+
+	/* Execute corresponding actions */
+	do_event_action(event);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Config and init some msr and gpio register properly.
+ */
+static int sci_irq_init(void)
+{
+	u32 hi, lo;
+	u32 gpio_base;
+	unsigned long flags;
+	int ret;
+
+	/* Get gpio base */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
+	gpio_base = lo & 0xff00;
+
+	/* Filter the former kb3310 interrupt for security */
+	ret = ec_query_event_num();
+	if (ret)
+		return ret;
+
+	/* For filtering next number interrupt */
+	udelay(10000);
+
+	/* Set gpio native registers and msrs for GPIO27 SCI EVENT PIN
+	 * gpio :
+	 *      input, pull-up, no-invert, event-count and value 0,
+	 *      no-filter, no edge mode
+	 *      gpio27 map to Virtual gpio0
+	 * msr :
+	 *      no primary and lpc
+	 *      Unrestricted Z input to IG10 from Virtual gpio 0.
+	 */
+	local_irq_save(flags);
+	_rdmsr(0x80000024, &hi, &lo);
+	lo &= ~(1 << 10);
+	_wrmsr(0x80000024, hi, lo);
+	_rdmsr(0x80000025, &hi, &lo);
+	lo &= ~(1 << 10);
+	_wrmsr(0x80000025, hi, lo);
+	_rdmsr(0x80000023, &hi, &lo);
+	lo |= (0x0a << 0);
+	_wrmsr(0x80000023, hi, lo);
+	local_irq_restore(flags);
+
+	/* Set gpio27 as sci interrupt
+	 *
+	 * input, pull-up, no-fliter, no-negedge, invert
+	 * the sci event is just about 120us
+	 */
+	asm(".set noreorder\n");
+	/*  input enable */
+	outl(0x00000800, (gpio_base | 0xA0));
+	/*  revert the input */
+	outl(0x00000800, (gpio_base | 0xA4));
+	/*  event-int enable */
+	outl(0x00000800, (gpio_base | 0xB8));
+	asm(".set reorder\n");
+
+	return 0;
+}
+
+static struct irqaction sci_irqaction = {
+	.handler = sci_irq_handler,
+	.name = "sci",
+	.flags = IRQF_SHARED,
+};
+
+static int yeeloong_hotkey_init(void)
+{
+	int ret;
+
+	ret = sci_irq_init();
+	if (ret)
+		return -EFAULT;
+
+	ret = setup_irq(SCI_IRQ_NUM, &sci_irqaction);
+	if (ret)
+		return -EFAULT;
+
+	yeeloong_hotkey_dev = input_allocate_device();
+
+	if (!yeeloong_hotkey_dev) {
+		remove_irq(SCI_IRQ_NUM, &sci_irqaction);
+		return -ENOMEM;
+	}
+
+	yeeloong_hotkey_dev->name = "HotKeys";
+	yeeloong_hotkey_dev->phys = "button/input0";
+	yeeloong_hotkey_dev->id.bustype = BUS_HOST;
+	yeeloong_hotkey_dev->dev.parent = NULL;
+
+	ret = sparse_keymap_setup(yeeloong_hotkey_dev, yeeloong_keymap, NULL);
+	if (ret) {
+		pr_err("Fail to setup input device keymap\n");
+		input_free_device(yeeloong_hotkey_dev);
+		return ret;
+	}
+
+	ret = input_register_device(yeeloong_hotkey_dev);
+	if (ret) {
+		sparse_keymap_free(yeeloong_hotkey_dev);
+		input_free_device(yeeloong_hotkey_dev);
+		return ret;
+	}
+
+	/* Update the current status of LID */
+	report_lid_switch(BIT_LID_DETECT_ON);
+
+#ifdef CONFIG_LOONGSON_SUSPEND
+	/* Install the real yeeloong_report_lid_status for pm.c */
+	yeeloong_report_lid_status = report_lid_switch;
+#endif
+
+	return 0;
+}
+
+static void yeeloong_hotkey_exit(void)
+{
+	/* Free irq */
+	remove_irq(SCI_IRQ_NUM, &sci_irqaction);
+
+#ifdef CONFIG_LOONGSON_SUSPEND
+	/* Uninstall yeeloong_report_lid_status for pm.c */
+	if (yeeloong_report_lid_status == report_lid_switch)
+		yeeloong_report_lid_status = NULL;
+#endif
+
+	if (yeeloong_hotkey_dev) {
+		sparse_keymap_free(yeeloong_hotkey_dev);
+		input_unregister_device(yeeloong_hotkey_dev);
+		yeeloong_hotkey_dev = NULL;
+	}
+}
+
+#ifdef CONFIG_PM
+static void usb_ports_set(int status)
+{
+	status = !!status;
+
+	ec_write(REG_USB0_FLAG, status);
+	ec_write(REG_USB1_FLAG, status);
+	ec_write(REG_USB2_FLAG, status);
+}
+
+static int yeeloong_suspend(struct device *dev)
+
+{
+	if (ec_version_before("EC_VER=PQ1D27"))
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_OFF);
+	yeeloong_crt_vo_set(BIT_CRT_DETECT_UNPLUG);
+	usb_ports_set(BIT_USB_FLAG_OFF);
+
+	return 0;
+}
+
+static int yeeloong_resume(struct device *dev)
+{
+	if (ec_version_before("EC_VER=PQ1D27"))
+		yeeloong_lcd_vo_set(BIT_DISPLAY_LCD_ON);
+	yeeloong_crt_vo_set(BIT_CRT_DETECT_PLUG);
+	usb_ports_set(BIT_USB_FLAG_ON);
+
+	return 0;
+}
+
+static const SIMPLE_DEV_PM_OPS(yeeloong_pm_ops, yeeloong_suspend,
+	yeeloong_resume);
+#endif
+
+static struct platform_device_id platform_device_ids[] = {
+	{
+		.name = "yeeloong_laptop",
+	},
+	{}
+};
+
+MODULE_DEVICE_TABLE(platform, platform_device_ids);
+
+static struct platform_driver platform_driver = {
+	.driver = {
+		.name = "yeeloong_laptop",
+		.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+		.pm = &yeeloong_pm_ops,
+#endif
+	},
+	.id_table = platform_device_ids,
+};
+
+static int __init yeeloong_init(void)
+{
+	int ret;
+
+	pr_info("Load YeeLoong Laptop Platform Specific Driver.\n");
+
+	/* Register platform stuff */
+	ret = platform_driver_register(&platform_driver);
+	if (ret) {
+		pr_err("Fail to register yeeloong platform driver.\n");
+		return ret;
+	}
+
+	ret = yeeloong_backlight_init();
+	if (ret) {
+		pr_err("Fail to register yeeloong backlight driver.\n");
+		yeeloong_backlight_exit();
+		return ret;
+	}
+
+	ret = yeeloong_bat_init();
+	if (ret) {
+		pr_err("Fail to register yeeloong battery driver.\n");
+		yeeloong_bat_exit();
+		return ret;
+	}
+
+	ret = yeeloong_hwmon_init();
+	if (ret) {
+		pr_err("Fail to register yeeloong hwmon driver.\n");
+		yeeloong_hwmon_exit();
+		return ret;
+	}
+
+	ret = yeeloong_vo_init();
+	if (ret) {
+		pr_err("Fail to register yeeloong video output driver.\n");
+		yeeloong_vo_exit();
+		return ret;
+	}
+
+	ret = yeeloong_hotkey_init();
+	if (ret) {
+		pr_err("Fail to register yeeloong hotkey driver.\n");
+		yeeloong_hotkey_exit();
+		return ret;
+	}
+
+	return 0;
+}
+
+static void __exit yeeloong_exit(void)
+{
+	yeeloong_hotkey_exit();
+	yeeloong_vo_exit();
+	yeeloong_hwmon_exit();
+	yeeloong_bat_exit();
+	yeeloong_backlight_exit();
+	platform_driver_unregister(&platform_driver);
+
+	pr_info("Unload YeeLoong Platform Specific Driver.\n");
+}
+
+module_init(yeeloong_init);
+module_exit(yeeloong_exit);
+
+MODULE_AUTHOR("Wu Zhangjin <wuzhangjin@gmail.com>; Liu Junliang <liujl@lemote.com>");
+MODULE_DESCRIPTION("YeeLoong laptop driver");
+MODULE_LICENSE("GPL");
diff -Nur linux-2.6.36.orig/drivers/staging/sm7xx/smtcfb.c linux-2.6.36/drivers/staging/sm7xx/smtcfb.c
--- linux-2.6.36.orig/drivers/staging/sm7xx/smtcfb.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/drivers/staging/sm7xx/smtcfb.c	2010-11-18 11:47:59.000000000 +0100
@@ -12,6 +12,8 @@
  *  License. See the file COPYING in the main directory of this archive for
  *  more details.
  *
+ * - Remove the buggy 2D support for Lynx, 2010/01/06, Wu Zhangjin
+ *
  * Version 0.10.26192.21.01
  *	- Add PowerPC/Big endian support
  *	- Add 2D support for Lynx
@@ -107,6 +109,7 @@
 	{"0x307", 1280, 1024, 8},
 
 	{"0x311", 640,  480,  16},
+	{"0x313", 800,  480,  16},
 	{"0x314", 800,  600,  16},
 	{"0x317", 1024, 768,	16},
 	{"0x31A", 1280, 1024, 16},
diff -Nur linux-2.6.36.orig/drivers/usb/host/ohci-hcd.c linux-2.6.36/drivers/usb/host/ohci-hcd.c
--- linux-2.6.36.orig/drivers/usb/host/ohci-hcd.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/drivers/usb/host/ohci-hcd.c	2010-11-18 11:47:59.000000000 +0100
@@ -832,9 +832,13 @@
 	}
 
 	if (ints & OHCI_INTR_WDH) {
-		spin_lock (&ohci->lock);
-		dl_done_list (ohci);
-		spin_unlock (&ohci->lock);
+		if (ohci->hcca->done_head == 0) {
+			ints &= ~OHCI_INTR_WDH;
+		} else {
+			spin_lock (&ohci->lock);
+			dl_done_list (ohci);
+			spin_unlock (&ohci->lock);
+		}
 	}
 
 	if (quirk_zfmicro(ohci) && (ints & OHCI_INTR_SF)) {
diff -Nur linux-2.6.36.orig/net/rfkill/core.c linux-2.6.36/net/rfkill/core.c
--- linux-2.6.36.orig/net/rfkill/core.c	2010-10-20 22:30:22.000000000 +0200
+++ linux-2.6.36/net/rfkill/core.c	2010-11-18 11:48:02.000000000 +0100
@@ -112,7 +112,7 @@
 static DEFINE_MUTEX(rfkill_global_mutex);
 static LIST_HEAD(rfkill_fds);	/* list of open fds of /dev/rfkill */
 
-static unsigned int rfkill_default_state = 1;
+static unsigned int rfkill_default_state;	/* default: 0 = radio off */
 module_param_named(default_state, rfkill_default_state, uint, 0444);
 MODULE_PARM_DESC(default_state,
 		 "Default initial state for all radio types, 0 = radio off");